• Structural Engineering and Mechanics
• /
• v.46 no.2
• /
• pp.231-244
• /
• 2013

An efficient method is proposed here to identify multiple damage cases in structural systems using the concepts of flexibility matrix and strain energy of a structure. The flexibility matrix of the structure is accurately estimated from the first few mode shapes and natural frequencies. Then, the change of strain energy of a structural element, due to damage, evaluated by the columnar coefficients of the flexibility matrix is used to construct a damage indicator. This new indicator is named here as flexibility strain energy based index (FSEBI). In order to assess the performance of the proposed method for structural damage detection, two benchmark structures having a number of damage scenarios are considered. Numerical results demonstrate that the method can accurately locate the structural damage induced. It is also revealed that the magnitudes of the FSEBI depend on the damage severity.

• Journal of the Korean institute of surface engineering
• /
• v.49 no.5
• /
• pp.461-466
• /
• 2016

Nanocrystalline vanadium nitride (VN) coatings were deposited using asymmetric bipolar pulsed dc sputtering to further understand the influence of the pulsed plasmas on the crystal structure, microstructure and mechanical properties. Properties of VN coatings were investigated with FE-SEM, XRD and nanoindentation. The results show that, with the increasing pulse frequency and decreasing duty cycle, the coating morphology changed from a porous columnar to a dense structure, with finer grains. Asymmetric bipolar pulsed dc sputtered VN coatings showed higher hardness, elastic modulus and residual compressive stress than dc sputtered VN coatings. The results suggest that asymmetric bipolar pulsed dc sputtering technique is very beneficial for the reactive sputtering deposition of VN coatings.

• Journal of the Korean Vacuum Society
• /
• v.12 no.3
• /
• pp.174-181
• /
• 2003

Ta diffusion barriers have been deposited on Si (100) substrate by applying a negative substrate bias voltage. The effect of the substrate bias voltage on the properties of the Ta films was investigated. In the case of the Ta films deposited without the substrate bias voltage, a columnar structure and small grains were observed distinctly, and the electrical resistivity of the deposited Ta films was very high (250 $\mu\Omega$cm). By applying the substrate bias voltage, no clear columnar structure and grain boundary were observed. The resistivity of the Ta films decreased remarkably and at a bias voltage of -125 V, reaching a minimum value of 40 $\mu\Omega$cm, which is close to that of Ta bulk (13 $\mu\Omega$cm). The thermal stability of Cu(100 mm)/Ta(50 mm)/Si structures was evaluated after annealing in H2 atmosphere for 60 min at various temperatures. The Ta films deposited by applying the substrate bias voltage were found to be stable up to $600^{\circ}C$, while the Ta films deposited without the substrate bias voltage degraded at $400^{\circ}C$.

• Journal of Adhesion and Interface
• /
• v.15 no.4
• /
• pp.161-168
• /
• 2014

New self-assembled discotic liquid crystals have been prepared through single hydrogen bonding between phenol and pyridine moieties, and their liquid crystalline properties were investigated. For the construction of discotic structure, we used phloroglucinol as a core molecule and trans-4-alkoxy-4'-stilbazoles with systematically varied alkyl chain lengths as peripheral units. FTIR results showed that the intermolecular hydrogen bonds between core and peripheral molecules are successfully formed, and the stability of the hydrogen bond is strongly influenced by molecular ordering. Discotic complexes exhibited different liquid crystalline phases depending on the length of alkyl chains around the discotic mesogen. The discotic complexes with longer alkyl chains showed hexagonal columnar mesophases, while the other complexes formed nematic columnar mesophases. These results indicated that the type of mesophase structure was strongly dependent on the alkyl chain length around the aromatic core.

• Journal of the Korean Magnetics Society
• /
• v.21 no.5
• /
• pp.185-192
• /
• 2011

The technique of producing thin film plays a crucial role in modern science and technology as well as in industrial purposes. Numerous efforts have been made to get high quality thin film through surface treatment of materials. PVD (Physical Vapor Deposition) and CVD (Chemical Vapor Deposition) are two of the most popular deposition techniques used in both scientific study and industrial use. It is well known that the film deposited by PVD and CVD commonly possesses a columnar microstructure which affects many film properties. In recent years, various types of deposition sources which feature high material uses and excellent film properties have been developed. Electromagnetic levitation source appeared as an alternative deposition source to realize high deposition rate for industrial use. Complex film structures such as nano multilayer and multi-components have been prepared to achieve better film properties. Glancing angle deposition (GLAD) has also been developed as a technique to engineer the columnar structure of thin films on the micro- and nanoscale. In this paper, the trends and major issues of thin film technology based on PVD and CVD have been discussed together with the prospect of thin film technology.

• Nano
• /
• v.13 no.10
• /
• pp.1850124.1-1850124.12
• /
• 2018

$TiO_2$ films were deposited from oxygen/titanium tetraisopropoxide (TTIP) plasmas at low temperature by Helicon-PECVD at floating potential ($V_f$) or substrate self-bias of -50 V. The influence of titanium precursor partial pressure on the morphology, nanostructure and optical properties was investigated. Low titanium partial pressure ([TTIP] < 0.013 Pa) was applied by controlling the TTIP flow rate which is introduced by its own vapor pressure, whereas higher titanium partial pressure was formed through increasing the flow rate by using a carrier gas (CG). Then the precursor partial pressures [TTIP+CG] = 0:027 Pa and 0.093 Pa were obtained. At $V_f$, all the films exhibit a columnar structure, but the degree of inhomogeneity is decreased with the precursor partial pressure. Phase transformation from anatase ([TTIP] < 0.013 Pa) to amorphous ([TTIP+CG] = 0:093 Pa) has been evidenced since the $O^+_2$ ion to neutral flux ratio in the plasma was decreased and more carbon contained in the film. However, in the case of -50 V, the related growth rate for different precursor partial pressures is slightly (~15%) decreased. The columnar morphology at [TTIP] < 0.013 Pa has been changed into a granular structure, but still homogeneous columns are observed for [TTIP+CG] = 0:027 Pa and 0.093 Pa. Rutile phase has been generated at [TTIP] < 0:013 Pa. Ellipsometry measurements were performed on the films deposited at -50 V; results show that the precursor addition from low to high levels leads to a decrease in refractive index.

• Korean Journal of Ichthyology
• /
• v.19 no.1
• /
• pp.16-23
• /
• 2007

Oocyte surface in two Korean minnows, Rhynchocypris oxycephalus and R. kumgangensis was examined by light and electron microscope. In two species, the development of the oocyte was similar, but the follicular layer surrounding full-grown oocyte showed an evident difference. In R. oxycephalus, the follicular layer at the yolk vesicle stage became bilaminar with the retention of its outer squamous cell layer and the acquisition of an inner cuboidal or round cell layer just over the zona radiata. As the oocyte grows, the cuboidal cells of the inner follicular layer began to be replaced by columnar cells. At the yolk granule stage, the columnar cells secreted mucin to their cytoplasm (adhesive materials) and then surround the entire oocyte, as bundles of fence-shaped structures. Whereas, although the follicular layer of R. kumgangensis had an outer squamous layer and an inner cuboidal or round cell layer at the yolk vesicles as in R. oxycephalus, no inner cells were more changed with the retention of its cuboidal or round cells. Finally, in R. kumgangensis, the adhesive materials did not occur. In Korean two minnows, the structural difference in the oocyte surface seems to be related to their habitats and spawning characteristics as well as taxonomic characters.

• Korean Journal of Ichthyology
• /
• v.28 no.1
• /
• pp.19-27
• /
• 2016

The RLG (relative length of gut) is 1.52 (n=12) in the sablefish, Anoplopoma fimbria. The digestive tract has five or six pyloric caeca in the posterior region of stomach. Morphology of mucosal fold is unbranched type in the esophagus and stomach, but branched type in the intestine. The histological structure of digestive tract can be divided into mucosal layer, submucosal layer, muscular layer and serous membrane in the cross section. In the esophagus, mucosal epithelial layer is a simple, and consists of ciliated columnar epithelia and mucous cells. In the stomach, gastric gland of mucosal epithelial layer is a tubular, and is composed of chief cell, parietal cell and mucin secreting cell, which is columnar and contained secretory granules of red and blue colors in the AB-PAS (pH 2.5) reaction. In the intestine, mucosal epithelial layer is a simple, and consists of ciliated columnar epithelia and goblet cells. The submucosal layer is composed mainly of collagen fibers, and well developed in the esophagus. And the muscular layer of digestive tract is divided into longitudinal and circular muscle layer, and well developed in the stomach. The liver is composed of numerous lobular structure and bile canaliculi. Stainability of hepatocyte cytoplasm was eosinophilic, and nucleus and nucleolus showed basophilic in the H-E stain. The pancreatic tissue was scattered in the fatty tissue near the digestive tract, and acinar gland consisting of numerous exocrine cells. And cytoplasmic stainability of exocrine cell was basophilic, and contained numerous zymogen granules of eosinophilic in the H-E stain.

• Journal of the Korean institute of surface engineering
• /
• v.17 no.4
• /
• pp.106-119
• /
• 1984

Brass was electrodeposited over the range of the current densities from 2 to 8 A/$dm^2$ in cyanide bath at 20 and 40$^{\circ}C$. The cathode overpotential increased and the cathode efficiency was decreased respectively with decreasing temperature, increasing current density and addition of organic substance. The perferred orientation of the deposits were associated with the cathode overpotential and the nucleation energy of lattice planes. The (111) preferred orientation developed at the low current density and low cathode overpotential (440-520mV). On the other hand, the (111)+(100) preferred orientation developed at higher cathode overpotential (528-680mV). The (111)+(100) preferred orientation developed over the whole range of overpotential in the cyanide solution with organic additive. The copper content of deposit decreased with increasing current density and decreasing temperature. The morphology of the deposits with no additive was the polygonal body type of structure and the structure of the cross section was columnar structure. The morphology of the deposits with additive, on the other hand, was fine crystallite type of structure. And the structure of the cross section of them was the finer granular structure.

• Journal of the Korean institute of surface engineering
• /
• v.48 no.5
• /
• pp.205-210
• /
• 2015

NbN coatings were prepared by ICP (inductively coupled plasma) assisted magnetron sputtering from a Nb metal target in $Ar+N_2$ atmosphere at various ICP powers. Effect of ICP on the microstructure, crystalline structure and mechanical properties of NbN coatings was investigated by field emission electron microscopy, X-ray diffraction, atomic force microscopy and nanoindentation measurements. The results show that ICP power has a significant influence on coating microstructure, structure and mechanical properties of NbN coatings. With the increasing of ICP power, coating microstructure evolves from the columnar structure of DC process to a highly dense one. Crystalline structure of NbN coatings were changed from cubic ${\delta}$-NbN to hexagonal ${\beta}-Nb_2N$ with increase of ICP power. The maximum nano hardness of 25.4 GPa with Ra roughness of 0.5 nm was obtained from the NbN coating sputtered at ICP power of 200 W.