• Resources Recycling
• /
• v.23 no.2
• /
• pp.61-70
• /
• 2014

LCD televisions and monitors use cold cathode fluorescence lamps (CCFLs) to illuminate the screen. Most CCFLs contain mercury and they have to be carefully handled at the end of their lives as per minimum treatment standards under the Waste Electrical and Electronic Equipment (WEEE) and Restriction of Hazardous Substances (RoHS) directives. CCFLs were carefully separated from mold frames of waste LCD units for primary decontamination of mercury/fluorescent compound mixture using CCFL decontamination system designed and fabricated in the present research. Residual mercury was further removed by employing a pyro-process, where crushed CCFL tubes transferred from primary decontamination process were subject to heat treatment at $550^{\circ}C$ in a box furnace: more than 99% of mercury was removable from waste CCFLs.

• International Journal of Highway Engineering
• /
• v.11 no.1
• /
• pp.1-12
• /
• 2009

A new mix design procedure for cold in-place recycling using foamed asphalt (CIR-foam) has been developed for Iowa Department of Transportation. Some strengths and weaknesses of the new mix design parameters were considered and modified to improve the laboratory test procedure. Based on the critical mixture parameters identified, a new mix design procedure was developed and validated to establish the properties of the CIR-foam mixtures. As part of the validation effort to evaluate a new CIR-foam mix design procedure, dynamic moduli of CIR-foam mixtures made of seven different reclaimed asphalt pavement (RAP) materials collected throughout the state of Iowa were measured and their master curves were constructed. The main objectives of this study are to provide: 1) standardized testing procedure for measuring the dynamic modulus of CIR-foam mixtures using new simple performance testing (SPT) equipment; 2) analysis procedure for constructing the master curves for a wide range of RAP materials; and 3) impacts of RAP material characteristics on the dynamic modulus. Dynamic moduli were measured at three different temperatures and six different loading frequencies and they were consistent among different RAP sources. Master curves were then constructed for the CIR-foam mixtures using seven different RAP materials. Based upon the observation of the constructed master curves, dynamic moduli of CIR-foam mixtures were less sensitive to the loading frequencies than HMA mixtures. It can be concluded that at the low temperature, the dynamic modulus is affected by the amount of fines in the RAP materials whereas, at the high temperature, the dynamic modulus is influenced by the residual binder characteristics.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2003.12a
• /
• pp.174-174
• /
• 2003

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2005.06a
• /
• pp.110-120
• /
• 2005

For utilizing vitrification to treat low and intermediate level waste, industrial pilot plant was designed and constructed in October 1999 at Daejon, Korea through the joint research program among NETEC, MOBIS and SGN. More than 70 tests were performed on simulated IER, DAW etc. including key nuclide surrogate(Cs, Co); this plant has been shown to vitrify the target waste effectively and safely, however, some dust are generated from the HTF(High Temperature Filter) as a secondary waste. In case of long term operation, it is also concerned that pipe plugging can be occurred due to deposited dust in cooling pipe namely, connecting pipe between CCM(Cold Crucible Melter) and HTF. In this regard, we have developed the special complementary system of the off-gas treatment system to recycle the dust from HTF to CCM and to remove the interior dust of cooling pipe. Main concept of the dust recycling is to feed the dust to the CCM as a slurry state; this system is regarded as of an important position in the viewpoint of volume reduction, waste disposal cost and glass melt control in CCM. The role of DRS(Dust Recycling System) is to recycle the major glass components and key nuclides; this system is served to lower glass viscosity and increase waste solubility by recycling B, Na, Li components into glass melt and also to re-entrain and incorporate into glass melt like Cs, Co. Therefore dust recycling is helpful to control the molten glass; it is unnecessary to consider a separate dust treatment system like a cementation equipment. The effects of Dust Cleaner are to prevent the pipe plugging due to dust and to treat the deposited dust by raking the dust into CCM. During the pilot vitrification test, overall performance assessment was successfully performed; DRS and Dust Cleaner are found to be useful and effective for recycling the dust from HTF and also removing the dust in cooling pipe. The obtained operational data and operational experiences will be used as a basis of the commercial facility.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2006.05a
• /
• pp.56-60
• /
• 2006

In 2005, the imports of titanium metals was about 22.8 million US$(7,700 tons) in Korea. New scrap produced was estimated to be 359 tons and the exports were about 352 tons. Generally scrap is recylced into titanium ingot either with or without virgin metal using traditional vacuum-arc-melting and cold hearth melting. In Korea, there is no titanium ingot producers(recyclers). In this paper, the brief summary of major titanium melting technology, such as vacuum arc remelting(VAR), electron beam melting(EBM), plasma arc melting(PAM) is given and discussed. In view of titanium market situation of Korea, the technological development of ingot production from scrap is big problem to be solved in order to realize extensive cost reduction for titanium products.

• Resources Recycling
• /
• v.3 no.1
• /
• pp.25-31
• /
• 1994

This paper was focused to optimize hot extrusion condition of Mg machined chips and scraps as fundamental basic research for the recycle of Mg alloy. We have been performed to extrude at $300~380^{\circ}C$ temperature range under the extrusion ratio of 25:1 after cold-pressing AZ91 Mg machined chips and scraps. AZ91 Mg ingots was used as reference materials. Microstructure observation showed that the extruded machined chips were perfectly bonded and extruded materials became fine grain size($20\mu\textrm{m}$) by recrystallization during hot extrusion. The specimens extruded from the machined chips, scraps and Mg ingot indicated tensile strength of 330MPa and the elongation of 10% at room temperature.

• International Journal of Highway Engineering
• /
• v.17 no.2
• /
• pp.21-30
• /
• 2015

PURPOSES : The purpose of this study was to evaluate the performance of rapid-setting polymer-modified asphalt mixtures with a high reclaimed asphalt pavement (RAP) content. METHODS: A literature review revealed that emulsified asphalt is actively used for cold-recycled pavement. First, two types of rapid-setting polymer-modified asphalt emulsion were prepared for application to high-RAP material with no virgin material content. The quick-setting polymer-modified asphalt mixtures using two types of rapid-setting polymer-modified asphalt emulsion were subjected to the following tests: 1) Marshall stability test, 2) water immersion stability test and 3) indirect tensile strength ratio test. RESULTS AND CONCLUSIONS : Additional re-calibration of the RAP was needed for laboratory verification because the results of analyzing RAP aggregates, which were collected from different job sites, did not deviate from the normal range. The Marshall stability of each type of binder under dry conditions was good. However, the Type B mixtures with bio-additives performed better in the water immersion stability test. Moreover, the overall results of the indirect tensile strength test of RAP mixtures with Type B emulsions exceeded 0.7. Further research, consisting of lab testing and on-site application, will be performed to verify the possibility of using RAP for minimizing the closing of roadways.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.16 no.4
• /
• pp.141-148
• /
• 2006

Skull melting method can be a good candidate for growing oxide single crystals with high quality and for mass production because of its low production costs and high yield through recycling of crust. In this study, rutile single crystals were frown by the skull melting method and ingot characteristics with the variation of different growth conditions has been investigated. Conditions for high quality rutile ingot growth were used for producing cold-crucible size of ${\Phi}12cm{\times}H14cm$, capacity of 3000 pF tank condenser, work frequency of 2.84 MHz, melt-dwelling time of 9hrs and growing speed of 2 mm/h.

• Progress in Superconductivity and Cryogenics
• /
• v.23 no.3
• /
• pp.55-59
• /
• 2021

A thermoelectric cooler (TEC) is promising as an alternative refrigeration technology for the sake of its inherent advantages; no-moving parts and refrigerant-free in its operation. Due to the compactness, reliability and excellence in temperature stability, TECs have been widely used for small cooling devices. In recent years, thermoelectric devices have been attractive technologies that not only serve the needs of cooling and heating applications but also meet the demand for energy by recycling waste heat. In this research paper, multistage TEC is proposed as a concept of demonstrating the idea of transient cooling technology. The key idea of transient cooling is to harnesses the thermal mass installed at the interfacial level of the stages. By storing heat temporally at the thermal mass, the multistage TEC can readily reach lower temperatures than that by a steady-state operation. The multistage TEC consists of four different sizes of thermoelectric modules and they are operated with an optimized current. Once the cold-part of the uppermost stage is reached at the no-load temperature, the current is successively supplied to the lower stages with a certain time interval; 25, 50 and 75 seconds. The results show the temperatures that can be ultimately reached at the cold-side of the lowermost stage are 197, 182 and 237 K, respectively. It can be concluded that the timing or total amount of the current fed to each thermoelectric module is the key parameter to determine the no-load temperature.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.2
• /
• pp.55-63
• /
• 2009

This study was performed to evaluate the heavy metal contents in various packaging board. Domestic and foreign OCC (old corrugated containers) and old duplex boards were used as raw materials. Tests were made for the printed and unprinted parts of the sample. Heavy metal contents of old food packaging boards made from virgin pulp fibers were also evaluated. The contents of heavy metals including lead (Pb), cadmium (Cd), barium (Ba), arsenic (As), antimony (Sb), selenium (Se), and mercury (Hg) were determined using ICP-AES (Inductively Coupled Plasma - Atomic Emission Spectrometer), and CV-AAS (Cold vapor-atomic absorption spectrometer) after digesting the samples in a microwave oven. The contents of heavy metals contained in domestic packaging board were higher than those in overseas samples, and OCC showed higher contents of heavy metals than old duplex boards. Printed parts gave greater heavy metal contents than unprinted parts. Results indicate that recycling of paper and paperboard products increases the heavy metal contamination of the paper packaging products and this derives mostly from the heavy metals contained in printing inks. Recycling processes that decrease heavy metals in recycled fibers and new printing inks that contains less heavy metals should be developed to solve the problem associated with the heavy metals in packaging paper products.