• 한국세라믹학회지
• /
• 제50권2호
• /
• pp.142-148
• /
• 2013

Conventional cold isostatic pressing, slip casting, and filter pressing are not completely suitable for fabricating large plates because of disadvantages such as the high cost of equipment and formation of density gradient. These problems could be avoided by employing pressure-vacuum hybrid slip casting (PVHSC). In the PVHSC, the consolidation occurs not only by the compression of the slip in casting room, but also by vacuum sucking of the dispersion medium around the mold. We prepared the alumina bodies by the PVHSC in a static- or stepwise-pressure manner for loading up to 0.5 MPa using an aqueous slip. The green bodies were dried at $30^{\circ}C$ with 40 ~ 80% relative humidity. Under static pressure, casting induced a density gradient in the formed body, resulting in cracking and distortion after the firing. However, the stepwise pressure loading resulted in green bodies with homogeneous density, and the minimization of the appearance of those defects in final products. Desirable drying results were obtained from the cast bodies dried with 80% RH environment humidity. When sintered at $1650^{\circ}C$ for 4 h, the alumina plate made by stepwise-pressure casting reached full density (> 99.7% relative density).

• 한국세라믹학회지
• /
• 제49권6호
• /
• pp.592-600
• /
• 2012

Conventional methods for preparing ceramic bodies, such as cold isostatic pressing, gypsum-mold slip casting, and filter pressing are not completely suitable for fabricating large and thick ceramic plates owing to disadvantages of these processes, such as the high cost of the equipment, the formation of density gradients, and differential shrinkage during drying. These problems can be avoided by employing a pressure-vacuum hybrid slip casting approach that considers not only by the compression of the aqueous slip in the casting room (pressure slip casting) but also the vacuum sucking of the dispersion medium (water) around the mold (vacuum slip casting). We prepared the alumina formed bodies by means of pressure-vacuum hybrid slip casting with stepwise pressure loading up to 0.5 MPa using a slip consisting of 40 vol% solid, 0.6 wt% APC, 1 wt% PEG, and 1 wt% PVA. After drying the green body at $30^{\circ}C$ and 80% RH, the green density of the alumina bodies was about 56% RD. The sintered density of an alumina plate created by means of sintering at $1650^{\circ}C$ for 4 h exceeded 99.8%.This method enabled us to fabricate a $110{\times}110{\times}20$ mm alumina plate without cracks and with a homogeneous density, thus demonstrating the possibility of extending the method to the fabrication of other ceramic products.

• 한국수소및신에너지학회논문집
• /
• 제9권4호
• /
• pp.161-167
• /
• 1998

Ni/MH 2차전지의 음극용 금속간화합물전극의 부식특성에 미치는 합금원소와 결합제의 영향을 조사하였다. 전극의 재료는 $(LM)Ni_{4.49}Co_{0.1}Mn_{0.205}Al_{0.205}$와 $(LM)Ni_{3.6}Co_{0.7}Mn_{0.3}Al_{0.4}$의 $AB_5$ type합금을 모재로 하였다. 여기에 Si sealant 또는 PTFE를 결합제로 첨가한 것과 원재료 분말에 구리를 20% 무전해도금한 것을 냉간 압착하여 전극을 제조하였다. 부식특성을 조사하기위해 탈공기된 6M의 KOH 용액에서 동전위법과 순환전위법을 이용하여 부식전류와 전류밀도를 측정하였다. 모재에 Co가 많이 함유되면 전극의 내식성을 향상시키고 Ni이 많이 함유되면 충전과 방전을 반복하는 동안에 전극의 안정성을 저하시켰다. 부식전류밀도는 Si sealant를 결합제로 사용한 전극의 경우가 PTFE를 사용한 전극의 경우보다 낮았고 Cu가 도금된 전극은 내식성에서 가장 우수하게 나타났다.

• 한국응용과학기술학회지
• /
• 제33권3호
• /
• pp.560-567
• /
• 2016

최근 건강기능성 식용유에 대한 선호도가 높아지면서 저온압착(cold-pressing) 유채유에 대한 관심이 증대되고 있다. 저온압착 유채유는 정제유에 비해 기름 고유의 맛과 향을 느낄 수 있는 장점이 있다. 본 연구에서는 산성백토를 이용한 저온압착 유채유의 탈색과정에서 산성백토의 첨가량, 처리시간 및 반응온도에 따른 탈색 후 이화학적 특성과 품질특성을 분석하고자 하였다. 이화학적 특성으로 색차(명도, 적색도, 황색도)를 조사하였고, 품질특성은 chlorophyll-A 와 carotenoid 함량, 지방산 조성, 토코페롤(${\alpha}$, ${\beta}$, ${\gamma}$, ${\delta}$), 및 식물성 스테롤(${\beta}$-sitosterol, campesterol, stigmasterol)을 분석하였다. 먼저 산성백토(DC-SUPER)의 첨가량(1, 2, 3%)에 따른 저온압착 유채유의 색도변화를 관찰한 결과, DC-SUPER 첨가량 2%에서 탈색 1시간 후 유채유의 색도가 갈색에서 연노랑으로 옅어졌다. 본 결과를 바탕으로 총 3종의 산성백토(DC-SUPER, DC-A3, 및 P1)에 대해 첨가량 2%를 기준으로 처리시간(20, 40, 60, 80분) 증가에 따른 색차를 조사한 결과, 처리시간 20분 경과 후부터 대조구 대비 명도(L)는 증가하였고, 적색도(a)와 황색도(b)는 감소하는 경향을 보였다. 또한 산성백토 DC-SUPER 2% 첨가 후, 반응온도(40, 80, $120^{\circ}C$) 증가에 따른 색차를 조사한 결과, L값과 a값은 큰 변화를 보이지 않았으나, b값은 급격히 감소하는 경향을 보였다. 특히, 반응온도 $40^{\circ}C$에서 처리시간 20분 이내에 클로로필 A와 카로티노이드는 대부분 제거되었고, 토코페롤 함량도 현저히 감소하였다. 탈색 전 저온압착 유채유의 총 토코페롤 함량은 46.62mg/100g이나, 탈색 후 총 토코페놀은 12.67mg/100g(20분 탈색), 15.31mg/100g(40분 탈색), 13.56mg/100g(60분 탈색)로 나타나, 약 50% 이상 감소하였다. 탈색 후 ${\alpha}$-토코페롤과 ${\delta}$-토코페롤의 함량 감소가 매우 컸고, ${\gamma}$>${\beta}$>${\alpha}$>${\delta}$-토코페롤의 순으로 포함되어 있었다. 하지만 탈색 전 후에 저온압착 유채유의 식물성 스테롤 함량은 큰 변화가 없었다. 따라서 본 연구에서는 산성백토 이용 저온압착 유채유 탈색시 색도를 향상시킴을 확인하였으며, 영양학적으로 우수한 총 토코페롤 등이 감소한 바 향후 이를 보완 할 수 있는 연구가 필요하다.

• 한국강구조학회 논문집
• /
• 제21권5호
• /
• pp.515-526
• /
• 2009

콘크리트 충전강관에 사용되는 강관의 제작법은 재단된 4장의 플레이트를 모서리에서 용접하는 일반강관 제작법과, ㄷ형으로 절곡성형과정을 거쳐 2-Seam으로 용접하는 제작방법, 그리고 원형강관을 압축하여 4각형태로 만드는 방법등이 일반적으로 사용되며, 강관제작에 사용되는 용접방법과 용접량의 선택은 강관 제작비용에 큰 부분을 차지하고 있다. 새로운 제작형식으로 개발된 각형강관은 4장의 플레이트를 ㄱ형으로 절곡성형한 후 강관 폭의 중앙에서 4-Seam Flare 용접하는 방식이다. 본 연구에서는 새로운 제작형식의 CFT 각형 기둥에 대하여 용접량 평가를 위한 실험방법을 제시하고, 강관 제작법, 강관두께 및 용접량을 변수로 총 6개의 실험체를 제작하여 구조실험 및 해석을 수행하여 강관내부의 수압에 따른 강관의 거동을 평가하였다.

• 한국전기전자재료학회논문지
• /
• 제32권4호
• /
• pp.333-340
• /
• 2019

The effects of compaction methods on the sintering density, microstructures, and mechanical properties were investigated in ${\alpha}-alumina$ ceramics. ${\alpha}-Alumina$ powders were granulated with a 10% aqueous solution of polyvinyl alcohol (PVA). Uniaxially pressed (UAP) and cold isostatic-pressed (CIP) samples were prepared by pressing uniaxially at a pressure of 1 ton for 1 min, and isostatically at 200 MPa for 15 min, respectively. Subsequently, both types of samples were sintered at $1,200^{\circ}C$, $1,300^{\circ}C$, $1,400^{\circ}C$, $1,450^{\circ}C$, $1,500^{\circ}C$, $1,550^{\circ}C$, and $1,600^{\circ}C$ at a rate of $5^{\circ}C/min$ for 2 h. The CIP samples were better than the UAP samples for all properties measured, such as the sintering density, Vicker's hardness, and toughness. The CIP sample sintered at $1,400^{\circ}C$ showed the maximum Vicker's hardness and toughness; this may be attributed to the competing effects of a decrease in porosity and the growth of grains with increasing sintering temperature.

• 대한한방내과학회지
• /
• 제21권1호
• /
• pp.169-180
• /
• 2000

Objectives : To satisfy the demand of good treatment of constipation Methods : we investigated the literatures of Oriental Medicine about Constipation. Results: 1. There are three categories of etimological factors of constipation, that is, endogenous, exogenous and non-exo-endogenous factor. The endogenous factor is caused by seven emotions, called depression of Ki and stagnation of Ki. The exogenous factor is six excessive atmospheric influences, for example, wind, cold, dampness, heat and dryness. And the non-exo-endogenous factors are overfatigue, improper diet, stagnated blood and deficiency of Ki and blood that comes from old age, long disease and after delivery. 2. Classification: According to cause of disease it is classified by constipation due to cold, heat, wind, dryness, retention of undigested and phlegm. According to Internal Organs there are constipation due to deficiency syndrome of the stomach, excess syndrome of the stomach, deficiency syndrome of kidney and splenic constipation. And Differentiation of syndromes according to Ki and blood, there are constipation of deficiency type and excess type. There are constipation due to stagnation and deficiency of Ki, deficiency of blood and stagnated blood. 3. Principles and Methods of treatment 1) Herbal Medicine (1) Excess type [1] Constipation due to heat : Seunggitang(承氣湯) and Majainwhan(麻子仁丸) [2] Constipation due to stagnation of Ki : Samatang(四磨湯) and Yukmatang(六磨湯) (2) Deficiency type [1] Constipation due to deficiency of Ki : Whanggitang(黃?湯) [2] Constipation due to deficiency of blood: Yunjangwhan(潤腸丸) [3] Constipation due to cold : Jechunjun(濟川煎) and Banyuwhan(半硫丸) 2) Enema therapy: It is a method to induce defecation by honey or pig's bile juice for weak people. 3) Acupuncture and Moxibustion: Acupoints used to treat constipation are BL25, ST25 and TE6. Moxibustion at CV8, CV6 is good for constipation due to cold. (4) Diet therapy: It is very important that we eat meals regularly and defecate on the same time even if you don't. And we have to eat food like fruits, vegetables and beans. (5) finger pressure: Finger pressing around these points like ST25, SP25, BL25, BL31, BL32, BL33 and BL34 is good for it. (6) Kigong therapy: Abdominal breathing (7) Old man' s constipation: Hip bath or diet therapy is commended. Laxation with lubricant like Supungyunjangwhan(搜風潤腸丸) is used. (8) Women' s constipation: After delivery, we have to administer tonifying prescription Sipjundaebotang(十全大補湯) and enema can be used. Conclusion : We have to examine the cause of disease and bowl movement carefully. After comprehensive analysis of the data gained by the four methods of diagnosis, we diagnose and treat patients on the base of overall of symptoms and signs.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 C
• /
• pp.1051-1053
• /
• 1995

Nowadays perovskite $La_{1-x}Sr_xMnO_3$ is preferred cathode material in Solid Oxide Fuel cell(SOFC). The $La_{1-x}Sr_xMnO_3$ with Sr contents ranging $x=0{\sim}1.0$ were prepared by a citrate method. These powders were characterized by usual means like TG/DTA, X-ray diffraction analysis. The samples used for measuring thermal expansion were prepared as pellets by cold pressing and subsequent sintering in air at $1200^{\circ}C$ for 5 hours. To measure the by-product of $La_{1-x}Sr_xMnO_3$ reacted with 8mol% YSZ, that samples were sintered at $1200^{\circ}C$ for 5 hours.

• 한국응용과학기술학회지
• /
• 제30권3호
• /
• pp.551-559
• /
• 2013

To investigate the adhesion effect of sodium bisulfite content in making blocked isocyanate, wood adhesive PB-1, PB-2, PB-3 and PB-4 containing sodium bisulfite content of 15%, 22.5%, 30% and 37.5% were synthesized respectively. As a result, when the amount of sodium bisulfite increased in adhesives, the tensile strength was found to be proportionally increased. The final adhesive mixtures were manufactured using a two-components system which are prepared by mixing two separate protein and BI solutions due to the precipitate in the adhesives. As PVA was added to adhesives to increase tenacity, the plywood dehiscence phenomenon after cold pressing process was declined. By addition of PVA, the tensile strength was improved up to $6.5{\sim}7kgf/cm^2$ with BI/protein ratio from 1:6 up to 1:8. Phase separation between milk fat and aqueous layer was disappeared after addition of emulsifier, Tween 20. Additon of Tween 20 showed tensile strength up to $5{\sim}6.5 kgf/cm^2$ at NCO/protein ratio of 1:12 ~ 1:14 without phase separation.

• 한국전기전자재료학회논문지
• /
• 제15권3호
• /
• pp.269-274
• /
• 2002

(Sm/Y)-Ba-Cu-O system high Tc composite superconductors with/without $CeO_2$ additive were directionally grown by zone-melting process, haying large temperature gradient, In air atmosphere. Cylindrical green rods of $({Sm/y})_{1.8}Ba_{2.4}Cu_{3.4}O_x$ [(Sm/Y)1.8] composite oxides by cold isostatic pressing(CIP) method using rubber mold were fabricated. The microstructure and superconducting properties were investigated by XRD, SEM, TEM and SQUID magnetometer. The size of nonsuperconducting $({Sm/y})_2BaCuO_5$ inclusions of the melt-textured (Sm/Y)1.8 sample with CeO$_2$ additive were remarkably reduced and uniformly distributed within the superconducting (Sm/Y)1.8 matrix. Both samples, with/without $CeO_2$ additive, showed an onset Tc $\geq$ 90 K and sharp superconducting transition. The critical current density Jc value of the $CeO_2$ addictive were $1{\times}10^5A/\textrm{cm}^2$ in 77 K, 0 Tesla.