• Journal of the Korean Ceramic Society
• /
• v.50 no.2
• /
• pp.142-148
• /
• 2013

Conventional cold isostatic pressing, slip casting, and filter pressing are not completely suitable for fabricating large plates because of disadvantages such as the high cost of equipment and formation of density gradient. These problems could be avoided by employing pressure-vacuum hybrid slip casting (PVHSC). In the PVHSC, the consolidation occurs not only by the compression of the slip in casting room, but also by vacuum sucking of the dispersion medium around the mold. We prepared the alumina bodies by the PVHSC in a static- or stepwise-pressure manner for loading up to 0.5 MPa using an aqueous slip. The green bodies were dried at $30^{\circ}C$ with 40 ~ 80% relative humidity. Under static pressure, casting induced a density gradient in the formed body, resulting in cracking and distortion after the firing. However, the stepwise pressure loading resulted in green bodies with homogeneous density, and the minimization of the appearance of those defects in final products. Desirable drying results were obtained from the cast bodies dried with 80% RH environment humidity. When sintered at $1650^{\circ}C$ for 4 h, the alumina plate made by stepwise-pressure casting reached full density (> 99.7% relative density).

• Journal of the Korean Ceramic Society
• /
• v.49 no.6
• /
• pp.592-600
• /
• 2012

Conventional methods for preparing ceramic bodies, such as cold isostatic pressing, gypsum-mold slip casting, and filter pressing are not completely suitable for fabricating large and thick ceramic plates owing to disadvantages of these processes, such as the high cost of the equipment, the formation of density gradients, and differential shrinkage during drying. These problems can be avoided by employing a pressure-vacuum hybrid slip casting approach that considers not only by the compression of the aqueous slip in the casting room (pressure slip casting) but also the vacuum sucking of the dispersion medium (water) around the mold (vacuum slip casting). We prepared the alumina formed bodies by means of pressure-vacuum hybrid slip casting with stepwise pressure loading up to 0.5 MPa using a slip consisting of 40 vol% solid, 0.6 wt% APC, 1 wt% PEG, and 1 wt% PVA. After drying the green body at $30^{\circ}C$ and 80% RH, the green density of the alumina bodies was about 56% RD. The sintered density of an alumina plate created by means of sintering at $1650^{\circ}C$ for 4 h exceeded 99.8%.This method enabled us to fabricate a $110{\times}110{\times}20$ mm alumina plate without cracks and with a homogeneous density, thus demonstrating the possibility of extending the method to the fabrication of other ceramic products.

• Transactions of the Korean hydrogen and new energy society
• /
• v.9 no.4
• /
• pp.161-167
• /
• 1998

It has been investigated the effects of alloying elements and binders on the corrosion behavior of metal hydride electrodes for anode of Ni/MH secondary battery. The $AB_5$-type alloys, $(LM)Ni_{4.49}Co_{0.1}Mn_{0.205}Al_{0.205}$ and $(LM)Ni_{3.6}Co_{0.7}Mn_{0.3}Al_{0.4}$, were used for the experiments. The electrodes were prepared by mixing and cold-pressing of alloy powders with Si sealent or PTFE powders, or cold-pressing the electroless copper coated alloy powders. The amount of copper coating was 20wt%. In order to examine corrosion behavior of the electrodes, the corrosion current and the current density, in 6M KOH aqueous solution after removal of oxygen in the solution, were measured by potentiodynamic and cyclic voltamo methods. The results showed that Co in the alloy increased corrosion resistance of the electrode whereas Ni decreased the stability of the electrode during the charge-discharge cycles. The electrode used Si sealant as a binder showed a lower corrosion current density than the electrode used PTFE and the electrode used Cu-coated alloy powders showed the best corrosion resistance.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.3
• /
• pp.560-567
• /
• 2016

Acid-activated clays (SUPER-DC, DC-A3, and P1) are used for the bleaching of cold-pressed rapeseed oil. In this study we tested the bleaching performance of cold-pressed rapeseed oil according to the different reaction time (20, 40, 60, 80 min) and temperature (40, 80, $120^{\circ}C$). Oil color (lightness, redness, yellowness), pigments (chlorophyll A and carotenoid content) and quality properties (fatty acid composition, tocopherols (${\alpha}$, ${\beta}$, ${\gamma}$, ${\delta}$), and plant sterols (${\beta}$-sitosterol, campesterol, stigmasterol) content) were analyzed. The results showed that bleaching of cold-pressed rapeseed oil with 2% acid-activated clays at $40^{\circ}C$ for 20 min, brightness (L) increased, but redness (a) and yellowness (b) decreased. Bleaching of cold-pressed rapeseed oil with 2% DC-SUPER at $40^{\circ}C$ removed chlorophyll A and carotenoids pigments significantly. In addition, about 50% of total tocopherol content in cold-pressed rapeseed oil was reduced by bleaching. Originally total tocopherol content was 46.62mg/100g in cold-pressed rapeseed oil. But after bleaching, total tocopherol content was 12.67mg/100g (20 min bleaching), 15.31mg/100g (40 min bleaching), and 13.56mg/100g (60 min bleaching). However plant sterols content in cold-pressed rapeseed oil remained unchanged by bleaching. Overall, acid-activated clays were useful for the bleaching of pigmented rapeseed oil.

• Journal of Korean Society of Steel Construction
• /
• v.21 no.5
• /
• pp.515-526
• /
• 2009

There are three main production processes in the manufacture of concrete-filled square steel columns. The first process is known as the 'box-type process' or 'four-seam method,' wherein four beams are welded together at the seams. The second is the 'cold-forming process' or 'two-seam method,' wherein the seams of two channel beams are welded together. The third is the 'pressing process' or 'one-seam method,' wherein a circular column is pressed until it becomes a square column. In calculating the production cost for the making of a steel tube, it is very important to consider the welding process to be used and the desiredthickness of the steel tube, such as a square column that was developed under a new method, formed through the four-seam flare welding method at the center of the steel column width, following the L-shape formation. Certain tests were suggested in this study to evaluate the welding amount of concrete-filled square steel columns. With the parameters of the production method of a square steel column, the thickness of the steel square columns, and the welding amount, six specimens were produced. A structural test and finite-element analysis were conducted to assess the behavior of the steel column according to the water pressure inside the steel columns.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.4
• /
• pp.333-340
• /
• 2019

The effects of compaction methods on the sintering density, microstructures, and mechanical properties were investigated in ${\alpha}-alumina$ ceramics. ${\alpha}-Alumina$ powders were granulated with a 10% aqueous solution of polyvinyl alcohol (PVA). Uniaxially pressed (UAP) and cold isostatic-pressed (CIP) samples were prepared by pressing uniaxially at a pressure of 1 ton for 1 min, and isostatically at 200 MPa for 15 min, respectively. Subsequently, both types of samples were sintered at $1,200^{\circ}C$, $1,300^{\circ}C$, $1,400^{\circ}C$, $1,450^{\circ}C$, $1,500^{\circ}C$, $1,550^{\circ}C$, and $1,600^{\circ}C$ at a rate of $5^{\circ}C/min$ for 2 h. The CIP samples were better than the UAP samples for all properties measured, such as the sintering density, Vicker's hardness, and toughness. The CIP sample sintered at $1,400^{\circ}C$ showed the maximum Vicker's hardness and toughness; this may be attributed to the competing effects of a decrease in porosity and the growth of grains with increasing sintering temperature.

• The Journal of Internal Korean Medicine
• /
• v.21 no.1
• /
• pp.169-180
• /
• 2000

Objectives : To satisfy the demand of good treatment of constipation Methods : we investigated the literatures of Oriental Medicine about Constipation. Results: 1. There are three categories of etimological factors of constipation, that is, endogenous, exogenous and non-exo-endogenous factor. The endogenous factor is caused by seven emotions, called depression of Ki and stagnation of Ki. The exogenous factor is six excessive atmospheric influences, for example, wind, cold, dampness, heat and dryness. And the non-exo-endogenous factors are overfatigue, improper diet, stagnated blood and deficiency of Ki and blood that comes from old age, long disease and after delivery. 2. Classification: According to cause of disease it is classified by constipation due to cold, heat, wind, dryness, retention of undigested and phlegm. According to Internal Organs there are constipation due to deficiency syndrome of the stomach, excess syndrome of the stomach, deficiency syndrome of kidney and splenic constipation. And Differentiation of syndromes according to Ki and blood, there are constipation of deficiency type and excess type. There are constipation due to stagnation and deficiency of Ki, deficiency of blood and stagnated blood. 3. Principles and Methods of treatment 1) Herbal Medicine (1) Excess type [1] Constipation due to heat : Seunggitang(承氣湯) and Majainwhan(麻子仁丸) [2] Constipation due to stagnation of Ki : Samatang(四磨湯) and Yukmatang(六磨湯) (2) Deficiency type [1] Constipation due to deficiency of Ki : Whanggitang(黃?湯) [2] Constipation due to deficiency of blood: Yunjangwhan(潤腸丸) [3] Constipation due to cold : Jechunjun(濟川煎) and Banyuwhan(半硫丸) 2) Enema therapy: It is a method to induce defecation by honey or pig's bile juice for weak people. 3) Acupuncture and Moxibustion: Acupoints used to treat constipation are BL25, ST25 and TE6. Moxibustion at CV8, CV6 is good for constipation due to cold. (4) Diet therapy: It is very important that we eat meals regularly and defecate on the same time even if you don't. And we have to eat food like fruits, vegetables and beans. (5) finger pressure: Finger pressing around these points like ST25, SP25, BL25, BL31, BL32, BL33 and BL34 is good for it. (6) Kigong therapy: Abdominal breathing (7) Old man' s constipation: Hip bath or diet therapy is commended. Laxation with lubricant like Supungyunjangwhan(搜風潤腸丸) is used. (8) Women' s constipation: After delivery, we have to administer tonifying prescription Sipjundaebotang(十全大補湯) and enema can be used. Conclusion : We have to examine the cause of disease and bowl movement carefully. After comprehensive analysis of the data gained by the four methods of diagnosis, we diagnose and treat patients on the base of overall of symptoms and signs.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1051-1053
• /
• 1995

Nowadays perovskite $La_{1-x}Sr_xMnO_3$ is preferred cathode material in Solid Oxide Fuel cell(SOFC). The $La_{1-x}Sr_xMnO_3$ with Sr contents ranging $x=0{\sim}1.0$ were prepared by a citrate method. These powders were characterized by usual means like TG/DTA, X-ray diffraction analysis. The samples used for measuring thermal expansion were prepared as pellets by cold pressing and subsequent sintering in air at $1200^{\circ}C$ for 5 hours. To measure the by-product of $La_{1-x}Sr_xMnO_3$ reacted with 8mol% YSZ, that samples were sintered at $1200^{\circ}C$ for 5 hours.

• Journal of the Korean Applied Science and Technology
• /
• v.30 no.3
• /
• pp.551-559
• /
• 2013

To investigate the adhesion effect of sodium bisulfite content in making blocked isocyanate, wood adhesive PB-1, PB-2, PB-3 and PB-4 containing sodium bisulfite content of 15%, 22.5%, 30% and 37.5% were synthesized respectively. As a result, when the amount of sodium bisulfite increased in adhesives, the tensile strength was found to be proportionally increased. The final adhesive mixtures were manufactured using a two-components system which are prepared by mixing two separate protein and BI solutions due to the precipitate in the adhesives. As PVA was added to adhesives to increase tenacity, the plywood dehiscence phenomenon after cold pressing process was declined. By addition of PVA, the tensile strength was improved up to $6.5{\sim}7kgf/cm^2$ with BI/protein ratio from 1:6 up to 1:8. Phase separation between milk fat and aqueous layer was disappeared after addition of emulsifier, Tween 20. Additon of Tween 20 showed tensile strength up to $5{\sim}6.5 kgf/cm^2$ at NCO/protein ratio of 1:12 ~ 1:14 without phase separation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.3
• /
• pp.269-274
• /
• 2002

(Sm/Y)-Ba-Cu-O system high Tc composite superconductors with/without $CeO_2$ additive were directionally grown by zone-melting process, haying large temperature gradient, In air atmosphere. Cylindrical green rods of $({Sm/y})_{1.8}Ba_{2.4}Cu_{3.4}O_x$ [(Sm/Y)1.8] composite oxides by cold isostatic pressing(CIP) method using rubber mold were fabricated. The microstructure and superconducting properties were investigated by XRD, SEM, TEM and SQUID magnetometer. The size of nonsuperconducting $({Sm/y})_2BaCuO_5$ inclusions of the melt-textured (Sm/Y)1.8 sample with CeO$_2$ additive were remarkably reduced and uniformly distributed within the superconducting (Sm/Y)1.8 matrix. Both samples, with/without $CeO_2$ additive, showed an onset Tc $\geq$ 90 K and sharp superconducting transition. The critical current density Jc value of the $CeO_2$ addictive were $1{\times}10^5A/\textrm{cm}^2$ in 77 K, 0 Tesla.