• Proceedings of the Korean Society of Food Hygiene and Safety Conference
• /
• 2001.10a
• /
• pp.37-43
• /
• 2001

• Journal of the Korean Chemical Society
• /
• v.61 no.4
• /
• pp.143-150
• /
• 2017

Countercurrent oxidation process (COP) was developed and evaluated for treatment of highly concentrated PCB containing insulating oil. The PCB content in insulating oil taken from Haksanmetal company was found to be 1,512 ppm. The COP utilizes a self-sustained flame which propagates itself in a direction counter to the oxygen flow. The flame removes PCBs adsorbed in activated carbon and, at the same time, regenerates activated carbon. The flame temperature was determined from both mass loss of activated carbon and the relative ratio of CO and $CO_2$ exhausted during COP, and showed that its temperature lied in the range of $650-850^{\circ}C$. Removal efficiency of PCBs was achieved above 99.99% for 5% of insulating oil loaded activated carbon with 1 COP in weight ratio. Also, the same removal efficiency was acquired for 60% of insulating oil loaded activated carbon with three consecutive COP. In addition, specific surface area of activated carbon during COP was recovered to almost similar value of virgin activated carbon. It proved that the COP was much effective in removing high concentration of PCBs in insulating oil easily and affordably.

• Proceedings of the Korea Society of Environmental Toocicology Conference
• /
• 2003.05a
• /
• pp.166-166
• /
• 2003

In terms of the risk assessment, qualitative and quantitative informations are needed to estimate the exposures of environmental pollutants, which may be potentiality of risks, and those are the information about the changes caused by the chemical transportation among environmental media and transformation in environmental media by duration. The various fate mechanism of chemical is possible for estimation of chemical concentration in environmental media. Since there are limitations in measuring the change of chemical concentration within all medium according to the time period, estimating method through modeling are developed.

• Clean Technology
• /
• v.15 no.1
• /
• pp.9-15
• /
• 2009

Catalytic hydrodechlorination of PCBs (polychlorinated biphenyls) included in the transformer oil was carried out to detoxify PCBs and to recycle the treated oil. Catalysts such as 0.98 wt% Pt and 0.79 wt% Pd on ${\gamma}$-alumina (${\gamma}-Al_2O_3$) support, 12.8 wt% Ni on ${\gamma}-Al_2O_3$, and 57.6 wt% Ni on silica-alumina ($SiO_2-Al_2O_3$) support were used for the catalytic hydrodechlorination. Various supercritical fluids such as carbon dioxide, propane and isobutane were used as reaction media. The effects of reaction temperature, reaction time, catalysts, and supercritical fluids on the catalytic hydrodechlorination were examined in detail. The detoxification degree increased in the order of Ni > Pd > Pt. This is possibly due to higher metal loading and larger metal size of the Ni catalyst. Below $175^{\circ}C,\;scCO_2$ was found as the most effective reaction media for the catalytic hydrodechlorination of PCBs included in the transformer oil.

• Journal of Microbiology
• /
• v.41 no.3
• /
• pp.189-195
• /
• 2003

To enhance the reductive dechlorination of polychlorinated biphenyls (PCBs) under anaerobic conditions, we examined the adjunctive effects of cobalt (Co) and nickel (Ni), which are the central metals of transition-metal cofactors of coenzyme F$\_$430/ and vitamin B$\_$12/, respectively, on the dechlorination of Aroclor 1248. After 32 weeks of incubation, the average numbers of chlorines per biphenyl in culture vials supplemented with 0.2, 0.5, and 1.0 mM of Co reduced from 3.88 to 3.39, 2.92, and 3.28, respectively. However, the numbers of chlorine after supplementing with Ni decreased from 3.88 to 3.43, regardless of the Ni concentrations. The observed congener distribution patterns of all vials with different conditions were similar to the pattern produced by the dechlorination process of H' after 21 weeks of incubation, and these patterns were unchanged up to week 32, except for vials supplemented with 0.5 and 1.0 mM of Co. In vials containing 0.5 mM of Co, meta-rich congeners, such as 25/ 25-,24/25-, and 25/23-chlorobiphenyls (CBPs), which were found as accumulated products of dechlorination in other conditions, were further dechlorinated, and 25/2-, 24/2-, and 2/2-CBPs were concomitantly increased after 32 weeks of incubation. In this case, the congener distribution was similar to the dechlorination pattern of process M. From these results, we suggested that the enrichment of cultures with Co might stimulate the growth of specific populations of meta-dechlorinators, and that populations might promote a change in the dechlorination process from H' to M, which is known to be less effective on the dechlorination of the more highly chlorinated congeners of PCBs.

• Microbiology and Biotechnology Letters
• /
• v.34 no.2
• /
• pp.174-179
• /
• 2006

Bacterium capable of using biphenyl as a sole source of carbon and energy were isolated from soil, and based on the results of 16S rDNA sequence, strain BK10 identified as a Sphingobium yanoiktiyae. The optimum cultural conditions were as follows; $NH_4NO_3$ 1g, $K_2HPO_4$ 1g, $MgSO_4{\cdot}7H_2O$ 0.5g, $CaCO_3$ 0.2 g per 1 liter of distilled water. The Sphingobium yanoikuyae BK10 strain was completely utilized biphenyl in mineral salt media containing biphenyl at concentration 500 $\mu$g/ml of biphenyl as a sole carbon and energy source within 48 hours. Optimumal pH and temperature for biphenyl degradation and cell growth of strains were 6.0$\sim$8.0 and 20$\sim$50$^{\circ}C$, respectively. Especially, at 30$^{\circ}C$, cell-growth were higher than other temperature. Cell grown on biphenyl has been shown to have a higher removal rate for biphenyl than grown on sucrose. This study shows that Sphingobium yanoikuyae BK10 strain had a high biodegradation capability of biphenyl and can be simulate a candidate compounds the bioremediation of PCBs (Polychlorinated biphenyl) contaminant soil and water.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.12 no.3
• /
• pp.320-330
• /
• 2012

In this paper, we investigate the power integrity of grid structures for power and ground distribution on printed circuit board (PCB). We propose the 2D transmission line method (TLM)-based model for efficient frequency-dependent impedance characterization and PCB-package-integrated circuit (IC) co-simulation. The model includes an equivalent circuit model of fringing capacitance and probing ports. The accuracy of the proposed grid model is verified with test structure measurements and 3D electromagnetic (EM) simulations. If the grid structures replace the plane structures in PCBs, they should provide effective shielding of the electromagnetic interference in mobile systems. An analytical model to predict the shielding effectiveness (SE) of the grid structures is proposed and verified with EM simulations.

• Journal of Korean Society on Water Environment
• /
• v.24 no.6
• /
• pp.758-766
• /
• 2008

To evaluate homologue patterns and removal efficiency before and after water treatment, the concentrations of dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs) and coplanar polychlorinated biphenyls (Co-PCBs) were determined in 122 samples from 42 drinking water treatment plants throughout Japan over a two year period. The mean concentrations and toxic equivalent (TEQ) values of dioxins in raw and treated waters were 60.24 pg/L (0.14 pg-WHO-TEQ/L) and 4.15 pg/L (0.016 pg-WHO-TEQ/L), respectively. The dioxins contribution ratio of drinking water in relation to dioxins tolerable daily intake (TDI, 4 pg-TEQ/kg/day) was 0.016%. The mean TEQ removal rate of dioxins by drinking water treatment was over 88%. However, the mean removal rate of 2, 3, 7, 8-TeCDF (tetrachlorodibenzofuran) by water treatment in the 122 samples was minus 17%. Therefore, to identify which process affected the level of 2, 3, 7, 8-TeCDF, the removal efficiencies at both the advanced and conventional water treatment plants were investigated. For the TEQ removal rate across the processes, the dioxin congeners, TeCDF and non-ortho-PCBs remarkably indicated minus values after chlorination in both the advanced and conventional water treatments plant. From this study, the level of 2, 3, 7, 8-TeCDF was found to be increased as a result of chlorination.

• Analytical Science and Technology
• /
• v.14 no.1
• /
• pp.88-93
• /
• 2001

To measure the levels of dioxins in food selling at local markets, meat was analyzed by high resolution gas chromatography/high resolution ass spectrometry (HRGC/HRMS). The food samples were obtained from 5 large cities of Seoul, Chunchon, Daejon, Kwangju and Busan in Korea. All the samples were minced and extracted with Soxhlet extractor for 18 hours. After extraction, extracts were cleaned up by sulfuric acid impregnated silica gel, purified on a series of silica gel, alumina, carbon column chromatography and then analyzed by HRGC/HRMS. The contaminated levels were calculated as the TEQs by multiplying with the corresponding WHO-TEFs for each congeners. The overall recoveries were ranged from 80% to 153% and the limit of detection was about 0.01 ppt at S/N>3. The levels of PCDD/Fs for beef, pork and chicken were 0.018, 0.008 and <0.001 pgTEQ/g, respectively. In addition, the levels of non-ortho-co-planar PCBs for beef, pork and chicken were 0.008, 0.002 and 0.001 pgTEQ/g, respectively. Among food samples analyzed, chicken showed the lowest level of dioxin-like compounds. Regarding congener pattern, OCDD and PCB #77 were the highest contributing congeners.

• Journal of IKEEE
• /
• v.23 no.4
• /
• pp.1473-1476
• /
• 2019

Accurate material information is very important in PCB (Printed Circuit Board) design. In an integrated mast of a battleship, heat reduction is essential for stealth functionality. So heat dissipation from internal control equipments should be reduced as much as possible. Control equipments mostly consist of PCBs, but it often suffers from impedance mismatching due to imprecise Dk (Dielectric Constant), which significantly increases heat dissipation. In this paper, measurement methods of Dk is investigated. Also, effects on impedance mismatch by Dk variation with operating frequency is investigated.