• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.2
• /
• pp.389-396
• /
• 1988

Microprocessor-based software DDA interpolator is developed and applied to two axis contouring control of X-Y table. Developed assembly program is composed of feedrate, linear and circular DDA interpolation routines. Reference-pulse type of open-loop stepping motor control system in which the micro-computer produces a sequence of reference pulses for each axis of motion is adopted. To test performance of the developed program, X-Y table drive system based on stepping motor and shaft encoder is designed. Conturing error of the system in linear and circular path is within .+-. 0.2mm under start stop pulse rate of stepping motor.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.378-381
• /
• 2003

Efficient development of method on a performance evaluation for machine tools has been regarded as the most important work for accuracy and quality enhancement to every user and manufacturer. A evaluation method of accuracy for machine tools has been studied recently according to the rapid increase of interest in precision machine tools. To this point of view, the circular interpolation test of machine tools is recognized as the most useful method to distinguish a dynamic accuracy of NC machine tools by ISO and ANSI/ASME, etc. In this paper, we have studied and developed the form measurement system with grid encoder to analyse the final accuracy of NC machine tools. we have analyzed the servo system error and geometric error of NC machine tools through measuring a dynamic error signal by this system. and then we verified the experimental result and enhanced the reliability by means of comparing the characteristics of the developed system with the kinematic ball-bar system.

• Proceedings of the KIEE Conference
• /
• 1993.07a
• /
• pp.391-394
• /
• 1993

The acceleration/deceleration control method and interpolated operating are essential to the servo motor control system. In a few years ago, a floating point DSP chip was used for the purpose of processing a lot of calculated amount. But in this paper, we proposed new acceleration/deceleration control method and circular interpolation algorithm without another floating point DSP chip. The validity of proposed algorithms are verified through computer simulation and experimental result.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• v.28 no.2
• /
• pp.59-70
• /
• 2024

In this paper we present the approximation method of the circular helix by G² cubic polynomial curves. The approximants are G¹ Hermite interpolation of the circular helix and their approximation order is four. We obtain numerical examples to illustrate the geometric continuity and the approximation order of the approximants. The method presented in this paper can be extended to approximating the elliptical helix. Using the property of affine transformation invariance we show that the approximant has G² continuity and the approximation order four. The numerical examples are also presented to illustrate our assertions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.4
• /
• pp.141-150
• /
• 1998

The measurement of strains in stamped sheet metal is essential to the design and manufacture of sound sheet metal products. The measured strains can also be used in verifying the reliability of the computer analysis such as finite element analysis. In most engineering applications, strains are measured from the deformed square grids or deformed circular grids in comparison with the initial undeformed grids. In such a case, however, strains are averaged in each grid and the localized strain in a region smaller than a grid size can not be measured. In the present study, the B-spline surface interpolation technique is introduced in order to measure the strains more exactly and effectively. The strains calculated by using the surface interpolation technique are compared with the strains calculated from the three-noded grids as well as with the finite element analysis.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.12
• /
• pp.99-105
• /
• 1996

Increasing demands on precision machining of free-form surfaces have necessitated the tool to move not only with position error as small as possible, but also with smoothly varying feedrates. In this paper, linear, circular and spline interpolators were developed in reference-pulse type using PC. M-SAM and M-DAM were designed by the comparison and analysis of previous interpolation methods. Spline interpolator was designed to follow the free-form curves. To apply to the real cutting process, constant feedrate compensation and acceleration-deceleration compensation were conceived. Finally, its performance was tested using retrofitted milling machine. As a result, new interpolation algorithm is favorable in precision machining of free-form curves.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.2
• /
• pp.243-253
• /
• 1999

The dual reciprocity boundary element method (DRBEM) is used to solve the Graetz problem of laminar flow inside circular duct. In this method the domain integral tenn of boundary integral equation resulting from source term of governing equation is transformed into equivalent boundary-only integrals by using the radial basis interpolation function, and therefore complicate domain discretization procedure Is completely removed. Velocity profile is obtained by solving the momentum equation first and then, using this velocities as Input data, energy equation Is solved to get the temperature profile by advancing from duct entrance through the axial direction marching scheme. DRBEM solution is tested for the uniform temperature and heat flux boundary condition cases. Local Nusselt number, mixed mean temperature and temperature profile inside duct at each dimensionless axial location are obtained and compared with exact solutions for the accuracy test Solutions arc in good agreement at the entry region as well as fully developed region of circular duct, and their accuracy are verified from error analysis.

• 제어로봇시스템학회:학술대회논문집
• /
• 1987.10b
• /
• pp.228-231
• /
• 1987

Microprocessor-based software DDA interpolator is developed and applied to two axis contouring control of X-Y table. Developed assembly program is composed of feedrate, linear and circular DDA interpolation routines. Reference-pulse type of open-loop stepping motor control system in which the micro-computer produces a sequence of reference pulses for each axis of motion is adopted. To test performance of the developed program, X-Y table drive system based on stepping motor and shaft encoder is designed. Contouring error of the system in linear and circular path is within .+-.0.2 mm.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.975-978
• /
• 2001

For machining auto-mobile cam, the developed biarcs-fitting method eliminates the ridge problems in conventional straight-line fitting approximation or single-arc fitting of curve tool path where it leaves ridges of tool marks on the machined surface of the workpiece. The powerful advantage of this biarc method is demonstrated by applying it to the numerically controlled machining of a curved cam profile, also verified by using a CNC simulating program for auto-mobile cam profile. As a result, this algorithm may be used in CNC milling and turning for cam profile machining with short block line.

• Journal of Power System Engineering
• /
• v.5 no.2
• /
• pp.43-49
• /
• 2001

For machining auto-mobile cam, the developed biarcs-fitting method eliminates the ridge problems in conventional straight-line fitting approximation or single-arc fitting of curve tool path where it leaves ridges of tool marks on the machined surface of the workpiece. The powerful advantage of this biarc method is demonstrated by applying it to the numerically controlled machining of a curved cam profile, also verified by using a CNC simulating program for auto-mobile cam profile. As a result, this algorithm may be used in CNC milling and turning for cam profile machining with short block line.