• 전력전자학회논문지
• /
• 제25권6호
• /
• pp.477-483
• /
• 2020

This study proposes a DQ synchronous reference frame model of a series-parallel tuned inductive power transfer (SP-IPT) system. The wireless power transmission system experiences control difficulty because the transmitter-side controller cannot directly measure the receiver-side load voltages and currents. Therefore, a control-oriented circuit model that shows the dynamics of the IPT system is required to achieve a well-behaved controller. In this study, an equivalent circuit model of the SP-IPT system in a synchronously rotating reference frame is proposed using the single-phase DQ transformation technique. The proposed circuit model is helpful in modeling the dynamics of the voltages and currents of the transmitter- and receiver-side resonant tanks and loads. The proposed circuit model is evaluated using frequency- and time-domain simulation results.

• Journal of Advanced Marine Engineering and Technology
• /
• 제41권3호
• /
• pp.258-268
• /
• 2017

본 논문에서는 하나의 해석 소프트웨어(SimulationX)로 로딩암의 유압회로 해석기술과 다물체 동역학 해석기술을 융합시키는 것을 목표로 한다. 움직이는 질량의 회전중심에 변화가 있거나, 중력장에서의 거동을 구현하기 어려운 기존의 유압회로해석기술의 한계성을 극복하고자 하는 연구이다. 연구를 진행하는 순서는 다음과 같다. 먼저 유압회로를 구성하는 부품들의 제원을 해석모델에 반영하여 신뢰성을 확보한다. 신뢰성이 검증된 단품해석모델을 이용하여 유압회로를 모델링하고, 로딩암의 MBS(Multi Body System)모델을 구성한다. 그 후에 유압회로의 해석모델과 MBS모델을 융합하여 회로의 해석결과가 MBS모델에 정확히 반영되는지 확인한다. 이러한 융합해석모델은 시제품이 없어도 대상의 동적거동을 예측 할 수 있으므로 개발비를 절감하는 효과를 가져다준다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권7호
• /
• pp.339-342
• /
• 2005

We present a new high-frequency equivalent circuit model for 52pin QFP used in typical IC's and extract R, L, and C values of this circuit model using a 3-D E & M field simulator. Futhermore, L and C value variations as a function of Pin number due to the shape differences of the leads have been fitted to 2nd order polynomials in order to extend the applicability of this model.

• Transactions on Electrical and Electronic Materials
• /
• 제5권1호
• /
• pp.19-23
• /
• 2004

A novel method of high speed, accurate circuit simulation in 3-dimensional (3-D) parallel-plate capacitors is investigated. The basic concept of the circuit simulation methods is partial element equivalent circuit model. The three test structures of 3-D parallel-plate capacitors are fabricated by using multi-layer low-temperature co-fired ceramic (LTCC) process and their S-parameters are measured between 50 MHz and 5 GHz. S-parameters are converted to Y-parameters, for comparing measured data with simulated data. The circuit model parameters of the each building block are optimized and extracted using HSPICE circuit simulator. This method is convenient and accurate so that circuit design applications can be easily manipulated.

• 전기학회논문지
• /
• 제62권1호
• /
• pp.70-75
• /
• 2013

The electrical separation joint as a filter circuit distributes the track circuit frequency. The electrical separation joint is classified into the interval where reinforcing bars are insulated and not insulated through the length of track circuit. In case of incorrectly setting up the length of electrical separation joint, the amplitude of current on the track circuit is not over standard current which is the standard of current on the track circuit and it effects on the close frequency on track circuit. Then, it makes an accident or makes a train not receive information for train control. In this paper, the electrical separation joint model is suggested and parameters are numerically calculated in the model. Moreover, the length of electrical separation joint is analyzed and is demonstrated by uisng Matlab and PSpice program.

• 대한전기학회논문지
• /
• 제34권11호
• /
• pp.440-444
• /
• 1985

Voltage equations of a synchronous machine are derived from the electromagnetic field theory in order to develop a new equivalent circuit model considering core loss. The result from the new equivalent circuit model is superior to that of the conventional one in the analysis of machine performance and characteristics on optimal efficiency control of a synchronous motor.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제15권5호
• /
• pp.463-469
• /
• 2015

A vibration-based energy harvester and its equivalent circuit models have been reported. Most models predict voltage signals at harmonic excitation. However, vibrations in a natural environment are unpredictable in frequency and amplitude. In this paper, we propose a realistic equivalent circuit model of a frequency-up-converting impact-based piezoelectric energy harvester. It can describe the behavior of the harvester in a real environment where the frequency and the amplitude of the excitation vary arbitrarily. The simulation results of the model were compared with experimental data and showed good agreement. The proposed model can predict both the impact response and long term response in a non-harmonic excitation. The model is also very useful to analyze the performance of energy conversion circuitry with the harvester.

• Journal of Power Electronics
• /
• 제18권6호
• /
• pp.1901-1911
• /
• 2018

This study presents a circuit model for simulating the switching transients of insulated-gate bipolar transistors (IGBTs) with inductive load switching. The modeling approach used in this study considers the behavior of IGBTs and freewheeling diodes during the transient process and ignores the complex semiconductor physics-based relationships and parameters. The proposed circuit model can accurately simulate the switching behavior due to the detailed consideration of device-circuit interactions and the nonlinear nature of model parameters, such as internal capacitances. The developed model is incorporated in an IGBT loss calculation module of an electromagnetic transient simulation program to enable the estimation of switching losses in voltage source converters embedded in large power systems.

• KEPCO Journal on Electric Power and Energy
• /
• 제6권4호
• /
• pp.473-480
• /
• 2020

In this paper, we proposed a high frequency equivalent circuit considering parasitic impedance components for differential noise analysis on the input stage during DC-DC buck converter switching operation. Based on the proposed equivalent circuit model, we presented a method to measure parasitic impedance parameters included in DC bus plate, IGBT, and PCB track using the gain phase method of a network analyzer. In order to verify the validity of this model, a DC-DC prototype consisting of a buck converter, a signal analyzer, and a LISN device, and then resonance frequency was measured in the frequency range between 150 kHz and 30 MHz. The validity of the parasitic impedance measurement method and the proposed equivalent model is verified by deriving that the measured resonance frequency and the resonance frequency of the proposed high frequency equivalent model are the same.

• Journal of Power Electronics
• /
• 제13권6호
• /
• pp.1008-1015
• /
• 2013

By using fractional calculus and the circuit-averaging technique, the modeling and analysis of a Buck converter with fractional order inductor and fractional order capacitor in discontinuous conduction mode (DCM) operations is investigated in this study. The equivalent averaged circuit model of the fractional order Buck converter in DCM operations is established. DC analysis is conducted by using the derived DC equivalent circuit model. The transfer functions from the input voltage to the output voltage, the duty cycle to the output voltage, the input impedance, and the output impedance of the fractional order Buck converter in DCM operations are derived from the corresponding AC-equivalent circuit model. Results show that the DC equilibrium point, voltage ratio, and all derived transfer functions of the fractional order Buck converter in DCM operations are affected by the inductor order and/or capacitor order. The fractional order inductor and fractional order capacitor are designed, and PSIM simulations are performed to confirm the correctness of the derivations and theoretical analysis.