• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.162-162
• /
• 2008

세리아는 고체 산화물 연료전지(SOFC, solid oxide fuel cell)의 전해질 재료와CMP( chemical mechanical polishing) 슬러리 재료, 자동차의 3원 촉매, gas sensor, UV absorbent등 여러 분야에서 사용되고 있다. 본 연구에서는 세리아의 입자의 크기와 형상을 조절하여 성능 및 물성을 향상시켜 보다 넓은 분야의 활용을 하고자 실험을 실시하였다. 세리아 합성에 사용되는 전구체인 cerium carbonate의 특성이 세리아 분말의 물리화학적 특성에 직접적인 영향을 주기 때문에 전구체의 합성 단계에서 형상과 크기를 조절하고자 하였다. 세륨염으로 cerium nitrate hexahydrate, 균일침전반응을 할 수 있는 urea를 침전제로 사용하였다. 반응 용매의 유전상수를 조절하고 반응의 과포화도 변화를 이용하기 위하여 에탄올을 첨가하여 입자의 크기 및 형상을 조절, cubic형태의 $Ce_2O(CO_3)_2{\cdot}H_2O$ 결정상을 가지는 세리아 전구체를 합성하였다. 이렇게 생성된 전구체를 $1000^{\circ}C$에서 2시간동안 하소하여 세리아를 합성하고 반응시간, 농도, 에탄올의 함량 변화에 대해 XRD, FE-SEM, particle size analyzer, micropore physisorption analyzer 분석을 통하여 입자의 결정상과 형상, 입도 분포 및 기공분포 등을 반응인자의 변화에 따라 비교 및 해석하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.171-175
• /
• 2001

Chemical mechanical polishing(CMP) process has been widely used to planarize dielectrics and metal, which can apply to employed in integrated circuits for sub-micron technology. Despite the increased use of CMP process, it is difficult to accomplish the global planarization of free-defects in inter level dielectrics and metal. Especially, defects like (micro-scratch) lead to severe circuit failure, and affects yield. Current conditioning method - bladder type, orbital pad motion- usually provides unsuitable pad profile during ex-situ conditioning near the end of pad life. Since much of the pad wear occurs by the mechanism of bladder type conditioning and its orbital motion without rotation, we need to implement new ex-situ conditioner which can prevent abnormal regional force on pad caused by bladder-type and also need to rotate the pad during conditioning. Another important study of ADPC is related to the orbital scratch of which source is assumed as diamond grit dropped from the strip during ex-situ conditioning. Scratch from diamond grit damaged wafer severely so usually scraped. Figure 1 shows the typical shape of scratch damaged from diamond. e suspected that intensive forces to the edge area of bladder type stripper accelerated the drop of Diamond grit during conditioning. so new designed Flat stripper was introduced.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.3
• /
• pp.175-184
• /
• 2001

In this study, the improved throughput and stability in device fabrication could be obtained by applying CMP process to STi structue in 0.18 um semiconductor device. To employ the CMP process in STI structure, the Reverse Moat Process used to be added after STI Fill, as a result, the process became more complex and the defect were seriously increased than they had been,. Removal rate of each thin film in STI CMP was not uniform, so, the device must have been affected. That is, in case of excessive CMP, the damage on the active area was occurred, and in the case of insufficient CMP nitride remaining was happened on that area. Both of them deteriorated device characteristics. As a solution to these problems, the development of slurry having high removal rate and high oxide to nitride selectivity has been studied. The process using this slurry afford low defect levels, improved yield, and a simplified process flow. In this study, we evaluated the 'High Selectivity Slurry' to do a global planarization without reverse moat step, and also we evaluated EPD(Eend Point Detection) system with which 'in-situ end point detection' is possible.

• Proceedings of the KIEE Conference
• /
• 2006.10a
• /
• pp.105-106
• /
• 2006

The ferroelectric materials of the PZT, SBT attracted much attention for application to ferroelectric random access memory (FRAM) devices. Through the last decade, the lead zirconate titanate (PZT) is one of the most attractive perovskite-type materials for the ferroelectric products due to its higher remanant polarization and the ability to withstand higher coercive fields. FRAM has been currently receiving increasing attention for one of future memory devices due to its ideal memory properties such as non-volatility, high charge storage, and faster switching operations. In this study, we first applied the damascene process using chemical mechanical polishing (CMP) to the fabricate the $Pb_{1.1}(Zr_{0.52}Ti_{0.48})O_3$ thin film capacitor in order to solve the problems of plasma etching such as low etching profile and ion charging. The structural characteristics were compared with specimens before and after CMP process of PZT films. The scanning electron microscopy (SEM) analysis was performed to compare the morphology surface characteristics of $Pb_{1.1}(Zr_{0.52}Ti_{0.48})O_3$ capacitors. The densification by the vertical sidewall patterning and charging-free ferroelectric capacitor could be obtained by the damascene process without remarkable difference of the characteristics.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.149-153
• /
• 2003

Chemical mechanical polishing (CMP) technology for global planarization of multi-level inter-connection structure has been widely studied for the next generation devices. CMP process has been paid attention to planarized pre-metal dielectric (PMD), inter-layer dielectric (ILD) interconnections. Expecially, shallow trench isolation (STI) used to CMP process on essential. Recently, the direct STI-CMP process without the conventional complex reverse moat etch process has established by using slurry additive with the high selectivity between $SiO_2$ and $Si_3N_4$ films for the purpose of process simplification and n-situ end point detection(EPD). However, STI-CMP process has various defects such as nitride residue, tom oxide and damage of silicon active region. To solve these problems, in this paper, we studied the planarization characteristics using a high selectivity slurry(HSS). As our experimental results, it was possible to achieve a global planarization and STI-CMP process could be dramatically simplified. Also we estimated the reliability through the repeated tests with the optimized process conditions in order to identify the reproducibility of HSS STI-CMP process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.162-165
• /
• 2003

The corrosion characteristics of diffusion barrier in Copper CMP has been investigated. Key experimental variables that has been investigated are the corrosion rate by different agents containing slurry of Cu CMP. Whenever Cu and Ta films were corroded adding each oxidizer, the corrosion rate of Ta was much lower than that of Cu. That is, the difference in the corrosion rates of Ta by oxidizer was not larger as compared with Cu. As corroded by complexing agents, the corrosion rate of Ta was close to O. The corrosion rate of Ta increased as added $HNO_3$ and $CH_3COOH$ compared with the reference slurry; on the other hand, it decreased with addition of HF. In addition, resulting corrosion rate went up with lower pH of agent. The corrosion rates by agents were however significant small; hence, it doesn't affect on the removal rate of Cu CMP practically. Consequently, this can be explained by assuming that the mechanical effect dominates than the chemical effect on the polishing rate of Ta(TaN).

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1450-1451
• /
• 2006

In this paper, we first applied the chemical mechanical polishing (CMP) process to the planarization of ferroelectric film in order to obtain a good planarity of electrode/ferroelectric film interface. $Bi_{3.25}La_{0.75}Ti_{3}O_{12}$ (BLT) ferroelectric fan was fabricated by the sol-gel method. Removal rate and non-uniformity (WIWNU%) were examined by change of silica slurries pH(10.3, 11.3, 12.3). Surface roughness of BLT thin films before and after CMP process was inquired into by atomic force microscopy (AFM). Effects of silica slurries pH(10.3, 11.3, 12.3) were investigated on the CMP performance of BLT film by the surface analysis of X-ray photoelectron spectroscopy(XPS).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.90-93
• /
• 2000

In this study, the rise throughput and the stability in fabrication of device can be obtained by applying of CMP process to STI structure in 0.18um semiconductor device. To employ in STI CMP, the reverse moat process has been added thus the process became complex and the defects were seriously increased. Removal rates of each thin films in STI CMP was not equal hence the devices must to be effected, that is, the damage was occured in the device dimension in the case of excessive CMP process and the nitride film was remained on the device dimension in the case of insufficient CMP process than these defects affect the device characteristics. To resolve these problems, the development of slurry for CMP with high removal rate and high selectivity between each thin films was studied then it can be prevent the reasons of many defects by reasons of many defects by simplification of process that directly apply CMP process to STI structure without the reverse moat pattern process.

• Transactions on Electrical and Electronic Materials
• /
• v.4 no.6
• /
• pp.28-31
• /
• 2003

Copper CMP in terms of the effect of slurry chemicals (oxidizer, corrosion inhibitor, complexing agent) on the process characteristics has been performed. Corrosion inhibitors, benzotriazole (BTA) and tolytriazol (TTA) were used to control the removal rate and avoid isotropic etching. When complexing agent is added with H$_2$O$_2$ 2 wt% in the slurry, the corrosion rate was presented very well. In the case of complexing agent, it was estimated that the proper concentration is 1 wt%, because the addition of tartaric acid to alumina slurry causes low pH and the slurry dispersion stability become unstable. There was not much change of the removal rate. It was assumed that BTA 0.05 wt% is suitable. Most of all, it was appeared that BTA is possible to be replaced by TTA. TTA was distinguished for the effect among complexing agents.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.42-43
• /
• 2005

본 연구에서는 Cu 슬러리에 부식방지제인 BTA를 첨가하여 슬러리내의 과수의 농도, pH 의 변화, 연마입자의 종류에 따라 연마거동에 미치는 영향과 각 chemical 변화에 따른 Cu surface의 변화를 살펴보았다. BTA (Benzotriazole, $C_6H_4C_3H$)를 첨가함으로써 본 연구에서 시행된 pH 와 과수의 변화에 상관없이 Cu-BTA film을 형성하여 Cu의 dissolution을 최대한 억제하는 것을 확인할 수 있었다. 또 그로인해 BTA를 첨가하지 않았을 때보다 얇은 passivation layer를 형성함을 알 수 있었고 contact angle도 더 높았다. 연마율의 경우에도 BTA가 첨가됨으로써 감소됨을 확인할 수 있었고 연마입자로 alumina particle을 사용한 경우에는 pH6, 과수 10vol%이상에서는 오히려 연마율이 증가하였다. fumed silica의 경우에는 hardness가 작아 mechanical적인 제거력이 낮아 BTA가 첨가되어도 연마율에는 큰 영향이 없었다.