• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 추계학술대회 논문집 Vol.17
• /
• pp.125-128
• /
• 2004

Chemical Mechanical Polishing(CMP) in semiconductor production is characterized its output property by Removal Rate(RR) and Non-Uniformity(NU). Some Previous works shows that RR is determined by production of pressure and velocity and NC is also largely affected by velocity of flow-field during CMP. This study is about the direct measurement of velocity of slurry during CMP and reconstruction whole flow-field by Particle Image Velocimetry(PIV) Techniques. Typical PIV system is tuned adequately for inspecting CMP and Slurry Flow-field is measured by changing both Pad RPM and Carrier RPM. The results show that velocity is majorly determined not by Carrier RPM, but by Pad RPM.

• Design & Manufacturing
• /
• 제13권3호
• /
• pp.48-52
• /
• 2019

As the consumer market in the mold, automation and aerospace industries grows, the demand for chemical machining using on electrochemical polishing increases. To enhance the surface roughness and gloss of the micro-needle, we have studied for an electrochemical polishing. Electrochemical polishing requires the chemical reaction of solution and material according to the electrolyte and electrode. In this study, sulfuric acid(30%), phosphoric acid(50%), and DI-water(20%)were used as the electrolytic solution, and the electrolytic solution temperature used $58^{\circ}C$. Electrochemical polishing was carried out in experimental conditions, and the micro-needle experiment was carried out from the basic experiment to obtain the experimental conditions. Experimental results show that as the voltage and current increase, the surface roughness improved and the gloss is improved. So, the best result for this experiment was obtained in condition 6, which improved micro-needle.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1996년도 제11회 학술발표회 논문개요집
• /
• pp.100-101
• /
• 1996

• 반도체디스플레이기술학회지
• /
• 제6권2호
• /
• pp.35-40
• /
• 2007

An integrated material removal model considering thermal, chemical and contact mechanical effects in CMP process is proposed. These effects are highly coupled together in the current modeling effort. The contact mechanics is employed in the model incorporated with the heat transfer and chemical reaction mechanisms. The mechanical abrasion actions happening due to the mechanical contacts between the wafer and abrasive particles in the slurry and between the wafer and pad asperities cause friction and consequently generate heats, which mainly acts as the heat source accelerating chemical reaction(s) between the wafer and slurry chemical(s). The proposed model may be a help in understanding multi-physical interactions in CMP process occurring among the wafer, pad and various consumables such as slurry.

• 대한화학회지
• /
• 제57권1호
• /
• pp.159-164
• /
• 2013

• 한국정밀공학회지
• /
• 제21권5호
• /
• pp.32-37
• /
• 2004

Polishing processes are widely used in the glass, optical, die and semiconductor industries. Chemical Mechanical Polishing (CMP) especially is becoming one of the most important ULSI processes for the 0.25m generation and beyond. CMP is conventionally carried out using abrasive slurry and a polishing pad. But the surface of the pad has irregular pores, so there is non-uniformity of slurry flow and of contact area between wafer and the pad, and glazing occurs on the surface of the pad. This paper introduces the basic concept and fabrication technique of the next generation CMP pad using micro-molding method to obtain uniform protrusions and pores on the pad surface.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제53권3호
• /
• pp.128-132
• /
• 2004

The perovskite ferroelectric materials of the PZT, SBT and BST series will attract much attention for application to ULSI devices. Among these materials, the BST ($Ba_0.6$$Sr_0.4$/$TiO_3$) is widely considered the most promising for use as an insulator in the capacitors of DRAMS beyond 1 Gbit and high density FRAMS. Especially, BST thin films have a good thermal-chemical stability, insulating effect and variety of Phases. However, BST thin films have problems of the aging effect and mismatch between the BST thin film and electrode. Also, due to the high defect density and surface roughness at grain boundarys and in the grains, which degrades the device performances. In order to overcome these weakness, we first applied the chemical mechanical polishing (CMP) process to the polishing of ferroelectric film in order to obtain a good planarity of electrode/ferroelectric film interface. BST ferroelectric film was fabricated by the sol-gel method. And then, we compared the surface characteristics before and after CMP process of BST films. We expect that our results will be useful promise of global planarization for FRAM application in the near future.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 추계학술대회 논문집 Vol.16
• /
• pp.140-143
• /
• 2003

BST thin films have a good thermal-chemical stability, insulating effect and variety of phases. However, BST thin films have problems of the aging effect and mismatch between the BST thin film and electrode. Also, due to the high defect density and surface roughness at grain boundarys and in the grains, which degrades the device performances. In order to overcome these weakness, we first applied the chemical mechanical polishing (CMP) process to the polishing of ferroelectric film in order to obtain a good planarity of electrode/ferroelectric film interface. BST ferroelectric film was fabricated by the sol-gel method. And then, we compared the structural characteristics before and after CMP process of BST films. We expect that our results will be useful promise of global planarization for FRAM application in the near future.

• 한국전기전자재료학회논문지
• /
• 제13권7호
• /
• pp.568-574
• /
• 2000

We have been optimized tungsten(W) plug CMP(chemical mechanical polishing) characteristics using two different kinds of component of slurry and two different kinds of pad which have different hardness. The comparison of oxide film roughness on around W plug after polishing has been carried out. And W plug recess for consumable sets and dishing effect at dense area according to the rate of over-polishing has been investigated. Also the analysis of residue on surface after cleaning have been performed. As a experimental result we have concluded that the consumable set of slurry A and hard pad was good for W plug CMP process. After decreasing the rate of chemical reaction of silica slurry and adding two step buffering we could reduce the expanding of W plug void however we are still recognizing to need a more development for those kinds of CMP consumables.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.485-485
• /
• 2009

Double side polishing process has been used for various industrial applications, such as polishing of semiconductor substrates and flat panel display glasses. In wafer manufacturing, double side polishing process is applied to improve wafer flatness and to minimize particle generation from wafers in device manufacturing processes, which is recognized as one of the most important processes. Whereas the kinematical modeling and analysis results of single side polishing, extensively used for chemical-mechanical polishing (CMP) in device manufacturing, are well investigated, the studies in conjunction with double side polishing are barely carried out, due to the complication of polishing system and the uncertainty of wafer motion in the carrier. This paper suggests the derivation of kinematical model with consideration of carrier and wafer motion in double side polishing, and then presents the effect of kinematical parameters on material removal amount and its non-uniformity. The kinematical analysis results help to understand the double side polishing process and to control the polishing results.