• Journal of the Korean Ceramic Society
• /
• v.34 no.4
• /
• pp.373-379
• /
• 1997

A study on the deposition and characterization of BaTiO3 thin films on MgO-buffered Si(100) substrates by sputtering was conducted. The MgO buffer layers were investigated as a function of deposition temperature. At lower substrate temperature, the MgO layers were not fully crystalline, but a crystallized MgO layer with (001) preferred orientation was obtained at the substrate temperature of $700^{\circ}C$. Partially (00ι) or (h00) textured BaTiO3 films were obtained on Si(100) with the MgO buffer layer grown at 700ι. While, randomly oriented BaTiO3 films with large-scale cracks on the surface were made without the MgO layer. The crystallographic orientation, morphology and electrical properties between the BaTiO3 films on Si with and without the MgO layer were compared using the BaTiO3 film on MgO(100) single crystal substrate as a reference system. Also the favorable role of the MgO layer as a buffer for growing of oriented BaTiO3 films on Si substrates was confirmed.

• Journal of the Korean Ceramic Society
• /
• v.45 no.10
• /
• pp.638-643
• /
• 2008

Biomimetic apatite formation and deposition behaviors of Ti-6Al-7Nb and Ti-6Al-4V plates in simulated body fluids(SBF) under various conditions were examined. In case of regular samples without collagen treatments the weight gain due to apatite precipitation on the surface in Ti-6Al-4V was found to be higher than in Ti-6Al-7Nb. In case of collagen-coated samples, the weight gain in Ti-6Al-4V continued to be higher than in Ti-6Al-7Nb, but the difference between the two became smaller. Both Ti-6Al-7Nb and Ti-6Al-4V samples with collagen coating exhibited an appreciable increase of weight gain, which may be caused by the interaction between collagen and $Ca^{+2}$ ions. The weight gain was found to be not much affected by the addition of collagen to SBF. The ill-defined granular structure in the presence of collagen can be associated with the increasing volume fraction of amorphous calcium phosphate.

• Journal of the Korean Ceramic Society
• /
• v.47 no.6
• /
• pp.485-490
• /
• 2010

In our previous studies, continuous SiC fiber-reinforced SiC-matrix composites ($SiC_f$/SiC) had been fabricated by two different slurry infiltration methods: vacuum infiltration and electrophoretic deposition (EPD). 12 wt% of $Al_2O_3-Y_2O_3$-MgO with respect to SiC powder was used as additives for liquid-phase assisted sintering. After hot pressing at $1750^{\circ}C$ under 20 MPa for 2 h in Ar atmosphere, a high composite density could be achieved for both cases, whereas the problems such as large grain size and non-uniform distribution of liquid phase were observed, which was resulted in the relatively poor mechanical properties of composites. Therefore, efforts have been made to reduce the grain growth during the sintering, including the optimization for hot pressing condition and utilization of spark plasma sintering using a SiC monolith. Based on the results, spark plasma sintering was found to be effective method in decreasing the amount of sintering additive, time and grain growth, which will be explained in comparison to the results of hot pressing in this paper.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.209-209
• /
• 2010

Multiferroic properties of $BaTiO_3-CuFe_2O_4$ thin films grown on highly-textured Pt(111)/$TiO_2/SiO_2$/Si(100) substrates were studied. $CuFe_2O_4$ ceramic target was synthesized by mixing oxide powders of CuO, $Fe_2O_03$, $BaTiO_3$ ceramic target was also prepared separately. The film structure was of bi-layer type, where $BaTiO_3$ layer lies underneath of $CuFe_2O_4$ layer, where both layers were grown by pulsed laser deposition technique. We will report the ferroelectric and magnetic properties of $BaTiO_3-CuFe_2O_4$ bi-layer films in some detail.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.12
• /
• pp.1265-1271
• /
• 2013

In this work, modeling and analysis of thermal effects laser drilling under water for ceramics were presented. Laser is a unique tool for machining ceramics due to the characteristic of non-contact material removal. However, ablation by a laser often induces a thermal effect on the material and an increased heat-affected-zone or deposition of debris can be observed on the machined parts. The underwater surrounding improved a heat transfer rate to cooling down the machined part and could prevent any deposition of debris near the machined surfaces and edges. The heat modeling was applied to obtain the temperature distributions as well as temperature gradients between the material and surroundings. The cooling effect of the underwater laser drilling was improved and a more stable temperature distribution was calculated. The actual laser drilling results of ceramic laser drilling were presented to verify the effects of underwater laser drilling.

• Journal of the Korean Ceramic Society
• /
• v.30 no.1
• /
• pp.46-54
• /
• 1993

$\beta$-SiC was chemically vapor deposited by pyrolysis of MTS＋H2 gas mixture. The experiments were conducted in the temperature range of 1100~150$0^{\circ}C$ with a r.f. induction furnace under atmospheric pressure. The IR, XRD, EDS and AES analysis revealed that the free Si was always codeposited with SiC below 140$0^{\circ}C$, regardless of the total flow rate and MTS concentration, whereas $\beta$-SiC single phase was deposited at 150$0^{\circ}C$. C3H8 or CH2Cl2 as an excess C sources, was supplied with MTS in order to obtain stoichiometric SiC at low temperature. With the addition of C3H8 or CH2Cl2, the deposition rate was increased and $\beta$-SiC single phase could be deposited even at temperature as low as 110$0^{\circ}C$. In the absence of C3H8 or CH2Cl2, the microhardness of the layer was quite low (

• Journal of the Korean Ceramic Society
• /
• v.45 no.12
• /
• pp.807-814
• /
• 2008

The Cu-Ni-YSZ cermet anodes for direct use of methane in solid oxide fuel cells have been fabricated by electroplating Cu into the porous Ni-YSZ cermet anode. The uniform distribution of Cu in the Ni-YSZ anode could be obtained via pulse electroplating in the aqueous solution mixture of $CuSO_4{\cdot}5H_{2}O$ and ${H_2}{SO_4}$ for 30 min with 0.05 A of average applied current. The power density ($0.17\;Wcm^{-2}$) of a single cell with a Cu-Ni-YSZ anode was shown to be slightly lower in methane at $700^{\circ}C$, compared with the power density ($0.28\;Wcm^{-2}$) of a single cell with a Ni-YSZ anode. However, the performance of the Ni-YSZ anode-supported single cell was abruptly degraded over 21 h because of carbon deposition, whereas the Cu-Ni-YSZ anode-supported single cell showed the enhanced durability upto 52 h.

• Journal of the Korean Ceramic Society
• /
• v.38 no.10
• /
• pp.867-870
• /
• 2001

The carbon nanomaterials were prepared using the thermal chemical vapor deposition with ${C_2}{H_2}$ on the Ni-graphite mixture as a supported catalyst. The samples were identified by SEM, TEM, Raman spectroscopy, and the hydrogen storage measurement by electrochemical method was also carried out. The purity of carbon nanotube prepared using ground mixture was higher than that of unground one. Also, the amount of hydrogen storage of purified carbon nanomaterials was more than that of unpurified one.

• Journal of the Korean Ceramic Society
• /
• v.42 no.11 s.282
• /
• pp.763-769
• /
• 2005

Ferroelectric $ReMnO_3$(Re:Ho, Er) thin films were deposited on Si(100) substrate by Metal-Organic Chemical Vapor Deposition (MOCVD). Crystallinity and electric properties of $ReMnO_3$(Re:Ho, Er) thin films were investigated as a function of thermal heat treatment process, CHP (Conventional Heat-treatment Process) and RTP (Rapid Thermal Process). $ReMnO_3$(Re:Ho, Er) thin films prepared by RTP showed higher c-axis preferred orientation and homogeneous surface roughness than those prepared by CHP. The remnant polarization of ferroelectric hysteresis loop of $ReMnO_3$(Re:Ho, Er) thin films was strongly dependent on the c­axis preferred orientation of hexagonal single phase, and the leakage current characteristics of thin films were dependent on the homogeneity of grain size as well as surface roughness of thin films.

• Journal of the Korean Ceramic Society
• /
• v.38 no.12
• /
• pp.1110-1114
• /
• 2001

We report the mechanochemical effect of an Fe(NO$_3$)$_3$$.$9H$_2$O-Al(OH)$_3$sample as catalytic precursor mixed-ground by mixer mill on the growth of carbon nanotubes using thermal chemical vapor deposition method. From and TEM observations, carbon products grown on a ground catalyst were more uniform than those grown on an unground catalyst and most of them were identified as carbon nanobubes. Also, it was observed that field emission properties of products on ground catalyst were superior to those of unground catalyst.