• Advances in concrete construction
• /
• v.4 no.3
• /
• pp.161-172
• /
• 2016

An experimental investigation was carried out on the strength and behavior plain and fiber reinforced geopolymer concrete beam column joints and the results were compared with plain and steel fiber reinforced conventional concrete beam column joints. The volume fraction of fibers used was 0.5%. A total of six Geopolymer concrete joints and four conventional concrete joints were cast and tested under reversed cyclic loading to evaluate the performance of the joints. First crack load, ultimate load, energy absorption capacity, energy dissipation capacity stiffness degradation and moment-curvature relation were evaluated from the test results. The comparison of test results revealed that the strength and behavior of plain and fiber reinforced geopolymer concrete beam column joints are marginally better than corresponding conventional concrete beam column joints.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2000.04a
• /
• pp.30-34
• /
• 2000

In this paper we analyzed bulging condition which affect the quality of continuous casting steel by using the numerical analytic method. First solidification analyses are performed for each cooling zones. Solidification analysis are carried out by one-dimensuional finite difference method. The bulging deformation of cast slab has been calculated with a two-dimensional elasto-plastic and creep finite element model. The adequacy of the model has been checked against the experimental results. From this study the effects of the process variables such as casting speed cooling condition roll pitch are examined. The results from these analyses would be able to apply to the design of continuous casting process.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1996.04a
• /
• pp.211-215
• /
• 1996

This paper presents comparisons of pullout load of concrete with compressive strength of cylinders and cores, pulse velocity, and rebound number. A pullout test, which is a relatively new nondestructive technique, measures with a special tension ram the force required to pullout a specially shaped steel rod whose enlarged end has been cast into a concrete block. In this study 3 concrete mixes(normal strength, high-strength & super-high-strength) were made. From each mix, one 100$\times$70$\times$20 concrete block, 24 cylinders$(\phi10mm)$were casted. Each tests were performed on the concrete blocks at 3, 7, 28, and 91days. The test data shows that the pullout test is superior to the rebond hammer and the pulse velocity measurements on the evaluation of concrete strength. The pullout test is satisfactory for estimating the strength of in situ concrete at both early and late age, and its results can be reproduced with an acceptable degree of accuracy.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.03a
• /
• pp.371-378
• /
• 2001

The working load at pile is sometimes subjected to not only compression load but also lateral load and uplift forces. Pile foundation is essential and uplift load can be applied because of buoyancy, a typhoon, wind or seismic forces. This study was carried out to determine the uplift capacity of concrete pile foundation driven in clay. Pile was driven in clay, between pile and clay adhesion factor was estimated, and it is the mean value between the cast-in-situ-pile and steel pipe pile. When pile foundation is loaded for long time, creep behavior occurs. The behavior of creep is originated from the clay creep contacted with pile. The creep behavior of pile foundation embedded in clay is heavily depended on the thickness of clay around the pile shaft, pore water pressure in clay, and creep behavior of clay.

• Structural Engineering and Mechanics
• /
• v.63 no.2
• /
• pp.207-215
• /
• 2017

The paper presents the studies carried out on low velocity impact of Ultra high performance concrete (UHPC) panels of size $350{\times}350{\times}10mm^3$ and $350{\times}350{\times}15mm^3$. The panels are cast with 2 and 2.5% micro steel fibre and compared with UHPC without fiber. The panels are subjected to low velocity impact, by a drop-weight hemispherical impactor, at three different energy levels of 10, 15 and 20 J. The impact force obtained from the experiments are compared with numerically obtained results using finite element method, theoretically by energy balance approach and empirically by nonlinear multi-genetic programming. The predictions by these models are found to be in good coherence with the experimental results.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.2
• /
• pp.9-14
• /
• 1998

One of the areas in the continuous casting process that up to this point, has not been definitively instrumented is a method of reliably locating the part of a continuously cast strand that remains liquid for a period after the outer portion has solidified. To solve the problem. Electromagnetic Trandsducers(EMAT) which operate across an air gap without the need for a coupling medium has been developed. The system was designed to employ a through transmission technique which enhanced the signal-to-noise ratio. The Al 75$\times$75mm and 75$\times$100mm simulators with 2, 4, 8, 16, 32 mm hole respectively has been produced in order to verify the developed EMAT system and to measure to liquid core in continuous casting strand. The system developed can be employed for the optimization of torch cutting speed and for the final cut length of the bloom as well as calculation of average bloom temperature.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.368-371
• /
• 2008

An extensometer system to measure strain and displacement of cylindrical fatigue specimen in a autoclave of high temperature and high pressure environment has been developed by KEPRI. The extensometer reads the displacement caused by fatigue loads at the target length of the specimen installed inside the autoclave. The performance of the extensometer were tested at 15MPa, $315^{\circ}C$ of a operating pressurized water reactor. Two LVDT's of magnet type were connected to the extensometer and used for converting the fatigue displacement to electronic signal. The device is being used for developing environmental fatigue curve of CF8M cast austenitic stainless steel (CASS) in the test condition of low cycle and low strain. This paper introduces the background and results of the development.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.4
• /
• pp.104-112
• /
• 2017

In the sand casting process, the flow of liquid metal affects the quality of casting products and their die life. To determine the optimal bush part design process, this study performed various analyses using commercial finite element analysis S/W. The simulation focused on the molten metal behaviors during the mold filling and solidification stages of sand casting. This study aims to develop methods to reduce the cost and increase the tool life of the continuous hot zinc plating roll.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.2046-2052
• /
• 2008

For the lighting of vehicles structural casting components of aluminum casting alloys are substituted for those of steel or iron. For the manufacturing of large-scale premium quality aluminum castings the developments of a new casting process and a heat treatment process are necessary. The optimum casting design and heat treatment condition for large-scale castings are drawn with the help of Z-Cast software for the casting process analysis in this study. Low pressure sand casting method is applied successfully to produce air bag support components of D357 aluminum casting alloy.

• Korean Journal of Materials Research
• /
• v.7 no.7
• /
• pp.623-631
• /
• 1997

본 연구에서는 주조 2상 스테인리스강의열시효에 대한 시효온도, 시효시간 및 Nb함유량의 영향을 관찰하기 위해 기계적 성질 및 조직을 조사하였으며 Nb을 함유한 주조 2상 스테인리스강의 파괴기구를 규명하기 위해 SEM에 의한 파단면 관찰과 WDS성분분석을 통해 파괴기구의 특성을 고찰하였다. 시효온도와 시효시간이 증가함에 따라 페라니트으 미소경도가 증가하였으며 항복강도의 경우 시효온도와 시효시간에는 영향을 받지 않았으나 Nb을 함유한 재료들이 Nb을 함유치 않은 재료들에 비해 다소 낮은 항복강도 값을 보였다. 충격흡수에너지 값은 시효시간 및 시효온도의 증가에 따라 시험된 모든 재료에서 저하되었는데 0.4% Nb을 함유하는 경우 Nb을 약간 함유하거나 함유치 않은 재료들에 비해 시효시간에 따라 급격한 감소 경향을 보였다. 파단면 관찰결과 페라이트 기지 또는 페라이트/오스테나이트 상경계에서 석출된 VbC를 비롯한 탄화물들이 취성저항성을 낮추는데 크게 기여했음을 알 수 있었다.