• Analytical Science and Technology
• /
• v.18 no.5
• /
• pp.403-409
• /
• 2005

Polycyclic Aromatic Hydrocarbons(PAHs) contamination arises from several sources including processing of food(smoking, direct drying, cooking) and environmental contamination of air, water, or soil, the later being considered as the most important. In this study, to establish the analytical method for some PAHs[benzo(a)anthracene, chrysene, benzo(b)fluoranthene, benzo(k)fluoranthene, benzo(a)pyrene, dibenzo(a,h)anthracene, benzo(g,h,i)perylene, indeno(1,2,3-c,d)pyrene] in fish, alkali digestion time, extraction solvents, elution volume of florisil cartridge for clean-up have been optimized. The methodology involved saponification and extraction with n-hexane, clean-up on Sep-Pak florisil cartridges and determination by HPLC/FLD(High Performance Liquid Chromatography/Fluorescence Detector). Overall method recoveries for 8 PAHs spiked into these products ranged from 90 to 106%.

• Explosives and Blasting
• /
• v.30 no.2
• /
• pp.52-58
• /
• 2012

A TBM launching shaft in DTL2 Contract 915 site is located in a typical hard Bukit Timah granite formation and lots of blasting work is required for shaft sinking. The original blast design used the electric detonator and ANFO blasts consisting of 30 holes per one blast with 1.5 m depth of drilling hole. However, significant delay of work and poor progress were expected due to the limitation of the number of blasting hole and strict vibration regulation on retaining systems. To overcome such constraints, an efficient new blasting method which can improve productivity and satisfy vibration limit was required. The revised blast design, using triple-deck blasts with electronic detonators and cartridge emulsion explosives, gives better construction performance and can reduce construction time. Such a new blasting technique can be effectively used for similar underground projects in the future where the volume of rock blasting is significant.

• Steel and Composite Structures
• /
• v.36 no.4
• /
• pp.369-381
• /
• 2020

Nowadays, in prefabricated composite construction, composite action between steel beam and concrete slab is often achieved with positioning of shear connectors in envisaged openings of concrete slabs. Prefabricated concrete slabs are used for composite steel-concrete buildings and bridges, both for the construction of new structures and for renovation of existing ones, significantly reducing construction time. Development of different types of shear connectors represent alternative solution to the traditionally used headed studs, considering their shear resistance, stiffness and ductility. New types of shear connectors tend to reduce the construction time and overall construction cost. Mechanically fastened shear connectors represent a viable alternative to headed studs, considering their fast installation process and shear resistance. X-HVB shear connectors are attached to the steel beam with two cartridge fired pins. The first step towards extensive implementation of X-HVB shear connectors in composite construction is to understand their behaviour through experimental investigation. Results of the push-out tests, in accordance to Eurocode 4, with X-HVB 110 shear connectors positioned in envisaged openings of prefabricated concrete slabs are presented in this paper. The experimental investigation comprised three different specimen's layout. Group arrangement of X-HVB shear connectors in envisaged openings included specimens with minimal recommended distances and specimens with reduced distances between connectors in both directions. Influence of different installation procedures on overall behaviour of the connection is presented, as well as the orientation of shear connectors relative to the shear force direction. Influence of variations is characterized in terms of failure mechanisms, shear resistance and ductility.

• Journal of Dental Anesthesia and Pain Medicine
• /
• v.17 no.2
• /
• pp.121-127
• /
• 2017

Background: There are no studies regarding 4% articaine infiltration injection into the retro-molar area for an impacted lower third molar (LITM) surgery. This study aimed to evaluate the efficacy of infiltration using 1.7 ml (single cartridge: SC) of 4% articaine versus 3.4 ml (double cartridges: DC) of 4% articaine with 1:100,000 epinephrine in LITM surgery. Method: This study involved 30 healthy patients with symmetrical LITM. The patients were assigned to receive either a DC or SC of 4% articaine with 1:100,000 epinephrine as a local anesthetic for each operation. Onset, duration, profoundness, need for additional anesthetic administration, total volume of anesthetic used, vitality of the tooth, and pain score during operation were recorded. Results: The DC of 4 % articaine had a significantly higher success rate (83.3%) than did the SC (53.3%; P<0.05). The duration of soft tissue anesthesia was longer in the DC group. The intra-operative pain was higher in the SC group with a significant (P < 0.05) requirement for a supplementary local anesthetic. Conclusion: We concluded that using DC for the infiltration injection had a higher success rate, longer duration of anesthesia, less intra-operative pain, and a lower amount of additional anesthesia than SC in the surgical removal of LITM. We recommend that a DC of 4% articaine and a 1:100,000 epinephrine infiltration in the retro-molar region can be an alternative anesthetic for LITM surgery.

• Journal of computational fluids engineering
• /
• v.21 no.2
• /
• pp.90-98
• /
• 2016

A numerical study is conducted on thermal performance of a large-area hot plate specially designed as a heating and cooling tool for thermal nanoimprint lithography process. The hot plate has a dimension of $240mm{\times}240mm{\times}20mm$, in which a series of cartridge heaters and cooling holes are installed. The material is stainless steel selected for enduring the high molding pressure. A numerical model based on the ANSYS Fluent is employed to predict the thermal behavior of the hot plate both in heating and cooling phases. The PID thermal control of the device is modeled by adding user defined functions. The results of numerical computation demonstrate that the use of cartridge heaters provides sufficient heat-up performance and the active liquid cooling in the cooling holes provides the required cool-down performance. However, a crucial technical issue is raised that the proposed design poses a large temperature non-uniformity in the steady heating phase and in the transient cooling phase. As a remedy, a new hot plate in which heat pipes are installed in the cooling holes is considered. The numerical results show that the installation of heat pipes could enhance the temperature uniformity both in the heating and cooling phases.

• Journal of Microbiology and Biotechnology
• /
• v.25 no.3
• /
• pp.328-333
• /
• 2015

A Myagropsis myagroides (Mm) methanol extract showed α-amylase inhibitory activity of 13% at a concentration of 5 mg/ml. Results showed that the hexane fraction from the Mm methanol extract exhibited α-amylase inhibitory activity with an IC₅₀ value of 4.24 mg/ml. The hexane fraction was separated using silica-gel column chromatography, and six subfractions were obtained. The fraction eluted with CHCl₃:MeOH = 50:1 showed the highest α-amylase inhibitory activity with an IC₅₀ value of 0.72 mg/ml. This fraction was purified using Sephadex LH-20 column chromatography and an octadecyl silica (ODS) Sepak cartridge, obtaining seven subfractions. Fraction (Fr.) 4 also showed a strong α-amylase inhibitory activity with an IC₅₀ value of 0.75 mg/ml. Fr. 4 was purified by Sephadex LH-20 column chromatography and ODS Sepak cartridge, obtaining six subfractions. Fr. 4-2 was identified as sargachromanol I with an IC₅₀ value of 0.40 mg/ml, and the inhibition pattern analyzed from Lineweaver-Burk plots revealed it to be an uncompetitive inhibitor. These results suggest that Mm has potential as a natural antidiabetes agent.

• Journal of Life Science
• /
• v.20 no.10
• /
• pp.1511-1518
• /
• 2010

The antimicrobial activity of 70% ethanol extracts from Rosa multiflora Thunberg fruit against Helicobacter pylori was examined. The inhibitory activity of Rosa multiflora Thunberg fruit extracts against H. pylori was determined to clear a zone of 14 mm with 70% ethanol extracts. Purification of inhibitory compounds was carried on Sephadex LH-20 and $C_{18}$ cartridge column chromatography using a gradient procedure, with increasing ethanol ($0{\rightarrow}100%$) in $H_2O$. The chemical structure of the purified inhibitory compounds on H. pylori was identified to be protocatechuic acid, chlorogenic acid and quercetin by FAB-MS, NMR and IR spectrum.

• Journal of Environmental Health Sciences
• /
• v.37 no.1
• /
• pp.50-56
• /
• 2011

The adsorption capacity of charcoal is a function of the airborne concentration of the target chemical. To evaluate the adsorption capacity of charcoal packed in the cartridges of air purifying respirators, breakthrough tests were conducted with carbon tetrachloride for three commercial cartridges (3M models #7251, #6000 and AX) at 25, 50, 100, 250 and 500 ppm. Adsorption capacities were calculated using a mass transfer balance equation derived from the curve fitting to the breakthrough curves obtained experimentally. Carbon micropore volumes were estimated by iteration to fit the Dubinin/Radushkevich (D/R) adsorption isotherm. They were 0.6566, 0.5727 and 0.3087 g/cc for #7251, #6000 and the AX cartridge, respectively. Above 100 ppm (at high challenge concentrations), #7251 and #6000 showed higher adsorption capacities. However, as the challenge concentration decreased, the adsorption capacities of #7251 and #6000 sharply dropped. On the other hand, the adsorption capacity of the AX cartridge showed little change with the decrease of the challenge concentration. Thus, the AX showed a higher adsorption capacity than #7251 and #6000 at the 5-50 ppm level. It is concluded that service-life tests of cartridges and adsorption capacity tests of charcoal should be conducted at challenge concentration levels reflecting actual working environmental conditions. Alternatively, it is recommended to use the D/R adsorption isotherm to extrapolate adsorption capacity at low concentration levels from the high concentration levels at which breakthrough tests are conducted, at a minimum of two different concentration levels.

• Journal of the Korean Chemical Society
• /
• v.35 no.6
• /
• pp.720-724
• /
• 1991

Simultaneous determination of chloragenic acid (CA), 3,4-o-dicafeoyl quinic acid(3,4-DCQA), 4,5-o-dicaffeoyl quinic acid (4,5-DCQA) and linarin in Chrysanthemum sibiricum Fisher was newly established by a reversed-phase high performance liquid chromatography (HPLC). Sample was extracted with 20 ml methanol for 4 hrs. The extract was cleaned up by using Sep-Pak $C_18$ cartridge and 4 ml methanol-$H_2$O(1 : 1) as eluent. Their determination was performed by means of RP-HPLC with Bondapak $C_18$ column (30 cm ${\times}$ 3.9 mm i.d., 10 ${\mu}m$ and gradient elution mode as methanol-5 mM $H_3PO_4$ solution (30 : 70). The established method was applied to various samples purchased. As a result, their content ranges showed to be 0.35~0.55% for CA, 0.46~0.76% for 3,5-DCQA, 0.077~0.23% for 4,5-DCQA and 0.16~2.72% for linarin, respectively.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.3
• /
• pp.131-137
• /
• 2017

In order to safely protect high over current flowing into the main circuit at short-circuit without any explosion or fire, the enclosed cartridge fuse with a high interrupting capacity should be applied. But this fuse is impossible to be applied to an inner electronic circuit because of a limited space problem result from the miniaturization trend of products. Therefore, it is necessary to apply a sub-miniature fuse with a relatively small size. However the semi-enclosed fuse which is more free for an influx of air than the enclosed cartridge fuse and is possible to protect fuse elements with chemical and physical combination can be adoptable. But it has a limit of implementing the characteristic of a high breaking capacity. For these reasons, the Fe-42wt％Ni fuse elements alloy and fuse-link with less space were designed to increase a breaking capacity of sub-miniature fuse and its safety for fire and explosion was confirmed in this paper.