• 전기의세계
• /
• 제15권5호
• /
• pp.25-31
• /
• 1966

This paper derives the useful formulas for computing annual profits, and economical size, locations and regulating values of parallel shunt capacitors in case that they are installed in a distribution line. Inparticular, the derived formulas consider the influence of load variations in order to represent the actual load situations.

• 대한전자공학회논문지SD
• /
• 제41권5호
• /
• pp.99-105
• /
• 2004

더미 비트라인을 이용한 공유 커패시터 전하공유 롬(shared-capacitor charge-sharing ROM SCCS-ROM)이 제안되었다. SCCS-ROM은 기존의 전하공유 롬(charge-sharing ROM, CS-ROM)의 전하공유 기법으로 비트라인의 스윙전압을 줄였다. CS-ROM에서는 출력 비트 마다 3개의 작은 커패시턴스들이 필요하지만, 제안된 SCCS-ROM은 그 커패시터들을 공유함으로써 필요한 커패시터의 수를 단지 3개로 줄였다. 또한, 더미 비트라인들(dummy bit lines)로 커패시터들을 구현함으로써, 잡음내성을 증가시켰을 뿐만 아니라 소모전력 또한 줄였다. 8K×15bi1s의 SCCS-ROM이 0.35㎛ CMOS 공정으로 구현되었다. SCCS-ROM은 3.3V의 100㎒ 동작에서 8.63㎽의 전력을 소모하였다. 시뮬레이션에서 SCCS-ROM은 CS-ROM보다 8.4% 적은 전력을 소모하였다.

• 전기학회논문지P
• /
• 제66권4호
• /
• pp.236-241
• /
• 2017

This paper presents a single-phase grid connected voltage-ed inverter with a power decoupling circuit. In the single-phase grid connected voltage-ed inverter, it is well known that a power pulsation with twice the grid frequency is contained in the input power. In a conventional voltage type inverter, electrolytic capacitors with large capacitance have been used in order to smooth the DC voltage. However, lifetime of those capacitors is shortened by the power pulsation with twice grid frequency. The authors have been studied a active power decoupling(APD) method that reduce the pulsating power on the input DC bus line, this enables to transfer the ripple energy appeared on the input DC capacitors into the energy in a small film capacitor on the additional circuit. Hence, extension of the lifetime of the inverter can be expected because the small film capacitor substitutes for the large electrolytic capacitors. Finally, simulation and experimental results are discussed.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제52권12호
• /
• pp.624-631
• /
• 2003

This paper presents a simple carrier symmetric method for the voltage balance of flying capacitors in FCMLI(flying capacitor multi-level inverter). To achieve the voltage balance of flying capacitors, the utilization of each carrier must be balanced during a half-cycle of the switching period such as PSPWM(Phase-Shifted PWM). However, the CRPWM(Carrier Redistribution PWM) method causes the fluctuation of flying capacitor voltages because the balanced utilization of carriers is not achieved. Moreover, it does not consider that the load current change has an influence on flying capacitor voltages by assuming that the current flows into the load. To overcome the drawbacks of CRPWM, it is modified by the technique that carriers of each band are disposed symmetrically at every fundamental period. Firstly, the CRPWM method is reviewed and the theory on voltage balance of flying capacitors is analyzed. The proposed method is introduced and is verified through the experiment result.

• 한국전기전자재료학회논문지
• /
• 제17권12호
• /
• pp.1283-1288
• /
• 2004

Metal-ferroelectric-insulator-semiconductor(WFIS) capacitors using rapid thermal annealed LiNbO$_3$/AlN/Si(100) structure were fabricated and demonstrated nonvolatile memory operations. The capacitors on highly doped Si wafer showed hysteresis behavior like a butterfly shape due to the ferroelectric nature of the LiNbO$_3$ films. The typical dielectric constant value of LiNbO$_3$ film in the MFIS device was about 27, The gate leakage current density of the MFIS capacitor was 10$^{-9}$ A/cm$^2$ order at the electric field of 500 kV/cm. The typical measured remnant polarization(2P$_{r}$) and coercive filed(Ec) values were about 1.2 $\mu$C/cm$^2$ and 120 kV/cm, respectively The ferroelectric capacitors showed no polarization degradation up to 10$^{11}$ switching cycles when subjected to symmetric bipolar voltage pulses of 1 MHz. The switching charges degraded only by 10 % of their initial values after 4 days at room temperature.e.

• 전자공학회논문지A
• /
• 제33A권2호
• /
• pp.114-121
• /
• 1996

Thin film Ba$^{0.7}Sr^{0.3}TiO^{3}$ (BST) capacitors were fabricated on SiO$_{2}$/Si substrates by RF magnetron sputtering method and characterized at microwave frequencies ranging from 40 MHz to 1GHz to examine the dielectric dispersion of the capacitors. The BST thin films were electrode material of BST thin films capacitor which is known as one of the best electrode materials for BST films. 50$\AA$-thick titanium (Ti) layers were introduced to increase adhesion between bottom Pt and SiO$_{2}$. The leakage current density of the capacitors was about 1.7${\times}10^{7}A/cm^{2}$ at 1.5V and the dielectric constant was about 140 at 1MHz. Microwave measurement patterns having a coplanar waveguide type were fabricated and their S parameters were measured using network analyzer. After de-embedding parasitic components in microwave measurement patterns nearly frequency-invariant dielectric constant of about 120 was extracted in the measurement range of 40 MHz to 1 GHz.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 춘계학술대회 논문집
• /
• pp.1694-1700
• /
• 2007

In the electrified section, both of return current and signal current are flowing in the same rail in common. But signal current shall be allowed to flow in the specific track circuit and not in the other circuit while the traction return current shall come back to power sub-station. This paper presents measuring system that use both sensor and antenna. The aim of the system is to achieve the difference in current between the two rails and the presence of trimming capacitors. In order to improve the transmission level, trimming capacitors are connected between the two rails at constant spacing. To maintain the balance of traction return current, rails of both sides may be jointed by the so-called SVPMM. The traction return current is sometimes unbalanced owing to the ill-contact of SVPMM. In this paper, we propose a diagnosis method based on a short-circuited current(Icc), trimming capacitors and traction return current measured by Korail inspection vehicles. Whether Icc is good or bad depends not only on the presence of trimming capacitors but also on the unbalance of the traction return current.

• 한국안전학회지
• /
• 제26권6호
• /
• pp.13-19
• /
• 2011

The purpose of this study is to examine the cause of damage to electrolytic capacitors and to present the heat generation mechanism in order to prevent the occurrence of similar problems. From the analysis results of electrolytic capacitors collected from accident sites, the fire causing area can be limited to the primary power supply for the initial accident. From the tests performed by applying overvoltage, surge, etc., it is thought that the fuse, varistor, etc., are not directly related to the accidents that occurred. The analysis of the characteristics using a switching regulator showed that the charge and discharge characteristics fell short of standard values. In addition, it is thought that heated electrolytic capacitors caused thermal stress to nearby resistances, elements, etc. It can be seen that the heat generation is governed by the over-ripple current, application of AC overvoltage, surge input, internal temperature increase, defective airtightness, etc. Therefore, when designing an electrolytic capacitor, it is necessary to comprehensively consider the correct polarity arrangement, appropriate voltage application, correct connection of equivalent series resistance(ESR) and equivalent series inductance(SEL), rapid charge and discharge control, sufficient margin of dielectric tangent, etc.

• 전기학회논문지P
• /
• 제61권4호
• /
• pp.186-191
• /
• 2012

DC Bus Electrolytic capacitors have been widely used in power conversion system because they can achieve high capacitance and voltage ratings with volumetric efficiency and low cost. This type of capacitors have been traditionally used for filtering, voltage smoothing, by-pass and other many applications in power conversion circuits requiring a cost effective and volumetric efficiency components. Unfortunately, electrolytic capacitors are some of the weakest components in power electronic converter. Many papers have proposed different methods or algorithms to determinate the ESR and/or capacitance C for fault diagnosis of the electrolytic capacitor. However, both ESR and C vary with frequency and temperature. Accurate knowledge of both values at the capacitors operating conditions is essential to achieve the best reference data of fault judgement. According to parameter analysis, the capacitance increases with temperature and the ESR decreases. Higher frequencies make the ESR and C to decrease. Analysis results show that the proposed electrolytic capacitor parameter estimation technique can be applied to reference signal of capacitor diagnosis systems successfully.

• 한국전기전자재료학회논문지
• /
• 제16권3호
• /
• pp.207-213
• /
• 2003

The Sr$\_$0.7/Bi$\_$2.6/Ta$_2$O$\_$9/(SBT) thin films are deposited on Pt-coated electrode(Pt/TiO$_2$/SiO$_2$/Si) using RF magnetron sputtering method. The structural and electrical properties of SBT capacitors were influenced with annealing atmosphere. In the XRD pattern, the SBT thin films in all annealed atmosphere had (105) orientation. In the SEM images, Bi-layered perovskite phase was crystallized in all annealing atmosphere and grain largely grew in oxygen annealing atmosphere. The maximum remnant polarization and the coercive electric field in oxygen annealing atmosphere are 12.40[${\mu}$C/cm$^2$] and 30[kV/cm] respectively. The dielectric constant and leakage current density of capacitors annealed oxygen atmosphere are 340 and 2.13${\times}$10$\^$-9/ [A/cm$^2$] respectively. The fatigue characteristics of SBT capacitors did not change up to 10$\^$10/ switching cycles.