• Journal of the Korean Vacuum Society
• /
• v.20 no.6
• /
• pp.395-402
• /
• 2011

The nanomechanical properties of fully lithiated and unlithiated silicon nanowire deposited on silicon substrate have been studied with atomic force microscopy. Silicon nanowires were synthesized using the vapor-liquid-solid process on stainless steel substrates using Au catalyst. Fully lithiated silicon nanowires were obtained by using the electrochemical method, followed by drop-casting on the silicon substrate. The roughness, derived from a line profile of the surface measured in contact mode atomic force microscopy, has a smaller value ($0.65{\pm}0.05$ nm) for lithiated silicon nanowire and a higher value ($1.72{\pm}0.16$ nm) for unlithiated silicon nanowire. Force spectroscopy was utilitzed to study the influence of lithiation on the tip-surface adhesion force. Lithiated silicon nanowire revealed a smaller value (~15 nN) than that of the Si nanowire substrate (~60 nN) by a factor of two, while the adhesion force of the silicon nanowire is similar to that of the silicon substrate. The elastic local spring constants obtained from the force-distance curve, also shows that the unlithiated silicon nanowire has a relatively smaller value (16.98 N/m) than lithiated silicon nanowire (66.30 N/m) due to the elastically soft amorphous structures. The frictional forces of lithiated and unlithiated silicon nanowire were obtained within the range of 0.5-4.0 Hz and 0.01-200 nN for velocity and load dependency, respectively. We explain the trend of adhesion and modulus in light of the materials properties of silicon and lithiated silicon. The results suggest a useful method for chemical identification of the lithiated region during the charging and discharging process.

• Journal of Korea Water Resources Association
• /
• v.39 no.4 s.165
• /
• pp.299-311
• /
• 2006

In this paper it is outlined the methodology of estimating the parameters of water balance analysis method for calculating recharge, using ground water level rises in monitoring well when values of specific yield of aquifer are not available. This methodology is applied for two monitoring wells of the case study area in northern area of the Jeiu Island. A water balance of soil layer of plant rooting zone is computed on a daily basis in the following manner. Diect runoff is estimated by using SCS method. Potential evapotranspiration calculated with Penman-Monteith equation is multiplied by crop coefficients($K_c$) and water stress coefficient to compute actual evapotranspiration(AET). Daily runoff and AET is subtracted from the rainfall plus the soil water storage of the previous day. Soil water remaining above soil water retention capacity(SWRC) is assumed to be recharge. Parameters such as the SCS curve number, SWRC and Kc are estimated from a linear relationship between water level rise and recharge for rainfall events. The upper threshold value of specific yield($n_m$) at the monitoring well location is derived from the relationship between rainfall and the resulting water level rise. The specific yield($n_c$) and the coefficient of determination ($R^2$) are calculated from a linear relationship between observed water level rise and calculated recharge for the different simulations. A set of parameter values with maximum value of $R^2$ is selected among parameter values with calculated specific yield($n_c$) less than the upper threshold value of specific yield($n_m$). Results applied for two monitoring wells show that the 81% of variance of the observed water level rises are explained by calculated recharge with the estimated parameters. It is shown that the data of groundwater level is useful in estimating the parameter of water balance analysis method for calculating recharge.

• Korean Journal of Weed Science
• /
• v.18 no.2
• /
• pp.128-135
• /
• 1998

The experiment was carried out to obtain basic informations on sod culture using water foxtail in apple orchard at Kyeongbuk Provincial RDA in 1996 to 1997. Period of seedling emergence varied with sowing time and accumulative temperature. Sowing at Nov. 25 required longer than 100 days, while it needed only 8 days when water foxtail was sowed at Sep. 20. In a view of accumulative temperature, sowing at March 15 needed $139^{\circ}C$ but it required about $1,000^{\circ}C$ at August 10. This result showed that the seed of water foxtail has strong summer-dormancy in natural condition. Water foxtail had s-shape growth curve during growing season, and growth rate was the highest from March to May in this period. Plant height increased 2 times and 4 times for dry weight from March 20 to April 20. However, growth was decreased by summer depression after May. Major weeds in apple orchard were horseweed, akino-nogeshi and shepherd's-purse. These species were suppressed by the dominance of water foxtail. Water foxtail as a cover plant could be used for a method of weed control instead of herbicide in apple orchard.

• Radiation Oncology Journal
• /
• v.20 no.3
• /
• pp.283-293
• /
• 2002

Purpose : A PC based brachytherapy planning system was developed to display dose distributions on simulation images by 2D isodose curve including the dose profiles, dose-volume histogram and 30 dose distributions. Materials and Methods : Brachytherapy dose planning software was developed especially for the Ir-192 source, which had been developed by KAERI as a substitute for the Co-60 source. The dose computation was achieved by searching for a pre-computed dose matrix which was tabulated as a function of radial and axial distance from a source. In the computation process, the effects of the tissue scattering correction factor and anisotropic dose distributions were included. The computed dose distributions were displayed in 2D film image including the profile dose, 3D isodose curves with wire frame forms and dosevolume histogram. Results : The brachytherapy dose plan was initiated by obtaining source positions on the principal plane of the source axis. The dose distributions in tissue were computed on a $200\times200\;(mm^2)$ plane on which the source axis was located at the center of the plane. The point doses along the longitudinal axis of the source were $4.5\~9.0\%$ smaller than those on the radial axis of the plane, due to the anisotropy created by the cylindrical shape of the source. When compared to manual calculation, the point doses showed $1\~5\%$ discrepancies from the benchmarking plan. The 2D dose distributions of different planes were matched to the same administered isodose level in order to analyze the shape of the optimized dose level. The accumulated dose-volume histogram, displayed as a function of the percentage volume of administered minimum dose level, was used to guide the volume analysis. Conclusion : This study evaluated the developed computerized dose planning system of brachytherapy. The dose distribution was displayed on the coronal, sagittal and axial planes with the dose histogram. The accumulated DVH and 3D dose distributions provided by the developed system may be useful tools for dose analysis in comparison with orthogonal dose planning.

• Journal of the Korean Society of Radiology
• /
• v.8 no.4
• /
• pp.181-187
• /
• 2014

The purpose of this study were to analyze the characteristic of the glow curves in order to the glow temperature of the thermoluminescent dosimeters (TLDs) for the absorbed dose measurement of the radiation therapy. In this study, we was used the TLDs of the LiF:Mg${\cdot}$Ti, LiF:Mg${\cdot}$Cu${\cdot}$P, $CaF_2$:Dy, $CaF_2$:Mn (Thermo Fisher Scientific Inc., USA). The source-to-solid dry phantom (RW3 slab, IBA Dosmetry, Germany) surface distance was set at 100 cm, and the exposure dose of 100 MU (monitor unit) was used 6- and 15-MV X-rays, and 6- and 12-MeV electron beams in the reference depth, respectively. After the radiations exposure, we were to analyze the glow curves by using the TL reader (Hashaw 3500, Thermo Fisher Scientific Inc., USA) at the fixed heating rate of $15^{\circ}C/sec$ from $50^{\circ}C$ to $260^{\circ}C$. The glow peaks, the trapping level in the captured electrons and holes combined with the emitted light, were discovered the two or three peak. When the definite increasing the temperature of the TLDs, the maximum glow peak representing the glow temperature was follow as; $LiF:Mg{\cdot}Ti$: $185.5{\pm}1.3^{\circ}C$, $LiF:Mg{\cdot}Ti$: $135.0{\pm}5.1^{\circ}C$, $CaF_2$:Dy: $144.0{\pm}1.6^{\circ}C$, $CaF_2$:Mn: $294.3{\pm}3.8^{\circ}C$, respectively. Because the glow emission probability of the captured electrons depend on the heating temperature after the exposure radiation, TLDs by applying the fixed heating rate, the accuracy of measurement will be able to improve within the absorbed dose measurement of the radiation therapy.

• Pediatric Infection and Vaccine
• /
• v.16 no.1
• /
• pp.40-46
• /
• 2009

Purpose : The purpose of this study was to identify useful predictors for diagnosing bacterial meningitis and performing CSF studies in febrile infants three months or younger. Methods : Six hundred and fifty two febrile infants with a rectal temperature ${\geq}38.0^{\circ}C$ presented from January 2003 to April 2008 and were retrospectively studied. The total white blood cell count (WBC), band count, absolute neutrophil count (ANC), quantitative C-reactive protein (CRP) and blood cultures were performed on admission. The clinical variables associated with bacterial meningitis were analyzed. Results : In patients with bacterial meningitis, the clinical variables including CRP (P=0.036), band count (P=0.037), ANC (P=0.036) and age (P=0.001) were significantly different. The area under the receiver-operating characteristic curve was 0.969 for CRP, 0.946 for the band count, 0.765 for the ANC and 0.235 for age. A CRP cutoff point of 8 mg/dL was determined to maximize both the sensitivity and specificity (sensitivity 83%, specificity 95%, likelihood ratio 16.6). A CRP concentration of <7 mg/dL "ruled-out" bacterial meningitis, with a likelihood ratio of 0.17, a posttest probability of <0.1% and negative predictive value 91%. A CRP concentration greater than 9 mg/dL had a much higher likelihood ratio (20.1) than the band count (16.6) and ANC (2.2). Conclusion : The CRP concentration was a useful laboratory test for the differential diagnosis of bacterial meningitis among febrile infants three months of age or younger. A CRP concentration of <7 mg/dL effectively ruled out bacterial meningitis; a value ${\geq}9mg/dL$ increased the clinical suspicion of bacterial meningitis and the need for CSF evaluation.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.22 no.1
• /
• pp.31-44
• /
• 2017

Pfiesteria piscicida is one of heterotrophic dinoflagellate having toxic metaboliges, and it is difficult to detect and quantify this dinoflagellate via light microscope due to small size and morphological similarity with Pfiesteria-like dinoflagellate (PLD) species. Alternatively, we developed quantitative real-time PCR assay based on EvaGreen and determined field accessibility throughout the investigation of distribution in the entire Korean coastal waters and population dynamics in Shihwa Lake. The P. piscicida-specific primers based on internal transcribed spacer 1 (ITS 1) were designed and the specificity of primers was confirmed by PCR with other genomic DNAs which have genetic similarity with target species. Through real-time PCR assay, a standard curve which had a significant linear correlation between log cell number and $C_T$ value ($r^2{\geq}0.999$) and one informative melting peak ($88^{\circ}C$) were obtained. These results implies that developed real-time PCR can accurately detect and quantify P. piscicida. Throughout the field applications of real-time PCR assay, P. piscicida was distributed in western (Mokpo and Kimje) and easthern (Gangneng) Korean coastal water even though light microscopy failed to identify P. piscicida. In the investigation of population dynamics in Shihwa Lake, the density of P. piscicida was peaked in June, July and August 2007 at St. 1 where salinity (${\leq}15psu$) was lower than the other 2 sites. In this study, we successed to develop EvaGreen bassed real-time PCR for detection and quantification of P. piscicida in fields, so this developed assay will be useful for various ecological studies in the future.

• Horticultural Science & Technology
• /
• v.31 no.1
• /
• pp.80-88
• /
• 2013

Carrot (Daucus carota L. var. sativa) is one of the most extensively used vegetable crops in the world and a significant source of nutrient because of its high content of ${\beta}$-carotene, well known as the precursor of vitamin A carotenoid. However, seed-hairs generated and elongated from the epidermal cell of seeds inhibit absorption and germination by various factors such as carotol and so on. Accordingly, mechanical hair removal process is essential before commercialization of carrot seeds. Because of this process, producers will have additional losses such as time consuming, manpower, capital and so on. Furthermore, physical damage of seeds causes irregular germination rate. To overcome such cumbersome weaknesses, new breeding program for developing hairless-seed carrot cultivar has been needed and studies for molecular markers related to seed-hair characteristic is needed for a new breeding program. Therefore, in this study, cDNA libraries from seeds of short-hair seed phenotype CT-SMR 616 OP 659-1 line, hairy-seed phenotype CT-SMR 616 OP 677-14 line and short-hair seed phenotype CT-ATR 615 OP 666-13 line, hairy-seed phenotype CT-ATR 615 OP 671-9 were constructed, respectively. Furthermore, 1,248 ESTs in each line, total 4,992 ESTs were sequenced. As a result, 19 SNP sites and 14 SNP sites in each of 2 combinations were confirmed by analyzing these EST sequences from short-hair and hairy-seed lines. Then we designed SNP primer sets from EST sequences of SNP sites for high resolution melting (HRM) analysis. Designed HRM primers were analyzed using hairy seed phenotype CT-SMR 616 OP 1040 line and short-hair seed phenotype CT-SMR 616 OP 1024, 1025, 1026 lines. One set of HRM primers showed specific difference between the melting curves of hairy and short-hair seed phenotype lines. Based on this result, allele-specific (AS) PCR primers were designed for easier selection between hairy-seed carrot and hairless seed carrot. These results of HRM and AS-PCR are expected to be useful in breeding of hairless seed carrot cultivar as a molecular marker.

• Korean Journal of Food Science and Technology
• /
• v.40 no.2
• /
• pp.152-159
• /
• 2008

The purpose of this study was to determine the accurate quantification of vitamin A in infant formula by comparing two different standard stock solutions as well as various sample weights using high performance liquid chromatography. The sources of uncertainty in measurement, such as sample weight, final smaple vloume, and the instrumental results, were identified and used as parameters to determine the combined standard uncertainty based on GUM(guide to the expression of uncertainty in measurement) and the Draft EURACHEM/CITAC Guide. The uncertainty components in measuring were identified as standard weight, purity, molecular weight, dilution of the standard solution, calibration curve, recovery, reproducibility, sample weight, and final sample volume. Each uncertainty component was evaluated for type A and type B and included to calculate the combined uncertainty. The analytical results and combined standard uncertainties of vitamin A according to the two different methods of stock solution preparation were 627 ${\pm}$ 33 ${\mu}$g R.E./100 g for 1,000 mg/L of stock solution, and 627 ${\pm}$ 49 ${\mu}$g R.E./100 g for 100 mg/L of stock solution. The analytical results and combined standard uncertainties of vitamin A according to the various sample weighs were 622 ${\pm}$ 48 ${\mu}$g R.E./100 g, 627 ${\pm}$ 33 ${\mu}$g R.E./100 g, and 491 ${\pm}$ 23 ${\mu}$g R.E./100 g for 1 g, 2 g, and 5 g of sampling, respectively. These data indicate that the preparation method of standard stock solution and the smaple amount were main sources of uncertainty in the analysis results for vitamin A. Preparing 1,000 mg/L of stock solution for standard material sampling rather than 100 mg, and sampling not more than 2 g of infant formula, would be effective for reducing differences in the results as well as uncertainty.

• Korean Journal of Food Science and Technology
• /
• v.48 no.5
• /
• pp.399-404
• /
• 2016

The applicability of photostimulated-luminescence (PSL) and thermoluminescence (TL) for the detection of 12 food materials (potato, onion, garlic, dried pumpkin, black mushroom, black soybean, Cheongkukjang powder, sea mustard, pepper powder, Ramyun soup, corn tea, and green tea powder) irradiated with an electron beam, gamma ray, and X ray at a range of 0.15 to 10 kGy was investigated. For PSL, negative results (less than 700 photon counts (PCs)) were observed from non-irradiated foods while the irradiated foods showed intermediate (879 to 2,414 PCs) and/or positive (19,951 to 65,919,035 PCs) values. In all irradiated samples, the maximum peak of the TL glow curve was observed between 150 and $250^{\circ}C$. Our findings demonstrate the successful application of PSL and TL to determine whether food items were irradiated or not. However, there were no significant differences among the radiation sources.