• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.11
• /
• pp.107-113
• /
• 2014

A VCO (Voltage Controlled Oscillator) and a divide-by-4 high speed frequency divider are implemented using 65nm CMOS technology for 60GHz wireless communication system. The mm-wave VCO was designed by NMOS cross-coupled LC type using current source. The architecture of the divide-by-4 high speed frequency divider is differential ILFD (Injection Locking Frequency Divider) with varactor to control frequency range. The frequency divider also uses current sources to get good phase noise characteristics. The measured results show that the VCO has 64.36~67.68GHz tuning range and the frequency divider divides the VCO output by 4 exactly. The high output power of 5.47~5.97dBm from the frequency divider is measured. The phase noise of the VCO including the frequency divider are -77.17dBc/Hz at 1MHz and -110.83dBc/Hz at 10MHz offset frequency. The power consumption including VCO is 38.4mW with 1.2V supply voltage.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.5C
• /
• pp.395-402
• /
• 2008

In this paper, an I/Q channel 12bits 40MS/s Pipeline Analog to Digital Converter that is able to apply to WLAN/WMAN system is proposed. The proposed ADC integrates DLL based duty-correction circuit which corrects the fluctuations in the duksty cycle caused by miniaturization of CMOS devices and faster operating speeds. It is designed as a 1% to 99% input clock duty cycle could be corrected to 50% output duty cycle. The prototype ADC is implemented in a $0.18{\mu}m$ CMOS n-well 1-poly 6-metal process and dissipates 184mW at 1.8V single supply The SNDR of the proposed 12bit ADC is 52dB and SFDR of 59dBc(@Fs=20MHz, Fin=1MHz) is measured.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.5 s.120
• /
• pp.530-538
• /
• 2007

An inductor library for efficient low cost RFIC design has been developed based on a standard digital 0.18 ${\mu}m$ CMOS process. The developed library provides four structural variations that are most popular in RFIC design; standard spiral structure, patterned ground shield(PGS) structure to enhance quality factor, stacked structure to enable high inductance values in a given silicon area, multilayer structure to lower series resistance. Electromagnetic simulation, equivalent circuit, and parameter extraction processes have been verified based on measurement results. The extensive measurement and simulation results of the inductor library can be a great asset for low cost RFIC design and development.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.10
• /
• pp.941-944
• /
• 2016

This paper proposes 24 GHz power amplifier for automotive collision avoidance and surveillance short range radar using Samsung 65-nm CMOS process. The proposed circuit has a 2-stage differential power amplifier which includes common source structure and transformer for single to differential conversion, impedance matching, and power combining. The measurement results show 15.5 dB maximum voltage gain and 3.6 GHz 3 dB bandwidth. The measured maximum output power is 13.1 dBm, input $P1_{dB}$ is -4.72 dBm, output $P1_{dB}$ is 9.78 dBm, and maximum power efficiency is 17.7 %. The power amplifier consumes 74 mW DC power from 1.2 V supply voltage.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.396-397
• /
• 2011

This paper has proposed a multi-channel low pass filter (LPF) for LTE-Advanced systems. The proposed LPF is an active-RC 5th chebyshev topology with three cut-off frequencies of 5 MHz, 10 MHz, and 40 MHz. A 3-bit tuning circuit has been adopted to prevent variations of each cut-off frequency from process, voltage, and temperature (PVT). To achieve a high cut-off frequency of 40 MHz, an operational amplifier used in the proposed filter has employed a PMOS cross-connection load with a negative impedance. A proposed filter has been implemented in a $0.13-{\mu}m$ CMOS technology and consumes 20.2 mW with a 1.2V supply voltage.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.6
• /
• pp.726-732
• /
• 2019

In this study, we proposed an asymmetric differential inductor to improve the linearity of differential power amplifiers. Considering the phase error between differential signals of the differential amplifier, the location of the center tap of the differential inductor was modified to minimize the error. As a result, the center tap was positioned asymmetrically inside the differential inductor. With the asymmetric differential inductor, the AM-to-AM and AM-to-PM distortions of the amplifier were suppressed. To confirm the feasibility of the inductor, we designed a 2.4 GHz differential CMOS PA for IEEE 802.11n WLAN applications with a 64-quadrature amplitude modulation (QAM), 9.6 dB peak-to-average power ratio (PAPR), and a bandwidth of 20 MHz. The designed power amplifier was fabricated using the 180-nm RF CMOS process. The measured maximum linear output power was 17 dBm, whereas EVM was 5%.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.5
• /
• pp.109-114
• /
• 2023

In this paper, a 2-channel Image-Reject receiver using a 65-nm CMOS process is presented for Ka-band compact radars. The designed receiver consists of Low-Noise Amplifier (LNA), IQ mixer, and Analog Baseband (ABB). ABB includes a complex filter in order to suppress unwanted images, and the variable gain amplifiers (VGAs) in RF block and ABB have gain tuning range from 4.5-56 dB for wide dynamic range. The gain of the receiver is controlled by on-chip SPI controllers. The receiver has noise figure of <15 dB, OP1dB of >4 dBm, image rejection ratio of >30 dB, and channel isolation of >45 dB at the voltage gain of 36 dB, in the Ka-band target frequency. The receiver consumes 420 mA at 1.2 V supply with die area of 4000×1600 ㎛.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.10
• /
• pp.2369-2379
• /
• 2013

A CMOS x-ray line scan sensor which is used in both medical imaging and non-destructive diagnosis is designed. It has a pixel array of 512 columns ${\times}$ 4 rows and a built-in DC-DC converter. The pixel circuit is newly proposed to have three binning modes such as no binning, $2{\times}2$ binning, and $4{\times}4$ binning in order to select one of pixel sizes of $100{\mu}m$, $200{\mu}m$, and $400{\mu}m$. It is designed to output a fully differential image signal which is insensitive to power supply and input common mode noises. The layout size of the designed line scan sensor with a $0.18{\mu}m$ x-ray CMOS image sensor process is $51,304{\mu}m{\times}5,945{\mu}m$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.6
• /
• pp.591-600
• /
• 2010

In this paper, three kinds of 24 GHz low-power CMOS cross-coupled voltage controlled oscillators are designed and fabricated for a short-range radar applications using TSMC 0.13 ${\mu}m$ CMOS process. The basic CMOS crosscoupled voltage controlled oscillator is designed for oscillating around a center frequency of 24.1 GHz and subthreshold oscillators are developed for low power operation from it. A double resonant circuit is newly applied to the subthreshold oscillator to improve the problem that parasitic capacitance of large transistors in a subthreshold oscillator can push the oscillation frequency toward lower frequencies. The fabricated chips show the phase noise of -101~-103.5 dBc/Hz at 1 MHz offset, the output power of -11.85~-15.33 dBm and the frequency tuning range of 475~852 MHz. In terms of power consumption, the basic oscillator consumes 5.6 mW, while the subthreshold oscillator does 3.3 mW. The subthreshold oscillator with the double resonant circuit shows relatively lower power consumption and improved phase noise performance while maintaining a comparable frequency tuning range. The subthreshold oscillator with double resonances has FOM of -185.2 dBc based on 1 mW DC power reference, which is an about 3 dB improved result compared with the basic oscillator.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.7 s.361
• /
• pp.41-46
• /
• 2007

A novel post-linearization technique is proposed for CMOS cascode low noise amplifier (LNA). The technique uses dual common gate FETs one of which delivers the linear currents to a load and the other one sinks the $3^{rd}$ order intermodulation currents of output currents from the common source FET. Selective current branching can be implemented in $0.18{\mu}m$ CMOS process by using a thick oxide FET as an IM3 sinker with a normal FET as a linear current buffer. A differential LNA adopting this technique is designed at 2.14GHz. The measurement results show 11dBm IIP3, 15.5dB power gain and 2.85dB noise figure consuming 12.4mA from 1.8V power supply. Compared with the LNA with turning off the IM3 sinker, the proposed technique improves the IIP3 by 7.5 dB.