• Journal of the Optical Society of Korea
• /
• v.13 no.4
• /
• pp.434-438
• /
• 2009

In this paper, a 12.5-Gb/s optical transmitter is implemented using 0.13-${\mu}m$ CMOS technology. The optical transmitter that we constructed compensates temperature effects of VCSEL (Vertical cavity surface emitting laser) using auto-power control (APC) and auto-modulation control (AMC). An external monitoring photodiode (MPD) detects optical power and modulation. The proposed APC and AMC demonstrate 5$\sim$20-mA of bias-current control and 5$\sim$20-mA of modulation-current control, respectively. To enhance the bandwidth of the optical transmitter, an active feedback amplifier with negative capacitance compensation is exploited. The whole chip consumes only 140.4-mW of DC power at a single 1.8-V supply under the maximum modulation and bias currents, and occupies the area of 1280-${\mu}m$ by 330-${\mu}m$ excluding bonding pads.

• ETRI Journal
• /
• v.31 no.5
• /
• pp.576-584
• /
• 2009

A novel tunable transconductor is presented. Input transistors operate in the triode region to achieve programmable voltage-to-current conversion. These transistors are kept in the triode region by a novel negative feedback loop which features simplicity, low voltage requirements, and high output resistance. A linearity analysis is carried out which demonstrates how the proposed transconductance tuning scheme leads to high linearity in a wide transconductance range. Measurement results for a 0.5 ${\mu}m$ CMOS implementation of the transconductor show a transconductance tuning range of more than a decade (15 ${\mu}A/V$ to 165 ${\mu}A/V$) and a total harmonic distortion of -67 dB at 1 MHz for an input of 1 Vpp and a supply voltage of 1.8 V.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.12
• /
• pp.2503-2510
• /
• 2015

This paper presents a single-phase energy measurement IC to measure electric power quantities. The entire IC includes two programmable gain amplifiers (PGAs), two ${\sum}{\Delta}$ modulators, a reference circuit, a low-dropout (LDO) regulator, a temperature sensor, a filter unit, a computation engine, a calibration control unit, registers, and an external interface block. The proposed energy measurement IC is fabricated with $0.18-{\mu}m$ CMOS technology and housed in a 32-pin quad-flat no-leads (QFN) package. It operates at a clock speed of 4,096 kHz and consumes 10 mW in 3.3 V supply.

• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.305-308
• /
• 2002

An 1.8V 6bit IGSPS ADC for high speed data acquisition is discussed in this paper. This ADC is based on a flash ADC architecture because the flash ADC is the only practical architecture at conversion rates of IGSPS and beyond. A straightforward 6bit full flash A/D converter consists of two resistive ladders with 63 laps, 63 comparators and digital blocks. One important source of errors in flash A/D converter is caused by the capacitive feedthrough of the high frequency input signal to the resistive reference-lauder. Consequently. the voltage at each tap of the ladder network can change its nominal DC value. This means large transistors have a large parasitic capacitance. Therefore, a dual resistive ladder with capacitor is employed to fix the DC value. Each resistive ladder generates 32 clean reference voltages which alternates with each other. And a two-stage amplifier is also used to reduce the effect of the capacitive feedthrough by minimizing the size of MOS connected to reference voltage. The proposed ADC is based on 0.18${\mu}{\textrm}{m}$ 1-poly 6-metal n-well CMOS technology, and it consumes 307㎽ at 1.8V power supply.

• Journal of Sensor Science and Technology
• /
• v.6 no.2
• /
• pp.145-154
• /
• 1997

Based on a new search strategy using circuit simulation and simulated annealing with local search, a technique for design automation of high-performance operational amplifiers is proposed. For arbitrary circuit topology and performance specifications, through discrete optimization of a cost function with discrete design variables the design of operational amplifiers is performed. A special-purpose circuit simulator and some heuristics are used to reduce the design time. Through the design of a low-power high-speed fully differential CMOS operational amplifier usable in smart sensors and 10-b 25-MS/s pipelined A/D converters, it has been demonstrated that a design tool developed using the proposed technique can be used for designing high-performance operational amplifiers with less design knowledge and less design effort.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.20 no.2
• /
• pp.63-74
• /
• 2024

This Paper presents a resistive wideband fully differential low-noise amplifier (LNA) designed using a noise-cancellation technique for TV tuner applications. The front-end of the LNA employs a cascode common-gate (CG) configuration, and cross-coupled local feedback is employed between the CG and common-source (CS) stages. The moderate gain at the source of the cascode transistor in the CS stage is utilized to boost the transconductance of the cascode CG stage. This produces higher gain and lower noise figure (NF) than a conventional LNA with inductor. The NF can be further optimized by adjusting the local open-loop gain, thereby distributing the power consumption among the transistors and resistors. Finally, an optimized DC gain is obtained by designing the output resistive network. The proposed LNA, designed in SK Hynix 180 nm CMOS, exhibits improved linearity with a voltage gain of 10.7 dB, and minimum NF of 1.6-1.9 dB over a signal bandwidth of 40 MHz to 1 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.3
• /
• pp.358-365
• /
• 2008

A differential-gain-controlled LNA is designed and implemented in 0.18 um CMOS technology for $3.1{\sim}4.8GHz$ UWB system. In high gain mode, measurements show a differential power gain of $14.1{\sim}15.8dB,\;13.3{\sim}15dB$, respectably, an input return loss higher then 10dB, an input IP3 of -19.3 dBm, a noise figure of $4.85{\sim}5.09dB$, while consuming only 19.8 mW of power from a 1.8V DC supply. In low gain mode, measurements show a differential power gain of $-6.1{\sim}-4.2dB,\;-7.6{\sim}-5.6dB$, respectably, an input return loss higher then 10dB, an input IP3 of -1.45 dBm, a noise figure of $8.8{\sim}10.3dB$, while consuming only 5.4mW of power from a 1.8V DC supply.

• Journal of IKEEE
• /
• v.22 no.4
• /
• pp.1025-1030
• /
• 2018

The proposed modulator is designed by utilizing a conventional structure employing time division technique to realize the 4th order delta-sigma modulator using one op-amp. In order to reduce the influence of KT/C noise, the capacitance in the first and second integrators reused was chosen to be 20pF and capacitance of third and fourth integrators was designed to be 1pF. The stage variable technique in the low power reconfigurable op-amp was used to solve the stability issue due to different capacitance loads for the reduction of KT/C noise. This technique enabled the proposed modulator to reduce the power consumption of 15% with respect to the conventional one. The proposed modulator was fabricated with 0.18um CMOS N-well 1 poly 6 metal process and consumes 305uW at supply voltage of 1.8V. The measurement results demonstrated that SNDR, ENOB, DR, FoM(Walden), and FoM(Schreier) were 66.3 dB, 10.6 bits, 83 dB, 98 pJ/step, and 142.8 dB at the sampling frequency of 256kHz, oversampling ratio of 128, clock frequency of 1.024 MHz, and input frequency of 250 Hz, respectively.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.11 no.2
• /
• pp.97-105
• /
• 2016

Microcontrollers (MCUs) for endpoint smart sensor devices of internet-of-thing (IoT) are being implemented as system-on-chip (SoC) with on-chip instruction flash memory, in which user firmware is embedded. MCUs directly fetch binary code-based instructions through bit-line sense amplifier (S/A) integrated with on-chip flash memory. The S/A compares bit cell current with reference current to identify which data are programmed. The S/A in reading '0' (erased) cell data consumes a large sink current, which is greater than off-current for '1' (programmed) cell data. The main motivation of our approach is to reduce the number of accesses of erased cells by binary code level transformation. This paper proposes a built-in write/read path architecture using binary code inversion method based on hot-spot region detection of instruction code access to reduce sensing current in S/A. From the profiling result of instruction access patterns, hot-spot region of an original compiled binary code is conditionally inverted with the proposed bit-inversion techniques. The de-inversion hardware only consumes small logic current instead of analog sink current in S/A and it is integrated with the conventional S/A to restore original binary instructions. The proposed techniques are applied to the fully-custom designed MCU with ARM Cortex-M0$^{TM}$ using 0.18um Magnachip Flash-embedded CMOS process and the benefits in terms of power consumption reduction are evaluated for Dhrystone$^{TM}$ benchmark. The profiling environment of instruction code executions is implemented by extending commercial ARM KEIL$^{TM}$ MDK (MCU Development Kit) with our custom-designed access analyzer.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.9 no.1
• /
• pp.22-28
• /
• 2009

This paper presents a fast received signal strength indicator (RSSI) circuit for wireless communication application. The proposed circuit is developed using power detectors and an analog-to-digital converter to achieve a fast settling time. The power detector is consisted of a novel logarithmic variable gain amplifier (VGA), a peak detector, and a comparator in a closed loop. The VGA achieved a wide logarithmic gain range in a closed loop form for stable operation. For the peak detector, a fast settling time and small ripple are obtained using the orthogonal characteristics of quadrature signals. In $0.18-{\mu}m$ CMOS process, the RSSI value settles down in $20{\mu}s$ with power consumption of 20 mW, and the maximum ripple of the RSSI is 30 mV. The proposed RSSI circuit is fabricated with a personal handy-phone system transceiver. The active area is $0.8{\times}0.2\;mm^2$.