• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.17-48
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic\ulcorneriency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet\ulcornerween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr\ulcornerease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$ $$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$ The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$ These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea\ulcornerses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin\ulcornerear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num\ulcornerber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco\ulcornervery rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.3
• /
• pp.335-340
• /
• 2010

This study was conducted to select organic materials (OM) and nitrogen sources in composting of waste mushroom bed from Agaricus bisporus. We examined physio-chemical properties of the organic materials and the mixture ratio for preparing the wasted mushroom bed (M) compost. The carbon content of sawdust was higher than those of rice straw (R) as OM source and the nitrogen content was high in the order of fowl manure (F)>> pig manure (P)> cow manure (C). The compost was prepared to maintain the criteria of above 25% organic matter and then the change of their ingredients was estimated during the process of fermentation. The temperature of waste mushroom bed+pig manure+rice straw (MRP) treatment was varied fast throughout fermentation, on the other hand the temperature of waste mushroom bed+pig manure+sawdust (MSP) treatment was steadily elevated to the middle of composting. The pH of the compost was somewhat high to pH 8.5~9.0 at the early stage, but decreased to 7.5 at the end stage of composting. The content of OM after fermentation was decreased to the level of 19~21% in rice straw, but the sawdust treatment maintained 25~27% organic matter. The waste mushroom bed+fowl manure+rice straw (MRF) treatment, which contains 26.2% organic matter and 0.68% nitrogen, was the highest among them. The volume of compost was reduced to 50% by using rice straw as organic matter, but reduced to 30% by using the sawdust. The contents of heavy metal in the compost were suitable within the legal criteria. The number of microorganisms were higher in the rice straw than those in the sawdust. It was high in the order of fowl manure> pig manure> cow manure. The major groups consisted of aerobic bacteria, gram negative bacteria and Bacillus sp. and their populations after fermentation were increased to $1{\times}10^1{\sim}1{\times}10^2\;cfu\;g^{-1}$ rather than those before fermentation. Therefore we concluded that the waste mushroom bed+fowl manure+sawdust (MSF 3:9:1 v/v/v) treatment was suitable combination for high organic matter and nitrogen source, and the periods of composting were 50~60 days.

• Korean Journal of Soil Science and Fertilizer
• /
• v.27 no.3
• /
• pp.168-178
• /
• 1994

Acid sulfate soils occur extensively in Gimhae area where they have been formed from the brackish alluvial sediments along the sea coast and river estuary. The strong acid environment enhances silicate weathering and thus affects the soil clay minerals. The minerals were identified through chemical, X-ray diffraction and thermal methods. The ratio of $SiO_2$ and $Al_2O_3$ in the clay fractions ranged from 3.14 to 3.77, indicating that the distribution of the clay minerals were 1 : 1 and 2 : 1 minerals. Cation exchange capacity in the clay fractions was low due to high contents of 1 : 1 minerals and hydroxy interlayered vermiculite(HIV). The B and C horizon rich in jarosite have large amounts of yellow streaks which reflect high content of $Fe_2O_3$ and $K_2O$. Vermiculite and illite were quantified from thermogravimetry(TG), kaolin minerals from both TG and differential thermal analysis(DTA), and HIV from X-ray diffraction analysis. The dominant clay minerals were kaolin minerals, vermiculite, illite and HIV. HIV considered to be formed, especially, in acid soil environments. The minor minerals were quarts, feldspar, jarosite, pyrite, hematite and goethite. Kaolin minerals were the most abundant clay minerals throughout the acid sulfate soil. Kaolin minerals, however, increased towards the top of horizons throughout the soils and HIV decreased towards the top of horizons in the soil of Gimhae series and Haecheog series. Alteration of HIV to kaolin minerals during weathering of low pH condition in deep soil horizons may explain the high quantities of kaolin minerals and the relatively low quantities of HIV in the soil at top horizons.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.12 no.3
• /
• pp.191-200
• /
• 1979

For the use of antarctic krill as a fond protein source its compositional characteristics were investigated as the first part of the work includes other subjects such as processing of drill paste, concentrates, and fermented or seasoned product. In general composition of fresh frozen and preboiled frozen krill on board, the contents of crude fat and free amino nitrogen were higher in the former than in the latter which contained a high amount of ash. VBN was rather high as much as 37.6 and $26.4\;mg\%$ in both fresh frozen and preboiled krill. The pH of drill homogenates was 7.1 to 7.2 in both cases. Such a low pH might be attributed to a long term storage and temperature fluctuations during frequent transshipping. The amino acid competition of fresh frozen krill meat showed relatively high amount of glutamic acid, aspartic acid, lysine, proline, and leucine while methionine, histidine, serine, tyrosine, and phenylalanine were lower. Among the essential amino acids lysine and leucine were higher and methionine was lower. In tile composition of free amino acid proline, lysing, arginine, and alanine were higher comparatively to the contents of histidine, aspartic acid, serine, and threonine. It is noteworthy for nutritional qualification that tile essential amino acids particularly as lysine were abundant similarly to that of fishes. Heavy metal contents of krill meat 0.039 to 0.048 ppm as Hg, 0.06 to 0.11 ppm as Pb, less than 0.32 ppm as Zn, 0.008 to 0.012 ppm as Cd, 0.61 to 0.68 ppm as Fe, 0.87 to 1.37 ppm as Cu, and nondetective as Cr. A high Cu content seems to be resulted by tile blood pigment of crustacea. The ratio,1 of edible portion to non-edible portion were 37:63 in fresh frozen and 42:58 in preboiled frozen krill respectively. Release of drip after thawing was more in fresh frozen than in preboiled frozen drill marking $36\%$ and $24\%$ of both respectively.

• Journal of the Korean Arthroscopy Society
• /
• v.3 no.2
• /
• pp.115-120
• /
• 1999

Purpose : After the total or partial meniscectomy of the lateral discoid meniscus, many patients complain the residual pain or the recurrent symptoms of the meniscus, and some of them need reoperation. We analyzed the causes of the reoperation after initial meniscectomy. Material & Method : Two hundred seventy three patients with the symptomatic lateral discoid meniscus were treated by arthroscopic meniscectomy between October, 1989 and September, 1998. Of the 273 patients, 69 patients were treated by total meniscectomy and 204 patients were treated by partial meniscectomy. The male to female sex ratio was 1:1.04, and the average of the age was 23.1 years old(from 4 to 59 years old). The reoperation was done in 8 patients, of which 1 was the case of total meniscectomy at the initial operation, and the rest 7 were the case of partial meniscectomy. Results : Of the 8 reoperations, 3 patients recurred the meniscal symptoms within the 3rd week after the initial operation, and 5 patients recurred beyond the 3rd week after the initial operation. Among the 3 patients of carly recurrence, 2 patients showed inadequate sizes of the remnant meniscus, and 1 patient showed posterolateral instability of the remained meniscus. Among the 5 patients of late recurrence, 3 patients showed rerupture of the meniscus, and 2 patients showed associated pathology of degenerative arthritis following osteochondritis dissecans. Conclusions : The reoperation rate after initial meniscectomy of the lateral discoid meniscus was higher in partial meniscectomy than total meniscectomy. During the operation of the lateral discoid meniscus, we must determine the adequate resectional margin, confirm the remnant meniscus by probing, and look for the associated pathologies.

• Food Science of Animal Resources
• /
• v.25 no.4
• /
• pp.430-435
• /
• 2005

Current study was conducted to investigate the effect of organic selenium supplementation originated from mushroom culture medium on meat quality of Hanwoo sleets. The result showed that organic selenium supplementation of 0.9 ppm (DM based ratio) for 2 (T1), 4 (T2) and 6 (T3) months had no effect on moisture content in longissimus muscle, with 63 to $66\%$ compared to non-supplemented control group Similarly, intramuscular fat content ranged from 11.7 to $16.4\%$ did not differ between the treatment groups (p>0.05). T3 group showed the highest protein content with $20.8\%$ while T2 group had the lowest content with $19.2\%$ The data indicated that organic selenium supplementation to the experimental concentration had indictable effect on proximate composition The treatments similarly had no influence on physical and biological characteristics of longissimus muscle, where cooking loss and shear force ranged from 20 to $21\%$ and from 3.6 to 4.4kg, respectively. On the other hand, muscle pH at 24 h postmortem showed 5.52, 5.57, 5.50, 5.50 for control, T1, T2 and T3, respectively, indicating that the longer feeding period resulted in the lower ultimate un A similar trend was observed from water-holding capacity (63.8, 64.4 and $64.2\%$ for T1, T2 and T3, respectively) which was significantly higher than con01 group of $59.5\%$ For sensory evaluation, juiciness did not differ between the treatment groups, but n and n (5.30 and 5.28, respectively) showed significantly tender mat Particularly, T2 group received significantly higher flavor score among the treatment groups including controls. The data indicated that organic selenium supplementation to the experimental concentration had no effect on beef quality, but the treatment effect on anti-oxidation function is remained for further studies.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.16 no.2
• /
• pp.88-101
• /
• 2013

The International Convention for the Control and Management of Ship's Ballast Water and Sediments was adopted at 2004 and then various BWMS (ballast water management system) have been developed. In this study, WET (whole effluent toxicity) test with algae (diatom) Skeletonema costatum as primary producer, invertebrate (rotifera) Brachionus plicatilis as 1st consumer and fish (olive flounder) Paralichthys olivaceus as predator, chemical analysis and ERA (environmental risk assessment) were conducted to assess the unacceptable effect on marine ecosystem by emitting the discharge water treated with AquaStar$^{TM}$ BWMS using electrolysis as main treatment equipment for removing the marine organisms in the ship's ballast water. The most sensitive test organism on discharge water treated with AquaStar$^{TM}$ BWMS was S. costatum that gave the NOEC value of 25.00%, LOEC value of 50.00% and 72hr-$EC_{50}$ value of 69.97% from WET test result for 20 psu salinity treated discharge water. NOEC and LOEC value of B. plicatilis and P. olivaceus exposed at 20 psu salinity treated discharge water were 50.00% and 100.00%, respectively. In the chemical analysis results, total number of substances produced by AquaStar$^{TM}$ BWMS was 18 which were bromate, 7 volatile halogenated organic compounds, 7 halogenated acetic acids, 3 halogenated acetonitriles and chloropicrin. Eighteen substances did not consider as persistence and bioaccumulative chemicals. Uncertainty of toxic property of 18 substances was high. PECs of 18 substances calculated by MAMPEC model were ranged from $4.58{\times}10^{-4}$ to $4.87{\mu}g\;L^{-1}$, PNECs of them were ranged from $1.6{\times}10^{-2}$ to $3.2{\times}10^2{\mu}g\;L^{-1}$. And, the PEC/PNEC ratio of 18 substances did not exceed 1. Therefore, ERA for produced substances indicate that the discharge water treated with AquaStar$^{TM}$ BWMS does not pose unacceptable effect on marine life. And $EC_{50}$ value of S. costatum on discharge water treated by BWMS using the electrolysis had positive correlation with initial TRO concentration, concentration and kind & level of HAAs.

• Korean Journal of Microbiology
• /
• v.44 no.3
• /
• pp.237-243
• /
• 2008

Chemical and microbial characteristics of bacterial populations were investigated in a quercus and pine humus forest soil. Soil pH was $5.3\pm0.4$ and $4.1\pm0.9$ from each sample of a quercus and pine humus forest soil; C/N ratio of humus forest soil was $17.84\pm4.6%$ and $21.76\pm8%$, respectively. Total organic acid was investigated as 69.57 mM/g dry soil and 53.72 mM/g dry soil in each humus forest soil. Glutamine, pyruvate, succinate, lactic acid and acetic acid of pine humus forest soil were $1.5\sim4.5$ times higher than those of quercus humus forest soil. As we evaluated phylogenetic characteristics of bacterial populations by 16S rRNA-ARDRA analysis with DNA extracted from each humus forest soil. Based on the 16S rRNA sequences, 44 clone from ARDRA groups of quercus humus forest soil were classified into 7 phyla: ${\alpha},{\beta},{\gamma},{\delta}$-Proteobacteria, Acidobacteria, Actinobacteria, and Firmicutes. Thirty-two clone from ARDRA groups of pine humus forest soil were classified into 8 phyla: ${\alpha},{\beta},{\gamma}$-Proteobacteria, Acidobacteria, Bacteroides, Verrucomicrobia, Planctomycetes, and Gemmatomonadetes. According to PCA (Principal Component Analysis) based on 16S rRNA base sequence, there were three main groups of bacteria. All clone of Cluster I were originated from quercus humus forest soil, while 67% clone of Cluster II and 63% clone of Clusters III were separated from pine humus forest soil.

• Journal of Embryo Transfer
• /
• v.20 no.2
• /
• pp.169-176
• /
• 2005

Loop-mediated isothermal amplification (LAMP) is novel DNA amplification methods that amplifies a target sequence specifically under isothemal condition. The present study was to assess the in vitro viability afier biopsy and sexing rate of different types of embryo biopsied. In vivo compact morulae and blastocyst embryos were obtained from Korean Native Cow (KNC) superovulated with FSH (Antorin, R-10) on 7 Day after artificial insemination. in vitro compact morulae and blastocyst embryos were obtained with KNC or Holsteins that were gained on 6, 7 or 8 day after in vitro fertilization(IVF) with frozen semen. Biopsy of bovine embryo was carried out in a $80{\mu}l$ drop with $Ca^{2+}-Mg^{2+}$ free D-PBS and the viability of biopsied embryos were evaluated in IVMD (IFP, Japan) medium at 12 hrs culture time. The sex ratio of biopsied Hanwoo embryos were male vs. female of $43.5\%\;vs.\;56.5\%$ in vivo and $33.9\%\;vs.\;49.2\%$ in vitro respectively, and male rate of biopsied Holstein embryos were significantly higher than female $(70.8\;vs.\;29.2\%)$. and indefinite rate of in vitro embryos was $16.9\%$ and in vivo was not. The degeneration rate of biopsied embryo, in vitro embryos were significantly higher than in vivo $(13.2\%\;vs,\;0.0\%,\;p<0.05)$. The survivability of in vivo embryo were between biopsied following punching method was significantly (P<0.05) higher than bisection method produced embryos $(100\%\;vs.\;83.3\%)$ and in vitro had no difference. However, the degeneration rate of biopsied embryo by bisection method was significantly higher than punching methods between in vivo and in vitro $(16.7\;vs.\;22.6\%,\;respectively,\;p<0.05)$. In conclusion, these results indicate that punching method was optimal and survivability after embryo biopsy was useful for reducing the damage caused by the embryo biopsy procedure for LAMP-based embryo sexing.

• Asian-Australasian Journal of Animal Sciences
• /
• v.27 no.7
• /
• pp.1003-1012
• /
• 2014

The use of a suitable methodology to quantify the phytate phosphorus ($P_{phy}$) content in both the feed and the excreta from broilers is required to enable accurate calculation of the catalytic efficiency of the phytase supplemented in the feed. This study was conducted to compare 2 analytical methodologies (colorimetry and also high-performance liquid chromatography with a refractive index detector) in order to calculate the phytase efficiency by utilizing the results from the methodology that was shown to be the most appropriate. One hundred and twenty broilers were distributed in a $(4+1){\times}2$ factorial arrangement, corresponding to 4 diets that were equally deficient in P supplemented with increasing levels of phytase (0, 750, 1,500, and 2,250 units of phytase activity - FTU - per kg of feed) plus 1 positive control diet without phytase, supplied to male and female birds. The result indicated that the colorimetric methodology with an extraction ratio of 1:20 (mass of sample in g:volume of the solvent extractor in mL) was shown to be the most adequate. There was no interaction between the phytase level and the sex of the broilers (p>0.05). Males consumed 12% more $P_{phy}$ than did females (p<0.01), but the sex of the broilers did not affect (p>0.05) the excretion and retention coefficient of $P_{phy}$. The increase in the phytase level of the diet reduced (linear, p<0.01) the $P_{phy}$ excretion. The greatest $P_{phy}$ retention was estimated at 87.85% when the diet contained 1,950 FTU/kg (p<0.01), indicating that it is possible to reduce the inorganic P in the formulation at an amount equivalent to 87.85% of the $P_{phy}$ content present in the feed, which, in this research, corresponds to a decrease in 2.86 g of P/kg of the feed.