• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.10
• /
• pp.1612-1620
• /
• 2004

This study presents methods to estimate elastic-plastic crack opening displacement (COD) fur circumferential through-wall cracked pipes for the Leak-Before-Break (LBB) analysis of pressurized piping. Proposed methods are based not only on the GE/EPRI approach but also on the reference stress approach. For each approach, two different estimation schemes are given, one for the case when full stress-strain data are available and the other fur the case when only yield and ultimate tensile strengths are available. For the GE/EPRI approach a robust way of determining the Ramberg-Osgood (R-O) parameters is proposed, not only fur the case when detailed information on full stress-strain data is available but also for the case when only yield and ultimate tensile strengths are available. The COD estimates according to the GE/EPRI approach, using the R-O parameters determined from the proposed R-O fitting procedures, generally compare well with the published pipe test data. For the reference stress approach, the COD estimates according to the method based on both full stress-strain data and limited tensile properties are in good agreement with pipe test data. In conclusion, experimental validation given in the present study provides sufficient confidence in the use of the proposed method to practical LBB analyses even though when information on material's tensile properties is limited.

• Korean Journal of Applied Biomechanics
• /
• v.27 no.4
• /
• pp.269-278
• /
• 2017

Objective: The purpose of this study was to develop a goal setting method for increasing the probability of a holed in a side inclined putting stroke. Method: Three-dimensional video data was recorded at a frequency of 120 hz per second after synchronizing 19 infrared motion capture systems (Qualisys, Gothenburg, Sweden). Putting green used a polycarbonate plate ($1.2{\times}2.4{\times}0.01meter$) with coefficient of friction (${\mu}=0.062$) and a real curve of the actual hole. Results: The velocity ratio between the club and the ball was 1:1.6 under various ball speed conditions in this study. The overall position of the break is 1 m to 1.4 m from the point where the ball leaves. If there is a slope, the ball follows the target line by the straightening force, and when it reaches 1 m position, the straightening force decreases by 30~50% and reaches to the deviation (break) point which is severely influenced by the slope. From here, the ball is aimed in a direction other than the target, and the size is affected by the slope. Conclusion: If there is a side slope, the ball moves away from the straight line, and the larger the slope, the closer the break point is to the starting point of the ball. Therefore, it is necessary to calculate the degree of departure according to the slope carefully, and it is preferable that the slower the speed is, the more the influence of the slope becomes. It is preferable to use the center of the hole as a reference when calculating the departure.

• Journal of Korea Water Resources Association
• /
• v.44 no.3
• /
• pp.249-262
• /
• 2011

In this study, in order to reduce the numerical oscillation due to the unbalance between source and flux terms as the HLLC scheme is applied to the flow analysis on the irregular bed topography, a unstructured finite volume model based on the well-balanced HLLC scheme and the shallow water equations is developed and applied to problems of dam-break waves. The well-balanced HLLC scheme considers directly the gradient of bed topography as the flux terms is calculated. This scheme provides the good numerical balance between the source and flux terms in the case of the application to the steady-state transcritical flow. To verify the numerical model developed in this study, it is applied to three cases of hydraulic model experiments and a field case study of Mapasset dam failure (France). As a result of the verification, the predicted numerical results agree relatively well with available laboratory and field measurements. The model provides slightly more accurate results compared with the existing models.

• Journal of Astronomy and Space Sciences
• /
• v.34 no.4
• /
• pp.289-302
• /
• 2017

The key risk analysis technologies for the re-entry of space objects into Earth's atmosphere are divided into four categories: cataloguing and databases of the re-entry of space objects, lifetime and re-entry trajectory predictions, break-up models after re-entry and multiple debris distribution predictions, and ground impact probability models. In this study, we focused on reentry prediction, including orbital lifetime assessments, for space situational awareness systems. Re-entry predictions are very difficult and are affected by various sources of uncertainty. In particular, during uncontrolled re-entry, large spacecraft may break into several pieces of debris, and the surviving fragments can be a significant hazard for persons and properties on the ground. In recent years, specific methods and procedures have been developed to provide clear information for predicting and analyzing the re-entry of space objects and for ground-risk assessments. Representative tools include object reentry survival analysis tool (ORSAT) and debris assessment software (DAS) developed by National Aeronautics and Space Administration (NASA), spacecraft atmospheric re-entry and aerothermal break-up (SCARAB) and debris risk assessment and mitigation analysis (DRAMA) developed by European Space Agency (ESA), and semi-analytic tool for end of life analysis (STELA) developed by Centre National d'Etudes Spatiales (CNES). In this study, various surveys of existing re-entry space objects are reviewed, and an efficient re-entry prediction technique is suggested based on STELA, the life-cycle analysis tool for satellites, and DRAMA, a re-entry analysis tool. To verify the proposed method, the re-entry of the Tiangong-1 Space Lab, which is expected to re-enter Earth's atmosphere shortly, was simulated. Eventually, these results will provide a basis for space situational awareness risk analyses of the re-entry of space objects.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.39 no.1
• /
• pp.98-102
• /
• 1994

This study was conducted to obtain basic informations on the starch quality improvement breeding of Job's tears. Starch, amylose, gel consistency and amylogram characteristics of seeds were investigated in 36 varieties of domestic and introduced Job's tears. Starch content was distributed between 50.9 and 78% with a mean of 60.5%. The variation observed in amylose content ranged from 0 to 7.2% with the average was 5.2%. Kangsanjong, Chujeonjong, Chungrijong showed medium gel consistency. However, many Job's tears tested showed soft gel consistency. Varietal differences of amylogram characteristics was also found at break down. In general, job's tear starch showed lower value of setback.

• Journal of Korean Ophthalmic Optics Society
• /
• v.8 no.2
• /
• pp.47-52
• /
• 2003

117 undergraduate ophthalmic optics students volunteered to participate in this study. They ranged in age from 19 to 26 years. Subject, had best corrected visual acuity of at least 1.0 in both eyes, no strabismus, no amblyopia, and no history of ocular surgery. 37 subjects are esphoria and 25 subjects are $3{\Delta}$ and less, and the rest of 12 subjects show more $4{\Delta}$. Average phoria amount is $2.96{\Delta}$ at far distance and $1.08{\Delta}$ at near distance, respectively. The variation of phoria amount in far and near distance, unchanging subjects are 3, 8 subjects are increase esophoria amount, and 26 subjects are phoria amount decreasing or appear exophoria. The reason of esophoria amount is decreasing in near distance, and the results are convergence burden decreases. At positive relative convergence, the expected value in far distance, blurred point is 7, break point is 16, and recovery point is 12. And negative relative convergence, break point is 7 and recovery point is 13, respectively. Moreover, at positive relative convergence, the expected value in near distance is blurred point is 8, break point is 7 and recovery point is 22. And negative relative convergence, blurred point is 2, break point is 8 and recovery point is 12, respectively.

• Environmental and Resource Economics Review
• /
• v.26 no.2
• /
• pp.123-138
• /
• 2017

This study estimates the effect of the Kyoto Protocol on $CO_2$ emissions with a Quandt-Andrews test for detection of structural break with Annex B counties data. The structural break on $CO_2$ emissions took place in 2008 which is 3 year after ratification of the Kyoto Protocol. According to the empirical results, 1% increase in energy consumption leads to 1% and 0.31% increases in income before and after the structural break, respectively. This study also finds the monotonic increase relationship between $CO_2$ emission and income. Regarding to the relationship between renewable energy use and $CO_2$ emissions, 1% increase in renewable energy consumption leads to 0.1% decrease in $CO_2$ emissions until year 2007 and 0.09% decreases after year 2008, respectively. Based on the results of empirical study, we find little evidence of the effect of the Kyoto Protocol on reduction of $CO_2$ emissions for Annex B countries.

• Journal of Korean Ophthalmic Optics Society
• /
• v.15 no.4
• /
• pp.339-346
• /
• 2010

Purpose: The study was performed to compare the difference of non-invasive tear break-up time (NIBUT) with alignment or steep fitting of soft contact lens in normal and dry eyes. Methods: Total 40 eyes (aged 20~30 years) were classified to the normal (n=20) or dry eye group (n=20) by the diagnosis methods for dry eyes and worn soft contact lens (polymacon material) with alignment or steep fitting. NIBUTs of lens wearers were separately measured at the points of before wearing, immediately after wearing and after stabilization of tear film. Results: With alignment fitting, averaged NIBUT in the dry eye group after stabilization of tear film was not significantly different from that of the normal eye group. However, averaged NIBUTs in the normal and dry eyes had significant difference when measured immediately after lens wearing. However, the number of eyes having NIBUT less than 4.0 second was 30% higher compared to the number of normal eyes with steep fitting when measured immediately after wearing. Some shorten NIBUT in dry eyes with steep fitting was also shown after stabilization of tear film. Conclusions: These results suggest that wearing soft contact lens in dry eyes differently affect tear film compared to normal eyes. Thus, dry eyes need more advertent fitting for contact lens wearing because of unstable tear film.

• Journal of Korean Ophthalmic Optics Society
• /
• v.5 no.2
• /
• pp.91-98
• /
• 2000

To investigate the distribution of dry eye and to accept diagnosis methods of dry eye in ophthalmic shop, this study was performed on 81 persons(male : 49, female : 32). 1. We divided two group for diagnosing dry eye by dry eye screening questionnaire : one was dry eye symptom group(49.3%) and the other was non-dry eye symptom group(50.7%). 2. Non-invasive break-up time(NIBUT) which was measured by using Tear $scope^{(R)}$ (Killer. co)was longer than invasive break-up time(IBUT). 3. A blink rate in dry eye symptom group(10%) was measured lesser than 10 cycle/min, in non-dry eye symptom group(14.9%). 4. In shirmer test there were lesser than 10mm/5min in dry eye symptom group(67.5%), in non-dry eye symptom group(39%). 5. Cornea and conjunctival staining by rose bengal represented Mild 25%, medium 36.25%, extreme 38.75% in dry eye symptom group. Non-dry eye symptom group was showed Mild 19.51%, medium 14.63%, extreme 12.19%. 6. These results showed that the patient showed dry eye symptom in 3 items of eye examination was 22.5%, 4 items 25%, 5 items 30%, 6 items 15%.

• Korean Journal of Materials Research
• /
• v.3 no.6
• /
• pp.606-613
• /
• 1993

This was studied about aging characteristic of AC4A/$SiC_{w}$ 10-30v/o reinforced composite. Aging hardenability was decreased $SiC_{w}$ 30% > 10% > 20%. Aging hardening of T6 treatmented composite was higher absolute value than AC4A I/M material. And this results indicated initial hardening phenomenon according to increase $SiC_{w}$ volume fraction. Reinforced effect by pressure was the same effect as before aging treatment and the best condition pressure at 75MPa. Similar to reinforced effect according to $SiC_{w}$ volume fraction was 30 % > 10 % > 20 %. In case of pressure is low, whisker is not break the same time press with base metal after wetting. After it is wetting with base metal, a part transformed or wetting part break and whisker maintain original shape or a part transformed on the otherhand, in case of pressure is high, whisker is break in same time it was not against pressure and whisker's shape is near a polygon or spherical shape.