• Journal of Energy Engineering
• /
• v.6 no.2
• /
• pp.162-169
• /
• 1997

The particle size effect on the combustion characteristics of pulverized coal was investigated in the cylindrical-shape, horizontal furnace, fired in the range of 8.8∼10.6 kw. Three differently-sized fractions (5, 30, and 44 microns in average diameter) of high-volatile bituminous coal, were burned in the test furnace. Burnout behavior of pulverized coal flame were determined through the measurement of stable species concentrations (CO$_2$and H$_2$O). Concentrations of CO$_2$were compared with the theoretical values and the result showed good agreement. Thermal behavior of pulverized coal flame were determined as maximum flame temperatures occurred at fuel-rich conditions in every case. Flame lengths were also determined by decreasing with the particle size decrease. The flame length of the fine sized coal sample was comparable to that produced by distillate oil. The color of the coal flames ranged from orange to yellow, with the flame of the fine size fraction being brighter and yellower than the others.

• Journal of environmental and Sanitary engineering
• /
• v.14 no.4
• /
• pp.93-98
• /
• 1999

We had investigated combustion properties of rice bran dusts. Decomposition of rice bran dusts with temperature were investigated using DSC and the weight loss according to temperature using TGA in order to find the thermal hazard of rice bran dusts, and the properties of dust explosion in variation of their dust with the same particle size. Using Hartman's dust explosion apparatus which estimate dust explosion by electric ignition after making dust disperse by compressed air, dust explosion experiments have been conducted by varying concentration and size of rice bran dust.According to the results for thermodynamic stability of rice bran dust, there are little change of initiation temperature of heat generation and heating value for used particle size. But initiation temperature of heat generation decreased with high heating rate whereas decomposition heat increased with particle size. Average maximum explosion pressure was $10kgf/cm^2$ for 60/70 mesh and $1.5mg/cm^2$ dust concentration.

• Journal of the Korean Ceramic Society
• /
• v.23 no.4
• /
• pp.11-16
• /
• 1986

$BaTiO_3$ ceramics powder was prepared by coprecipitation method either in oxalic acid solution or in potassium hydroxide solution. Thermal decomposition of coprecipitated $BaTiO(C_2O_4)_2$.$4H_2O$ powder in oxalic acid solution was investigated by means of Themogravimetry Differential Thermal Analysis and X-ray Diffraction Analysis. Low temperature decomposition of coprecipitated $BaTiO(C_2O_4)_2$.$4H_2O$ caused narrow particle size distribution whereas high temperature decomposition caused fairly wide particle size distribution by partial sintering. As the reaction time increased the average particle size of coprecipitated $BaTiO_3$ powder in KOH solution was increased. The most narrow paticle size distribution was obtained when the coprecipi-tates were ripened for 4hrs.

• Journal of Powder Materials
• /
• v.13 no.6 s.59
• /
• pp.421-426
• /
• 2006

The microstructural and mechanical properties of Al-Si alloyed powder, prepared by gas atomization fallowed by hot extrusion, were studied by optical and scanning electron microscopies, hardness and wear testing. The gas atomized Al-Si alloy powder exhibited uniformly dispersed Si particles with particle size ranging from 5 to $8{\mu}m$. The hot extruded Al-Si alloy shows the average Si particle size of less than $1{\mu}m$. After heat-treatment, the average particle size was increased from 2 to $5{\mu}m$. Also, mechanical properties of extruded Al-Si alloy powder were analyzed before and after heat-treatment. As expected from the microstructural analysis, the heat-treated samples resulted in a decrease in the hardness and wear resistance due to Si particle growth. The friction coefficient of heat-treated Al-Si alloyed powder showed higher value tough all sliding speed. This behavior would be due to abrasive wear mechanism. As sliding speed increases, friction coefficient and depth and width of wear track increase. No significant changes occurred in the wear track shape with increased sliding speed.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.26 no.3
• /
• pp.278-284
• /
• 2017

Generally, classifiers have been used as machines to crush raw materials and classify suitable particle sizes in all industrial fields, such as food, chemical, and mineral. However, the technique for classifying micron-sized particles between 5 and $20{\mu}m$ is inferior. In particular, numerous experiments and considerable experiences are required to predict the particle size, because the classifier particle size is determined according to the internal flow. However, it is quite difficult to set the driving conditions so that the desired particle size can be classified only by experience and experimentation. Therefore, this study proposes a method of predicting the average particle size by employing multiphase flow analysis and the Taguchi method; this method is subsequently verified.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.216-219
• /
• 2004

Due to the recent amazing achievements in nano technology. preparation of cement nano particles by mechanical method are examined to improve their properties. The experimental results show that the particle size after 3 hr milling were about 500nm. The SEM photographs of specimens also reveal that average sizes of cement particles are gradually decreased by milling time. And in the TG/DSC, influence of the alcohol is showed strongly. The value of TG of the crushed cement was larger than that of the non-crushed cement. That is also judged to be cause the alcohol.

• Journal of Magnetics
• /
• v.16 no.4
• /
• pp.368-373
• /
• 2011

Particle size distributions in 10 nm magnetite ferrofluids are analyzed based on both dc and ac magnetic measurements. Modified log-normal distributions are used for fitting the experimental results, which allows for a proper account of the narrow distributions. The calculated average particle sizes are in good agreement with the TEM results. However the ac method gives a much narrower distribution width than that of the dc magnetization curve fit. The proposed measurements combined with the analysis methods are useful for the characterization of ferrofluids being considered for biomedical applications.

• Journal of Powder Materials
• /
• v.26 no.3
• /
• pp.201-207
• /
• 2019

Tungsten heavy alloys (W-Ni-Fe) play an important role in various industries because of their excellent mechanical properties, such as the excellent hardness of tungsten, low thermal expansion, corrosion resistance of nickel, and ductility of iron. In tungsten heavy alloys, tungsten nanoparticles allow the relatively low-temperature molding of high-melting-point tungsten and can improve densification. In this study, to improve the densification of tungsten heavy alloy, nanoparticles are manufactured by ultrasonic milling of metal oxide. The physical properties of the metal oxide and the solvent viscosity are selected as the main parameters. When the density is low and the Mohs hardness is high, the particle size distribution is relatively high. When the density is high and the Mohs hardness is low, the particle size distribution is relatively low. Additionally, the average particle size tends to decrease with increasing viscosity. Metal oxides prepared by ultrasonic milling in high-viscosity solvent show an average particle size of less than 300 nm based on the dynamic light scattering and scanning electron microscopy analysis. The effects of the physical properties of the metal oxide and the solvent viscosity on the pulverization are analyzed experimentally.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.4
• /
• pp.563-566
• /
• 1998

$BaTiO_3$ fine particles were prepared by hydrothermal process from titanium tetra-isoproproxide ($Ti(OiPr)_4$) and barium hexa-hydroxide ($Ba(OH)_2{cdot}8H_2O$) as raw materials. The fine particles were obtained at the temperature range of 160 to $185^{\circ}C$. The properties of $BaTiO_3$ particles were studied as a function of various parameters such as reaction temperature, reaction time and Ba/Ti ratio, etc. The average particle size of $BaTiO_3$ increased with increasing reaction temperature and time. After hydrothermal treatment at $170^{\circ}C$ for 8 h, the average particle size of $BaTiO_3$ was about 30 nm and the particle size distribution was narrow.

• Journal of Powder Materials
• /
• v.14 no.1 s.60
• /
• pp.63-69
• /
• 2007

The present study was focused on the synthesis of a zirconium-based alloyed nanopowder by the plasma arc discharge process. The chemical composition, phase structure, particle size and hydrogen sorption property of the synthesized powders under various synthesis conditions were analyzed using XRF, XRD, SEM, XPS and the ASTM-F798 method. The chemical composition of the synthesized Zr-V-Fe-based powders approached that of the raw material with an increasing hydrogen fraction in the powder synthesis atmosphere. The synthesized $Zr_{55}V_{29}Fe_{16}$ powder consist of a mixed phase structure of the $Zr,\;ZrH_2,\;FeV\;and\;Zr(V_{1-x}Fe_{x})_2$ phases. This powder has an average particle size of about 20 nm. The synthesized $Zr_{55}V_{29}Fe_{16}$ nanopowder showed getter characteristics, even though it had a lower hydrogen sorption speed than the $Zr_{57}\;V{36}\;Fe_7$ getter powder. However, the synthesized Zr nanopowder with an average particle size of 20 nm showed higher hydrogen sorption speed than the $Zr_{57}\;V{36}\;Fe_7$ getter powder.