• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.4
• /
• pp.569-579
• /
• 1994

A 5.9kW phosphoric acid fuel cell(PAFC) power generation system that consists of a reformer, a stack, heat exchangers, an automatic data acquisition and control system was designed, fabricated and analyzed. This system which was firstly fabricated in Korea has been operated for 140 hours with an electricity generation of 684kWh. The PAFC generate electricity in the range of 38-52V and 50-160A and has a typical I-V characteristics of a fuel cell. Using the reformed fuel, the system performance is decreased in some degree due to CO content, compared to using the simulated fuel. At steady state operation condition, the total efficency of this system was 45.2%.

• Journal of Institute of Control, Robotics and Systems
• /
• v.7 no.4
• /
• pp.334-343
• /
• 2001

Polishing a die that has free-form surfaces is a time-consuming and tedious job, and requires a considerable amount of high-precision skill. Some workers tend to gradually avoid the polishing work because of the poor environment caused by dust and noise. In order to reduce the polishing time and cope with the shortage of skilled workers, a user-friendly automatic polishing system was developed in this research. The polishing system with five degrees of freedom is able to keep the polishing tool normal to the die surface. The polishing system is controlled by a PC-NC controller. To easily operate the developed polishing robot system, this study developed an integrated program in the Windows environment. This program consists of four modules: the polishing module, the graphic simulator, the polishing data generation module, and the teaching module. Also, the automatic teaching system was developed to easily obtain teaching data and it consists of a three dimensional joystick and a proximity sensor. The joystick is used to simultaneously drive the polishing system to an arbitrary orientation and the proximity sensor is used to obtain teaching points precisely. Also, to evaluate the stability of the driving program and the teaching system, polishing experiments of a die of saddle shape were carried out.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.2
• /
• pp.327-334
• /
• 2020

In this paper, an automatic cruise system of unmanned boat was developed for surveying water depth in reservoir using accurate location information. Using global satellite navigation system(GNSS) data in real time, this unmanned system, combined with an echo sounder, can simultaneously collect location information and depth information on the reservoir. This automatic navigation system allows the automatic route generation program to automatically generate a cruise route according to the input conditions for grid sizes of 5m, 10m and 20m, and automatically controls the cruise route with high positional accuracy. The developed system was tested to verify the applicability of the selected Yonggok(Geoncheon) reservoir as a test reservoir located in Suncheon, Jeollanam-do.

• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.6
• /
• pp.920-927
• /
• 1998

This paper presents a synthetic control algorithm that generates the rudder command angle to track the optimal route which is composed of straight-lines among way-points with keeping a required error limit. The control algorithm comprises three main lgorithms that is a course-keeping algorithm that eliminates the yaw angle difference between optimal route and current route a track-keeping algorithm that tracks the optimal route among way-points and a turning-control algorithm that includes the generation of optimal turning routes and control method. The effectiveness of the proposed control algorithm is assured through computer simulation.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.11
• /
• pp.1104-1111
• /
• 2009

In the low altitude, mission of the aircraft is restricted by a variety of threats such as anti-air missiles and terrain obstacles. Especially, aircraft have always a risk of ground collision near terrain. In this study, to effectively solve this problem, we developed the flight path generation algorithm that is considered the terrain avoidance. In this flight path generation algorithm, waypoints that should be passed by the UAV are selected first. The waypoints are located in the middle of the terrain obstacles. Then, physically meaningful waypoints sets are classified by Dijkstra algorithm. The optimal waypoint guidance law based on the optimal control theory is applied to produce trajectory candidates. And finally the minimum control energy trajectory is determined.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.1
• /
• pp.81-88
• /
• 2007

In this paper, a new single-phase utility-interactive inverter system for residential power generation with fuel cell is proposed. The proposed inverter system is not only capable of working in both stand-alone and grid-connected mode, but also ensures smooth and automatic transfer between the two modes of operation. The proposed control method has little steady-state error and good transient response characteristic. Also, the control method can be implemented using low-cost, fixed point DSP since it has simpler structure, smaller amount of calculation, and smaller number of sensors. The controller for the proposed utility-interactive inverter system is described, and the validity is verified through simulation and experiment.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.5
• /
• pp.3044-3050
• /
• 2015

The purpose of this study is to analyze the performance of the flow control oil pump for automatic transmission. The numerical model for analysis the performance of the flow control oil pump was develop and the characteristics of the internal flow, discharge flow rate, displacement of outer ring, driving torque, generation of cavitation was investigated according to rotating speed. As a result, the cavitation generation increased as the rotating speed increased. The volumetric efficiency was 90% for 2200 rpm and it decreased rapidly, then it decreased about 81% for 5000 rpm. Besides, the cavitation generation was 20%~30% for inlet of suction part, but it reduced below 13% owing to the compression. However, it shows higher cavitation generation for high rotating speed like 5000 rpm.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.910-917
• /
• 2011

CBTC(Communication Based Train Control) car-borne equipment, a part of the communication based train control system, mainly consists of automatic train protection(ATP) functions, automatic train operation(ATO) functions as well as the interface functions with other equipment including CBTC wayside equipment and train control management system etc. The CBTC car-borne software implementing ATP/ATO functions is a real-time embedded software requiring a high level of safety and reliability. To satisfy the requirements of the CBTC car-borne software, the model-based design techniques are applied with SCADE(Safety-Critical Application Development Environment) to the development of the CBTC car-borne software. In this paper, we illustrate the process modeling the car-borne ATP/ATO functions satisfying system requirement specification with system requirement management, modeling and document generation tools etc. supported by SCADE. In addition, the developed models corresponding to the ATP/ATO functions are applied to the train with CBTC car-borne equipment through its corresponding EN-50128 standards-compliant C code generated by the code generator. It is shown from the test result that the ATP/ATO models developed by SCADE work well while the trains are running in driverless operation mode.

• International Journal of Automotive Technology
• /
• v.6 no.2
• /
• pp.107-117
• /
• 2005

A distributed hardware-in-the-loop simulation (HILS) platform is developed for designing an automotive engine control system. The HILS equipment consists of a widely used PC and commercial-off-the-shelf (COTS) I/O boards instead of a powerful computing system and custom-made I/O boards. The distributed structure of the HILS system supplements the lack of computing power. These features make the HILS equipment more cost-effective and flexible. The HILS uses an automatic code generation extension, REAL-TIME WORKSHOP$^{ (RTW$^{) of MATLAB$^{ tool-chain and RT-LAB$^{, which enables distributed simulation as well as the detection and generation of digital event between simulation time steps. The mean value engine model, which is used in control design phase, is imported into this HILS. The engine model is supplemented with some I/O subsystems and I/O boards to interface actual input and output signals in real-time. The I/O subsystems are designed to imitate real sensor signals with high fidelity as well as to convert the raw data of the I/O boards to the appropriate forms for proper interfaces. A lot of attention is paid to the generation of a precise crank/ earn signal which has the problem of quantization in a conventional fixed time step simulation. The detection of injection! command signal which occurs between simulation time steps are also successfully compensated. In order to prove the feasibility of the proposed environment, a simple PI controller for an air-to-fuel ratio (AFR) control is used. The proposed HILS environment and I/O systems are shown to be an efficient tool to develop various control functions and to validate the software and hardware of the engine control system.

• Proceedings of the KIEE Conference
• /
• 1999.07b
• /
• pp.734-736
• /
• 1999

The electricity demand has been in the trend of increase for the past 30 years except last year due to economic crisis. The central electrical power dispatch center anticipates each and every hour's electricity demand and dispatch every power plant's output(MW) taking into account of the costs, frequency regulation abilities, locations, reliabilities and so on. to meet the demand as quickly as possible. The large portion of the power plants' output is contolled automatically by the AGC(Automatic Generation Control) function which is a part of the EMS(Energy Manage System) computer in the dispatch center. To receive the electrical power dispatch signal from the EMS, a power plant should have a remote MW control feature in the turbine control system or unit master control system. We investigated the AGC function and a power plant's remote MW control configuration.