In this work, the electrical and optical properties of the two different p-type GaN electrode schemes, ZnNi/ITO and ZnNi/Au, were compared each other, and applied to the top-emitting GaN/InGaN light-emitting diodes (LEDs). The ZnNi/ITO electrode showed much higher transmittance (90%) and slightly lower contact resistance $(1.27{\times}10^{-4}{\Omega}cm^2)$ than those (77%, $(2.26{\times}10^{-4}{\Omega}cm^2)$) of the ZnNi/Au at a wavelength of 460 nm. In addition, GaN LEDs having ZnNi/ITO showed accordingly higher light output power and luminous intensity than those having ZnNI/Au did at the current levels up to 1 A.
The Al:Au double-layer metal electrode for use in transparent, dual emission of organic light-emitting diode (OLED) was fabricated. The electrode of Al:Au metals with various thicknesses was deposited by the vacuum thermal evaporation technique. For Al thickness of 1 nm, a bottom luminance of $4880\;cd/m^2$ was observed at 8 V. Otherwise, top luminance of $2020\;cd/m^2$ were observed at 8 V. In addition, the threshold voltages of the electrodes were 2.2 V. It was forward that the inserting 1 nm Al between LiF and Au enhanced electron injection with tunneling effect.
We investigated the effects of power ratio on the electrical and optical properties of Au based Ga-, B- codoped ZnO(GZOB) thin films. GZOB thin films were deposited on Au based poly carbonate(PC) substrate with various power in the range from 60 to 120 W by DC magnetron sputtering. In the result, GZOB films at 100 W exhibited a low resistivity value of $1.12\times10^{-3}\Omega-cm$, and a visible transmission of 80 % with a thickness of 300 nm. This result indicated that the addition of Ga and B in ZnO films leads to the improvement of conductivity and transparent. From the result, we can confirm the possibility of the application as transparent conductive electrodes.
We report on the development of a new method to control the coverage of a metal film prepared with immersion method. An Sb species in solution adsorbed irreversibly at an open circuit potential (∼0.2 V) as an oxygenous Sb(Ⅲ) on a clean Au electrode, and the adsorbates showed voltammetric features in the potential range from 0.1 V to - 0.4 V. The full coverage of the Sb adsorbates was ∼0.45. On the contrary, the Sb species in solution did not adsorb at all on iodine-covered Au electrode surfaces, when the iodine coverages were more than 0.25. As the iodine coverage decreased below 0.25, however, the irreversible adsorption of Sb took place and the coverage of Sb increased accordingly. This electrochemical behavior has been interpreted as the penetration of the adsorbing Sb species in solution through open spaces among the iodine adlattices of coverages less than 0.25. With the manipulation of the iodine coverage, the controllable range of Sb coverage was from 0 to 0.45, i.e. the full coverage of Sb. In addition, the reversible deposition of Sb on an iodine-saturated Au electrode with voltammetric scan has been observed, which is contrasted with the adsorptive behavior of Sb on the clean Au electrode.
Porous dendrite structure AuCu alloy was formed using a hydrogen bubble template (HBT) technique by electroplating to improve the catalytic performance of gold, known as an excellent oxygen reduction reaction (ORR) catalyst in alkaline medium. The rich Au surface was maximized by selectively electrochemical etching Cu on the AuCu dendrite surface well formed in a leaf shape. The catalytic activity is mainly due to the synergistic effect of Au and Cu existing on the surface and inside of the particle. Au helps desorption of OH- and Cu contributes to the activation of O2 molecule. Therefore, the porous AuCu dendrite alloy catalyst showed markedly improved catalytic activity compared to the monometallic system. The porous structure AuCu formed by the hydrogen bubble template was able to control the size of the pores according to the formation time and applied current. In addition, the Au-rich surface area increased by selectively removing Cu through electrochemical etching was measured using an electrochemical calculation method (ECSA). The results of this study suggest that the alloying of porous AuCu dendrites and selective Cu dissolution treatment induces an internal alloying effect and a large specific surface area to improve catalyst performance.
In this study, the Au/Ni and Au/Ni/Si/Ni layers prepared by electron beam evaporation were used to form ohmic contacts on p-type GaN. Before rapid thermal annealing, the current-voltage(I-V) characteristic of Au/Ni and Au/Ni/Si/Ni contact on p-type GaN film shows non-ohmic behavior. A Specific contact resistance as 3.4$\times$10$^{-4}$ Ω-$\textrm{cm}^2$ was obtained after 45$0^{\circ}C$-RTA. The Schottky barrier height reduction may be attributed to the presence of Ga-Ni and Ga-Au compounds, such as Ga$_4$Ni$_3$, Ga$_4$Ni$_3$, and GaAu$_2$ at the metal - semiconductor interface. The mixing behaviors of both Ni and Au have been studied by using X-ray photoelectron spectroscopy. In addition, X-ray diffraction measurements indicate that the Ni$_3$N, NiGa$_4$, Ni$_2$Si, and Ni$_3$Si$_2$ Compounds were formed at the metal-semiconductor interface.
We present the structural and optical properties of Au@TiO2 core-shell microsphere structure prepared by a hydrothermal synthesis method. As a way to improve the efficiency of organic solar cells, the Au@TiO2 core-shell microsphere was synthesized to use the local surface plasmon resonance (LSPR) phenomenon. The synthesized results were confirmed to have the Au@TiO2 core-shell structure using a high-resolution transmission electron microscopy. An absorption was observed to occur at 527 nm belonging to the visible light region using a visible light spectroscopy, which supports the LSPR phenomenon. We suggest that the Au@TiO2 core-shell microsphere is highly likely to be applied to organic solar cells including dye-sensitized solar cells. In addition, we expect it to be widely used not only in the energy but also in the bio as well as in the environmental fields.
본 연구에서는 COG (Chip On Glass) 패키지 적용을 위해 Au 범프를 전기도금 공정을 사용하여 Al/Si wafer와 SiN/Si wafer 위에 TiW/Au 구조를 갖는 두 종류의 Au범프 시료를 제작하였다. UBM (Under Bump Metallurgy) 물질로서 TiW 박막을 스퍼터링 방법으로 증착하였으며 스퍼터링 입력 파워(500~5000 Watt)에 따른 박리 현상을 관찰하였다. 안정된 계면 접착을 나타내는 스퍼터링 파워는 1500 Watt임을 확인 할 수 있었다. 또한 SAICAS (Surface And Interfacial Cutting Analysis System) 장비를 사용하여 기판 종류에 따른 Au Bump의 접착력을 조사하였다. TiW 증착 조건은 스퍼터링 파워를 1500 Watt로 고정하였다. TiW/Au 계면의 접착력은 두 종류의 wafer (Al/Si과 SiN/Si wafers)에 관계없이 오차 범위 안에서 비슷한 접착력을 보여주었으나, TiW UBM 스퍼터링 박막 계면에서의 접착력은 하부 박막인 Al 금속과 SiN 비금속 박막에서의 접착력 차이가 약 2.2배 크게 나타났다. 즉, Al/Si wafer와 SiN/Si wafer위에 증착된 TiW의 접착력은 각각 0.475 kN/m와 0.093 kN/m 값을 나타내었다.
본 연구에서는 저품위인 35wt% 금합금에 대해 80.0wt% 이상의 Au를 얻기 위한 건식 정련 공정을 제안하였다. Au35wt%-Ag5wt%-Cu60wt%의 조성을 가진 금합금에 대해 PbO/(PbO+CaO)의 혼합비를 각각 0~1로 변화시키고 플럭스/금합금의 무게비는 1/2로 하여 $1200^{\circ}C$-5시간의 열처리를 진행하였다. 이때 공정 전, 후 시료의 조성 변화는 energy dispersive X-ray spectroscopy(EDS)로 확인하고, 공정이 완료된 후 분리된 플럭스 금속 원소 성분은 time of flight secondary ion mass spectromerty(ToF-SIMS)로 확인하였다. EDS분석 결과 플럭스의 비율이 1(PbO 단일)인 경우 Au의 함량이 35.0wt%에서 86.7wt%로 가장 크게 향상되었고, 다른 플럭스 조성의 경우도 84wt% 이상으로 정련이 가능하였다. 또한 2/3 혼합비의 플럭스에서 Ag가 플럭스부로 빠져나가는 손실이 가장 적었다. 플럭스부의 ToF-SIMS 분석 결과 플럭스의 비율이 1, 0 일 때 $Au^+$의 특성 피크의 강도가 각각 349, 37로 측정되었다. Au의 손실을 고려하였을 때 CaO 단일 플럭스의 사용이 더 유리할 수 있었으나, 이 정도의 신호강도는 무시할 수 있는 정도로 판단되었다. 따라서 혼합플럭스를 이용한 건식 열처리를 통해 효과적인 금의 정련이 가능하여 경제적인 습식제련의 전처리 공정으로 사용될 수 있음을 확인하였다.
The crorosion film of gilt bronz, silver and iron objects, which were excaved from Ancient Tomb of Silla Dynasty, was removed by the electrolytic reduction process. These metallic objects were mainly investigated for microstructure, designs and gilting film etc. Most iron objects might be made by hot forging process. The cold extrusion technique might be used for gold and silver objects, in addition to an amalgam method might be applied for the gilting Au film on Cu-alloy surface. For the gilting on glass surface, first, a Cu alloy was cladded on glass , next, Au-film was obtained on the Cu-ally by the amagum method.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.