• Journal of Korean Ophthalmic Optics Society
• /
• v.12 no.4
• /
• pp.19-22
• /
• 2007

Recently, the population of people exploring High Mountain trekking or expedition is increasing as an increase in the backpackers. Many accidents occurring at High Mountain above 6,000 m are the results of snow blindness. The damage of cornea and/or retina is direct cause of snow blindness. The UV intensity increases on the hand, along with the altitude caused by decrease in the atmospheric pressure, on the other hand the reflections by bright snow at high mountain area. And it increases approximately 3 times and 4 times higher than the ground level at altitude of 4,000 m and 8,000 m, respectively. The use of sunglasses is more favorable than goggles for the protection of snow blindness at High Mountains. The eye frames that have high mechanical strength and the plastic lenses which can protect UV 100% are recommended. The attachable shielding pads are needed to prevent the incident UV light reflected or scattered from the gap between glasses frame and face. The sunglasses must have flexible and long temples to wind the ears adequately for the prevention of detachment during climbing and it is recommended that the metal frame to be coated with plastics to prevent the eye surroundings from frostbite.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.21 no.4
• /
• pp.127-137
• /
• 2019

Nail art, which has been popularized recently, has increased convenience in the direction of nail art design harmonized with clothing and the increased interest and usage of nail art decoration. This study set out to propose practical planar and three-dimensional nail art designs in harmony with modern clothes by applying trimmings common in 18th century women's clothing, which used a variety of attachable decorations. As for the methodology, the investigator examined theories in previous studies, literature, and analyzed the types of trimming in female portraits from the 18th century at the museum at the Palace of Versailles in France. Planar and three-dimensional nail art designs were created for each of the top three trimming types- braids, laces, and ribbons, which were identified through analysis. The study applied the trimmings of the 18th century women's clothes to nail art design and had the following results: First, the top three trimming types were identified based on the analysis of the 18th century portraits. They were then used as motifs in the production of planar and three-dimensional nail art designs. The results show that the motifs of the clothes trimmings were fit for and had practical possibilities for expression in nail art designs. Secondly, diversity and the expansion of ideas in the study of nail art design were promoted. In addition, elements were increased to have mutually complementary effects with clothes. Finally, the study made various attempts at nail design methods by adopting a range of nail art expression techniques including hand painting, 2D & 3D art techniques, and using planar and three-dimensional nail decorations, thus proposing a positive direction for the organization of a curriculum to make use of 18th century women's clothing motifs in nail art education.

• Journal of Biosystems Engineering
• /
• v.36 no.1
• /
• pp.9-14
• /
• 2011

This study was carried out to develop a vine crusher for harvesting sweet potato. The experimental two-row vine crusher attachable to agricultural tractor composed of vine crushing part with frail type vine crushing blades and vine lifting blades, power transmission part with chain and gear transmission mechanism, crushing height control part with two control wheels and manual levers, and implement frames, was designed and fabricated. And this vine crushing performance was also analyzed. From vine crushing tests, backward travel direction (i.e., rotational direction of the vine crushing blades) showed better vine crushing performance than forward travel direction. Crushing ratio of remained vine was increased, and length of remained vine and length of crushed vine were decreased as working speed was decreased and rotational speed of vine crushing blades was increased. At a working speed of 0.27 m/s and rotational speed of vine crushing blades of 800 rpm, crushing ratio of remained vine was 98%, length of remained vine was 104 mm, and length of crushed vine was 327 mm. But, when crushing vine on irregular ridges, vines and mulching vinyl were wound in the vine crushing part. Therefore, change of location of power transmission chain mechanism, and an automatic control device for controlling crushing height were needed.

• Journal of the Korean Society of Visualization
• /
• v.7 no.2
• /
• pp.17-21
• /
• 2010

This paper presents the fabrication and performance measurement of a temperature sensor array on a flexible substrate attachable to a curved surface using MEMS technology. Specifically, the fabrication uses the well-developed printed circuit board fabrication technology for complex electrode definition. The temperature sensor array are lifted off with a $10{\times}10$ matrix in a $50\;mm{\times}50\;mm$ to visualize temperature distribution. Copper is used as temperature sensing material to measure the change in resistances with temperature increase. In a thermal oven with temperature control, the temperature sensor array is Characterized. The constant slope of resistance change is obtained and temperature distribution is measured from the relationship between resistance and temperature.

• Journal of Adhesion and Interface
• /
• v.5 no.2
• /
• pp.22-36
• /
• 2004

Several in-situ testing methods of adhesively bonded joints under static short-time tensile loading are critically analyzed in terms of experimental procedure and data evaluation. Due to its rather homogeneous stress state across the glue line, the tensile-shear test with thick single-lap specimens, according to ISO 11003-2, has become the most important test process for the determination of realistic materials parameters. This basic method, which was improved in both, the experimental part by stepped adherends and easily attachable extensometers and the evaluation procedure by numeric substrate deformation correction and test simulation based on the finite element method (FEM), is therefore demonstrated by application to several kinds of adhesives and metallic adherends. Multi-axial load decreases the strength of a joint. This effect, which is illustrated by an experimental comparison, impedes the derivation of realistic mechanical characteristics from measured force-displacement curves. It is shown by numeric modeling that tensile-shear tests with thin plate substrates according to ISO 4587, which are widely used for quick industrial quality assurance, reveal an inhomogeneous stress state, especially because of relatively large adherend deformation. Complete experimental determination of the elastic properties of bonded joints requires independent measurement of at least two characteristics. As the thick-adherend tensile-shear test directly yields the shear modulus, the tensile butt-joint test according to ISO 6922 represents the most obvious complement of the test programme. Thus, validity of analytical correction formulae proposed in literature for the derivation of realistic materials characteristics is verified by numeric simulation. Moreover, the influence of the substrate deformation is examined and a FEM correction method introduced.

• Journal of the Korean Society of Costume
• /
• v.57 no.8
• /
• pp.14-23
• /
• 2007

The purpose of this study was to investigate the present condition of cold protective clothing for mailman, to improve its design in movement, fitness, and other functions, and supply basic data for its performance evaluation. The results are as follows : The 46.60% of those questioned did not satisfy current clod protective clothing fer mailman. Especially, they considered dissatisfactory in properties such as waterproof, comfort, activity, and sweat absorption. The newly developed cold protective clothing is two-piece style composed of jacket and pants. Both jacket and pants are composed of inner and outer clothing individually. In both jacket and pants, their outer clothing's material was waterproof, windproof, and breathable shell fabric on which PTFE film laminated and their inner clothing's material was 100% polyester Polar polis to have better insulation property. The jacket has attachable cap which can be used as rain gear and set-in sleeve with stand collar. It also had big outside patch pockets and side seam pockets to ensure enough storage space. The pants have knee pads to give free movement to knees and slant side pockets. Inner clothing of both jacket and pants can be worn during working inside without out clothing. Insulation of the newly developed cold protective clothing was not better than current one except right hand, left hand and left foo. It is considered that is because thickness of material is the most important factor to influence insulation.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.6
• /
• pp.157-163
• /
• 2018

This study is aimed at controlling the fiber orientation and improve the fiber distribution in fiber-reinforced cement composites using blades that can be placed inside the existing nozzles. To optimize the blade parameters, multi-physics finite element analysis was performed that could account for the flow of the cementitious matrix material, the movement of the entrained fibers, and the interactions with the nozzle. As a result, this study defined the blade distance, length, and position as a function of the fiber length to be used in the field. The blades with a distance from 1.2 to 2.4 times the fiber length and length from 4 to 8 times the fiber length, as well as located at below 14 times the fzfiber length from the nozzle exit maintained the fiber orientation angle less than $5^{\circ}$. In addition, the blade-type nozzle proposed in the study can be attachable and detachable to the conventional casting equipment, and thus it can provide the usability and convenience in practical applications.

• Journal of Biosystems Engineering
• /
• v.34 no.2
• /
• pp.114-119
• /
• 2009

Field test was conducted to investigate primary factors reducing rapeseed harvesting using a reciprocating cutter-bar of combine. The results showed that the correlation between crop moisture content and yield loss had a U-type, which indicated that the yield reduction increased at too high and too low crop moisture contents. The proper ranges of crop moisture contents were 27${\sim}$35%, 21${\sim}$56%, and 62${\sim}$73% in case of grain, pod and stem, respectively. Crop moisture content was negatively correlated with header loss, but positively correlated with threshing loss. In contrary, stem moisture content showed positive correlations with total loss, threshing loss and separation loss. Working speed was positively correlated with header loss. Total flow rate, pod flow rate and stem flow rate were highly correlated with threshing loss and separation loss. However, grain flow rate did not show any correlation with total loss. According to the principal component analysis, two principal components were derived as components with eigenvalues greater than 1.0. The contribution rates of the first and the second components were 52.7% and 38.9%, which accounted for 91.6% of total variance. As a contributive factor influencing total loss of rapeseed mechanical harvesting, a crop moisture content factor was greater than a crop flow rate factor. The stepwise multiple regression analysis for total loss was conducted using crop moisture content factor, crop flow rate factor and coefficient. However, the model did not show any correlation among independent and dependent factors ($R^2$=0.060).

• Journal of Advanced Navigation Technology
• /
• v.17 no.6
• /
• pp.712-719
• /
• 2013

This paper studies the security module for the reliable transmission of the meter reading and the control data between the remote terminals and the upper server-side in smart water grid. The proposed security module was implemented to make it attachable to the remote terminal without security function. In particular, unlike the smart grid of electric field, the low power is considered due to the use of battery power in the smart water grid, and the ARIA-GCM-128 symmetric key method is adopted taking into the account that the damp and constrictive environments by the installed meter location in the underground occur a communication obstacle on building of the large-scale network system. The encryption module of this paper was devised to ensure the safety between the reading data on the terminal and the control data from the upper server, and secure the stability of the remote meter reading system by taking protection against an arbitrary alteration or modification.

• Polymer(Korea)
• /
• v.36 no.1
• /
• pp.88-92
• /
• 2012

Long-term performance of polymer under constant sustained load has been the main research focus, which created a need for the accelerated test method providing proper lifetime assessment. Cycling fatigue loading is one of the accelerated test method and has been of great interest. Microstructure change of high density polyethylene under cyclic fatigue loading and creep was examined utilizing a tensile device specially designed for creep and fatigue test and also can be attachable to the X-ray diffractometer. In this way, the crystal morphology change of polyethylene under creep and cyclic fatigue load was successfully monitored and compared. Despite the marked differences in macroscopic deformation between the creep and cyclic fatigue tests, crystal morphology such as crystallinity, crystal size, and $d$-spacing was as nearly identical between the two test cases. Specimens pre-deformed to different strains, i.e., before yield point (BYP), at yield point (YP) and after yield point (AYP), however, showed markedly different changes in crystal morphology, especially between AYP and the other two specimens.