• 한국재료학회지
• /
• 제29권8호
• /
• pp.463-468
• /
• 2019

The electrical and interfacial properties of $HfO_2/Al_2O_3$ and $Al_2O_3/HfO_2$ dielectrics on AlN/p-Ge interface prepared by thermal atomic layer deposition are investigated by capacitance-voltage(C-V) and current-voltage(I-V) measurements. In the C-V measurements, humps related to mid-gap states are observed when the ac frequency is below 100 kHz, revealing lower mid-gap states for the $HfO_2/Al_2O_3$ sample. Higher frequency dispersion in the inversion region is observed for the $Al_2O_3/HfO_2$ sample, indicating the presence of slow interface states A higher interface trap density calculated from the high-low frequency method is observed for the $Al_2O_3/HfO_2$ sample. The parallel conductance method, applied to the accumulation region, shows border traps at 0.3~0.32 eV for the $Al_2O_3/HfO_2$ sample, which are not observed for the $Al_2O_3/HfO_2$ sample. I-V measurements show a reduction of leakage current of about three orders of magnitude for the $HfO_2/Al_2O_3$ sample. Using the Fowler-Nordheim emission, the barrier height is calculated and found to be about 1.08 eV for the $HfO_2/Al_2O_3$ sample. Based on these results, it is suggested that $HfO_2/Al_2O_3$ is a better dielectric stack than $Al_2O_3/HfO_2$ on AlN/p-Ge interface.

• 대한금속재료학회지
• /
• 제49권6호
• /
• pp.498-504
• /
• 2011

We examined the microstructure and optical properties of crystallized ~30 nm-ZnO/~10 nm amorphous $TiO_2$ nano bilayered films as nano electrodes were deposited at extremely low substrate temperatures of $150-210^{\circ}C$. The bilayered films were deposited on silicon substrates with 10 cm diameters by ALD (atomic layer deposition) using DEZn (diethyl zinc(Zn(C2H5)2)) and TDMAT (tetrakis dimethyl-amid $titanium(Ti(N(CH_3)_2)_4)$ as the ZnO and $TiO_2$ precursors, respectively, and $H_2O$ as the oxidant. The microstructure, phase, and optical properties of the bilayered films were examined by FE-SEM, TEM, XRD, AES, and UV-VIS-NIR spectroscopy. FE-SEM and TEM showed that all bilayered films were deposited very uniformly and showed crystallized ZnO and amorphous $TiO_2$ layers. AES depth profiling showed that the ZnO and $TiO_2$ films had a stoichiometric composition of 1:1 and 1:2, respectively. These bilayered films have optical absorption properties in a wide range of ultraviolet wavelengths, 250-390 nm, whereas the single ZnO and $TiO_2$ films showed an absorption range of 350-380nm.

• 한국전기전자재료학회논문지
• /
• 제36권2호
• /
• pp.125-128
• /
• 2023

Recently, as the process of the MOS device becomes more detailed, and the degree of integration thereof increases, many problems such as leakage current due to an increase in electron tunneling due to the thickness of SiO₂ used as a gate oxide have occurred. In order to overcome the limitation of SiO₂, many studies have been conducted on HfO₂ that has a thermodynamic stability with silicon during processing, has a higher dielectric constant than SiO₂, and has an appropriate band gap. In this study, HfO₂, which is attracting attention in various fields, was doped with Al and the change in properties according to its concentration was studied. Al-doped HfO₂ thin film was deposited using Plasma Enhanced Atomic Layer Deposition (PEALD), and the structural and electrical characteristics of the fabricated MIM device were evaluated. The results of this study are expected to make an essential cornerstone in the future field of next-generation semiconductor device materials.

• 마이크로전자및패키징학회지
• /
• 제27권4호
• /
• pp.119-125
• /
• 2020

1.1~2.1eV의 직접 천이형 밴드갭을 가지는 전이금속 칼코게나이드(Transition Metal Dichalcogenide, TMDC)는 빛에 대한 반응성이 크고 구조적 특징상 2차원 물질들과의 수직 이종접합구조를 형성하기 용이하다는 장점으로 차세대 광전소자와 반도체소자 물질로서 대두되고 있다. 하지만 TMDC를 얻는 공정들의 한계로 인해 고품질, 대면적의 수직이종접합구조의 형성에 어려움이 존재한다. 본 연구에서는 MOCVD 시스템을 제작하고, 단일층 TMDC 및 이들의 이종구조에 제조에 대한 연구를 수행하였다. 특히, 버블러 타입의 유기금속화합물 소스를 활용하여, 반응기 내로 유입되는 소스의 농도와 유량을 정밀하게 조절함으로써 전면적으로 균일한 박막을 얻을 수 있다. MOCVD로 MoS2, WS2 박막을 성장시키고 주사전자현미경, UV-visible spectrophotometer, Raman spectroscopy, photoluminescence 분석을 진행하여 균일한 박막을 성장시켰음을 확인하였다. 또한, MoS2 박막에 WS2 박막을 직접 성장시킴으로써 MoS2/WS2 수직 이종접합구조를 형성하였다.

• 한국분말재료학회지
• /
• 제22권5호
• /
• pp.321-325
• /
• 2015

The triboelectric property of a material is important to improve an efficiency of triboelectric generator (TEG) in energy harvesting from an ambient energy. In this study, we have studied the TEG property of a semiconducting $SnO_2$ which has yet to be explored so far. As a counter triboelectric material, PET and glass are used. Vertical contact mode is utilized to evaluate the TEG efficiency. $SnO_2$ thin film is deposited by atomic layer deposition on bare Si wafer for various thicknesses from 5.2 nm to 34.6 nm, where the TEG output is increased from 13.9V to 73.5V. Triboelectric series are determined by comparing the polarity of output voltage of 2 samples among $SnO_2$, PET, and glass. In conclusion, $SnO_2$, as an intrinsic n-type material, has the most strong tendency to be positive side to lose the electron and PET has the most strong tendency to be negative side to get the electron, and glass to be between them. Therefore, the $SnO_2$-PET combination shows the highest TEG efficiency.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.154-155
• /
• 2012

The promise of nano-crystalites (nc) as a technological material, for applications including display backplane, and solar cells, may ultimately depend on tailoring their behavior through doping and crystallinity. Impurities can strongly modify electronic and optical properties of bulk and nc semiconductors. Highly doped dopant also effect structural properties (both grain size, crystal fraction) of nc-Si thin film. As discussed in several literatures, P atoms or radicals have the tendency to reside on the surface of nc. The P-radical segregation on the nano-grain surfaces that called self-purification may reduce the possibility of new nucleation because of the five-coordination of P. In addition, the P doping levels of ${\sim}2{\times}10^{21}\;at/cm^3$ is the solubility limitation of P in Si; the solubility of nc thin film should be smaller. Therefore, the non-activated P tends to segregate on the grain boundaries and the surface of nc. These mechanisms could prevent new nucleation on the existing grain surface. Therefore, most researches shown that highly doped nc-thin film by using conventional PECVD deposition system tended to have low crystallinity, where the formation energy of nucleation should be higher than the nc surface in the intrinsic materials. If the deposition technology that can make highly doped and simultaneously highly crystallized nc at low temperature, it can lead processes of next generation flexible devices. Recently, we are developing a novel CVD technology with a neutral particle beam (NPB) source, named as neutral beam assisted CVD (NBaCVD), which controls the energy of incident neutral particles in the range of 1~300eV in order to enhance the atomic activation and crystalline of thin films at low temperatures. During the formation of the nc-/pm-Si thin films by the NBaCVD with various process conditions, NPB energy directly controlled by the reflector bias and effectively increased crystal fraction (~80%) by uniformly distributed nc grains with 3~10 nm size. In the case of phosphorous doped Si thin films, the doping efficiency also increased as increasing the reflector bias (i.e. increasing NPB energy). At 330V of reflector bias, activation energy of the doped nc-Si thin film reduced as low as 0.001 eV. This means dopants are fully occupied as substitutional site, even though the Si thin film has nano-sized grain structure. And activated dopant concentration is recorded as high as up to 1020 #/$cm^3$ at very low process temperature (＜ $80^{\circ}C$) process without any post annealing. Theoretical solubility for the higher dopant concentration in Si thin film for order of 1020 #/$cm^3$ can be done only high temperature process or post annealing over $650^{\circ}C$. In general, as decreasing the grain size, the dopant binding energy increases as ratio of 1 of diameter of grain and the dopant hardly be activated. The highly doped nc-Si thin film by low-temperature NBaCVD process had smaller average grain size under 10 nm (measured by GIWAXS, GISAXS and TEM analysis), but achieved very higher activation of phosphorous dopant; NB energy sufficiently transports its energy to doping and crystallization even though without supplying additional thermal energy. TEM image shows that incubation layer does not formed between nc-Si film and SiO2 under later and highly crystallized nc-Si film is constructed with uniformly distributed nano-grains in polymorphous tissues. The nucleation should be start at the first layer on the SiO2 later, but it hardly growth to be cone-shaped micro-size grains. The nc-grain evenly embedded pm-Si thin film can be formatted by competition of the nucleation and the crystal growing, which depend on the NPB energies. In the evaluation of the light soaking degradation of photoconductivity, while conventional intrinsic and n-type doped a-Si thin films appeared typical degradation of photoconductivity, all of the nc-Si thin films processed by the NBaCVD show only a few % of degradation of it. From FTIR and RAMAN spectra, the energetic hydrogen NB atoms passivate nano-grain boundaries during the NBaCVD process because of the high diffusivity and chemical potential of hydrogen atoms.

• Journal of Periodontal and Implant Science
• /
• 제38권sup2호
• /
• pp.373-384
• /
• 2008

Purpose: The aim of this study is to compare the healing response of various Hydroxyapatite(HA) coated dental implants by Ion-Beam Assisted Deposition(IBAD) placed in the surgically created circumferential gap in dogs. Materials and methods: In four mongrel dogs, all mandibular premolars and the first molar were extracted. After an 8 weeks healing period, six submerged type implants were placed and the circumferential cylindrical 2mm coronal defects around the implants were made surgically with customized step drills. Groups were divided into six groups : anodized surface, anodized surface with 150nm HA and heat treatment, anodized surface with 300nm HA and heat treatment, anodized surface with 150nm HA and no heat treatment, and anodized surface with 150nm HA, heat treatment and bone graft, anodized surface with bone graft. The dogs were sacrificed following 12 weeks healing period. Specimens were analyzed histologically and histomorphometrically. Results: During the healing period, healing was uneventful and implants were well maintained. Anodized surface with HA coating and $430^{\circ}C$ heat treatment showed an improved regenerative characteristics. Most of the gaps were filled with newly regenerated bone. The implant surface was covered with bone layer as base for intensive bone formation and remodeling. In case that graft the alloplastic material to the gaps, most of the coronal gaps were filled with newly formed bone and remaining graft particles. The bone-implant contact and bone density parameters showed similar results with the histological findings. The bone graft group presented the best bone-implant contact value which had statistical significance. Conclusion: Within the scope of this study, nano-scale HA coated dental implants appeared to have significant effect on the development of new bone formation. And additional bone graft is an effective method in overcoming the gaps around the implants.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.41-41
• /
• 2007

For use in spintronic materials, dilute magnetic semiconductors (DMS) are under consideration as spin injectors for spintronic devices[l]. $TiO_2$-based DMS doped by a cobalt, iron, and manganese et al. was recently reported to show ferromagnetic properties, even at temperatures above 300K and the magnetic ordering was explained in terms of carrier-induced ferromagnetism, as observed for a III-V based DMS. An anomalous Hall effect (AHE) and co-occurance of superparamagnetism in reduced Co-doped rutile $TiO_{2-\delta}$ films have also been reported[2]. Metal segregation in the reduced metal-doped rutile $TiO_2-\delta$ films still remains as problems to solve the intrinsic DMS properties. Superlattice films have been proposed to get dilute magnetic semiconductor (DMS) with intrinsicroom-temperature ferromagnetism. For a $TiO_2$-based DMS superlattice structure, each layer was alternately doped by two different transition metals (Fe and Mn) and deposited to a thickness of approximately $2.7\;{\AA}$ on r-$Al_2O_3$(1102) substrates by pulsed laser deposition. The r-$Al_2O_3$(1102) substrates with atomic steps and terrace surface were obtained by thermal annealing. Samples of $Ti_{0.94}Fe_{0.06}O_2$(TiFeO), $Ti_{0.94}Mn_{0.06}O_2$(TiMnO), and $Ti_{0.94}(Fe_{0.03}Mn_{0.03})O_2$ show a low remanent magnetization and coercive field, as well as superparamagnetic features at room temperature. On the other hand, superlattice films (TiFeO/TiMnO) show a high remanent magnetization and coercive field. An anomalous Hall effect in superlattice films exhibits hysisteresis loops with coercivities corresponding to those in the ferromagnetic Hysteresis loops. The superlattice films composed of alternating layers of $Ti_{0.94}Fe_{0.06}O_2$ and $Ti_{0.94}Mn_{0.06}O_2$ exhibit intrinsic ferromagnetic properties for dilute magnetic semiconductor applications.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.234-234
• /
• 2010

최근 CMOS 소자 크기가 축소됨에 따라 소스와 드레인 영역에서의 접촉저항을 줄이기 위하여, 실리사이드 공정이 많이 연구되고 있다. 실리사이드 물질로서 NiSi는 낮은 저항률과 낮은 실리콘 소모, 낮은 공정온도, 등의 장점을 가지고 있다. 그러나, 실리사이드 형성으로 인한 나노소자의 소오스/드레인에서정션(junction) 누설전류의 증가는 큰 문제가 되므로 실리콘과 실리사이드 계면의 특성이 중요하다. 본 연구에서는 니켈을 이용한 실리사이드 형성시 계면 활성제인 에틸 요오드를 이용하여 실험을 진행하였다. 금속 유기 전구체인 MABONi을 사용하여 ALD 방식으로 증착 한 니켈 박막과 니켈 핵 형성시 계면활성제인 에틸요오드의 처리 방법에 따른 Ni-silicide 박막의 특성을 비교, 분석하였다. 먼저 자연산화막을 건식식각으로 제거한 뒤, 첫 번째 샘플에서는 10회의 주기로 초기 니켈을 증착한 뒤, 에틸요오드로 니켈의 표면 위를 처리하고, 다시 200회의 주기로 니켈을 증착하였으며, 두 번째는 첫 번째 방식에서 에틸요오드 주입 시 동시에 수소도 함께 주입하였다. 세 번째는 비교를 위해 에틸요오드 처리를 하지 않고 니켈 박막만을 증착 하였다. 이어서, 각 샘플을 급속 열처리 장비에서 $400^{\circ}C$부터 $900^{\circ}C$까지 각각 30sec간 열처리를 진행후, 반응하지 않은 잔여 니켈을 제거한 후, XRD(x-ray diffraction), AES(auger), 그리고 4-point probe 등을 이용하여 형성된 실리사이드의 특성을 분석하였다. 에틸요오드와 함께 수소를 주입한 경우 계면에서의 산소 불순물과 카본 성분이 효과적으로 제거되어 $400^{\circ}C$에서 $2.9{\Omega}/{\Box}$ 의 낮은 면저항을 가지는 NiSi가 형성되었고 모든 온도구간에서 다른 샘플에 비하여 가장 낮은 면저항 분포를 보였다. 이는 분해 흡착된 요오드에 의한 계면 특성 향상과 카본 성분이 포함된 잔여물들이 수소처리에 의해 효율적으로 제거되어 실리사이드의 특성이 향상되었기 때문이다. 계면활성제를 사용하지 않은 경우에는 $500^{\circ}C$에서 NiSi가 형성되었다. 반면에 에틸요오드로만 표면을 처리한 경우에는 니켈과 실리콘 계면에서의 카본 성분에 의하여 silicidation 이 충분히 일어나지 않았다. 이러한 결과는 향후 45nm 이하의 CMOS 공정상에서 소스와 드레인의 낮은 누설전류를 가지고, 접촉저항을 줄이기 위한 니켈 실리사이드 형성에 큰 도움을 줄 것으로 기대된다.

• 한국전기전자재료학회논문지
• /
• 제36권1호
• /
• pp.88-92
• /
• 2023

The ferroelectricity in Hf_0.5Zr_0.5O₂ (HZO) thin films is one of the most interesting topics for next-generation nonvolatile memory applications. It is known that a crystallization process is required at a temperature of 400℃ or higher to form an orthorhombic phase that results in the ferroelectric properties of the HZO film. However, to realize the integration of ferroelectric HZO films in the back-end-of-line, it is necessary to reduce the annealing temperature below 400℃. This study aims to comprehensively analyze the ferroelectric properties according to the annealing temperature (350-500℃) and time (1-5 h) using a furnace as a crystallization method for HZO films. As a result, the ferroelectric behaviors of the HZO films were achieved at a temperature of 400℃ or higher regardless of the annealing time. At the annealing temperature of 350℃, the ferroelectric properties appeared only when the annealing time was sufficiently increased (4 h or more). Based on these results, it was experimentally confirmed that the optimization of the annealing temperature and time is very important for the ferroelectric phase crystallization of HZO films and the improvement of their ferroelectric properties.