• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.119-119
• /
• 2015

Ion beam sputtering has been widely used in Secondary Ion Mass Spectrometry (SIMS), X-ray Photoelectron Spectroscopy (XPS), and Auger Electron Spectroscopy (AES) for depth profile or surface cleaning. However, mainly due to severe matrix effects such as surface composition change from its original composition and damage of the surface generated by ion beam bombardment, conventional sputtering skills using mono-atomic primary ions with energy ranging from a few hundred to a thousand volts are not sufficient for the practical surface analysis of next-generation organic/inorganic device materials characterization. Therefore, minimization of the surface matrix effects caused by the ion beam sputtering is one of the key factors in surface analysis. In this work, the electronic structure of a $Ta_2O_5$ thin film on $SiO_2/Si$ (100) after Ar Gas Cluster Ion Beam (GCIB) sputtering was investigated using X-ray photoemission spectroscopy and compared with those obtained via mono-atomic Ar ion beam sputtering. The Ar ion sputtering had a great deal of influence on the electronic structure of the oxide thin film. Ar GCIB sputtering without sample rotation also affected the electronic structure of the oxide thin film. However, Ar GCIB sputtering during sample rotation did not exhibit any significant transition of the electronic structure of the $Ta_2O_5$ thin films. Our results showed that Ar GCIB can be useful for potential applications of oxide materials with sample rotation.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.11
• /
• pp.15-19
• /
• 2007

This paper reports the effects of Ar ion beam surface treatment on a $SiO_2$ dielectric layer in organic thin film transistors. We compared the electrical properties of pentacene-based OTFTs, treated by $O_2$ plasma or Ar ion beam treatments and characterized the states of the surface of the dielectric by using atomic force microscopy and X-ray photoelectron spectroscopy. For the sample which received $O_2$ plasma treatment, the mobility increased significantly but the on/off current ratio was found very low. The Ar ion beam-treated sample showed a very high on/off current ratio as well as a moderately improved mobility. XPS data taken from the dielectric surfaces after each of treatments exhibit that the ratio of between Si-O bonds and O-Si-O bonds was much higher in the $O_2$ plasma treated surface than in the Ar ion beam treated surface. We believe that our surface treatment using an inert gas, Ar, carried out an effective surface cleaning while keeping surface damage very low, and also the improved device performances was achieved as a consequence of improved surface condition.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.98-98
• /
• 2010

Ion beam irradiation has been extensively used for surface modification of polymers, glassy metals and amorphous and crystalline materials at micron and submicron scales. The surface structures created by exposure to an ion beam range from dots, steps and one-dimensional straight wrinkles to highly complex hierarchical undulations and ripples. In general, the morphology of these nanoscale features can be selected by controlling the ion beam parameters (e.g. fluence and acceleration voltage), making ion beam irradiation a promising method for the surface engineering of materials. In the work, we presented that ion beam irradiation results in creation of a peculiar nanoscale dimple-like structure on the surface of polyimide - a common polymer in electronics, large scale structures, automobile industry, and biomedical applications. The role of broad Ar ion beam on the morphology of the structural features was investigated and insights into the mechanisms of formation of these nanoscale features were provided. Moreover, a systematic experimental study was performed to quantify the role of ion beam treatment time, and thus the morphology, on the coefficient of friction of polyimide surfaces covered by nanostructure using a tribo-experiment. Nano-indentation experiment were performed on the ion beam treated surfaces which shows that the hardness as well as the elastic modulus of the polyimide surface increased with increase of Ar ion beam treatment time. The increased of hardness of polyimide have been explained in terms of surface structure as well as morphology changes induced by Ar ion beam treatment.

• Journal of the Korean Ceramic Society
• /
• v.40 no.12
• /
• pp.1165-1169
• /
• 2003

The Ta$_2$O$_{5}$ thin film was deposited on Si-(III) and glass substrate with the change of Ar:O$_2$ gas flow rate in the assist ion gun by the Dual ion-Beam Sputtering (DIBS). As the $O_2$ gas flow of the assist ion gun was decreased, the deposition rate of the thin films decreased. The refractive index was fixed (2.11, at 1550 nm) without regarding to $O_2$ gas flow of the range 3∼12 sccm in assist ion gun. The condition of Ar:O$_2$=3:12 was formatted stoichiometry composition of Ta$_2$O$_{5}$ and the ms roughness was small (0.183 nm).

• Polymer(Korea)
• /
• v.26 no.6
• /
• pp.718-727
• /
• 2002

In this work, an Ar+ beam was irradiated on carbon fiber surfaces to improve the interfacial shear strength (IFSS) of the resulting composites using an ion assisted reaction (IAR) method h single fiber pull-out test was executed to investigate the basic characteristics of the single Carbon fiber/matrix interface. Based on Greszczuk's geometrical model, the debonding force for pull-out of the fiber from the resins was discussed with the applied ion beam energy as a result, it was known that an ion beam treatment produced the functional groups on fiber surface and etching lines along the fiber axis direction, resulting in increasing the adhesion forces between fibers and matrix, which caused the improvement of the IFSS in a composite system. And, it was also found that the maximum IFSS was shown at 0.8 keV ion beam energy in this system.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1994.02a
• /
• pp.132-132
• /
• 1994

• Applied Microscopy
• /
• v.45 no.4
• /
• pp.189-194
• /
• 2015

Backside Ar ion milling technique for the preparation of cross-sectional transmission electron microscopy (TEM) specimens, and backside-ion milling combined with focused ion beam (FIB) operation for electron holography were introduced in this paper. The backside Ar ion milling technique offers advantages in preparing cross-sectional specimens having thin, smooth and uniform surfaces with low surface damages. The back-side ion milling combined with the FIB technique could be used to observe the two-dimensional p-n junction profiles in semiconductors with the sample quality sufficient for an electron holography study. These techniques have useful applications for accurate TEM analysis of the microstructure of materials or electronic devices such as arrayed hole patterns, three-dimensional integrated circuits, and also relatively thick layers (> $1{\mu}m$).

• Journal of the Korean Society for Heat Treatment
• /
• v.25 no.6
• /
• pp.279-282
• /
• 2012

$SnO_2$ thin films were prepared on the Si substrate by radio frequency (RF) magnetron sputtering and then surface of the films were irradiated with intense Ar ion beam to investigate the effect of Ar ion irradiation on the properties and hydrogen gas sensitivity of the films. From atomic force microscope observation, it is supposed that intense Ar bombardments promote rough surface and increase gas sensitivity of $SnO_2$ films for hydrogen gas. The films that Ar ion beam irradiated at 6 keV show the higher sensitivity than the films were irradiated at 3 keV and 9 keV. These results suggest that the $SnO_2$ thin films irradiated with optimized Ar ion beam are promising for practical high-performance hydrogen gas sensors.

• The Korean Journal of Ceramics
• /
• v.2 no.1
• /
• pp.48-53
• /
• 1996

Ion beam assisted crystallization behavior of sol-gel derived $PbTiO_3$ thin films, deposited on bare silicon(100) substrates by spin-casting method, has been investigated. Ar ion bombardment was directly conducted on the spincoated film surface with or without heating the film from room temperature to $300^{\circ}C$. Ion dose was changed from $5{\times}10^{15}$ to $7.5{\times}10^{16}$ $Ar^-/cm^2$. Formation of (110) oriented perovskite phase was obseerved with ion dose above $5{\times}10^{16}\; Ar^+/cm^2$. Crystallization of $PbTiO_3$ thin film could be enhanced with increasing the Air ion dose, or heating the substrate during ion bombardment. Crystallization of the $PbTiO_3$ films by ion bombardment was related to the local heating effect during ion bombardment.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.91-94
• /
• 1999

A new type of high-T$_c$ superconducting Josephson junctions has been prepared by Ar ion beam etching and electron beam lithography. YBa$_2Cu_3O_{7-x}$ (YBCO) films deposited on (001) SrTiO$_3$ single crystal substrate by pulsed laser deposition were patterned by Ar ion milling with photolithography. The narrow slit with a electroresist mask, about 1000 ${\AA}$ wide, was constructed over a 3 ${\sim}$ 5 ${\mu}$m bridge of a 1200-${\AA}$-thick YBCO film by electron beam lithography. The slit was then etched by the Ar ion beam to form a damaged 600-${\AA}$-thick YBCO. Thus prepared structure forms an S-N-S (YBCO - damaged YBCO - YBCO) type Josephson junctions. Those junctions exhibit RSI-like I-V characteristics at 77 K. The properties of the Josephson junctions such as I$_c$ R$_N$, and J$_c$ were characterized.