• 한국전자파학회논문지
• /
• 제25권1호
• /
• pp.62-69
• /
• 2014

본 논문에서는 WBAN(Wireless Body Area Network) On-body 시스템에서 표면 지향 안테나를 사용하여 인체 내부 기관에 의한 영향을 분석하였다. 인체 내부 기관의 영향을 확인하기 위하여 인체 상반신 모델과 실제 인체에 안테나를 부착하여 수신 신호의 세기를 측정하였다. 실험은 인체에 대한 고유 영향을 보기 위하여 무반향실에서 움직임 없이 수행하였고, VNA(Vector Network Analyzer)를 이용하여 수신 신호 세기를 측정하였다. 측정된 데이터를 이용하여 인체 모델과 상반신 모델의 수신 신호 세기를 비교하였고, 인체 내부 기관이 안테나 수신 신호 세기에 미치는 효과를 분석하였다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2004년도 ICEIC The International Conference on Electronics Informations and Communications
• /
• pp.181-184
• /
• 2004

In this paper, we propose the dual band(2.4GHz and 5GHz) antenna for access point of WLAN(Wireless Local Area Network) which has similar radiation patterns for each band. Simulation results by using HFSS(High Frequency Structure Simulator) for the proposed antenna are presented. The electrical characteristics of the proposed antenna are measured with HP 8510C network analyzer and included. And radiation patterns are measured with rectangular anechoic far field antenna chamber. Measured results show that $S_{11}$ is less than - 14dB and VSWR(Voltage Standing Wave Ratio) is less than 1.5 for all frequency bands of interest. The measured maximum gain for elevation pattern at 2.40GHz is about 2.46dBi at $theta=-78^{\circ}$ and maximum gain for 5.825GHz is about 2.70dBi at $theta=-80^{\circ}.$ And the implemented antenna has good radiation pattern characteristic, therefore, we expect that the implemented dual band antenna is applicable for access point of WLAN.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권4호
• /
• pp.471-477
• /
• 2014

In this paper, a modeling and co-simulation methodology is proposed to predict the radiated electromagnetic interference (EMI) from on-chip switching I/O buffers. The output waveforms of I/O buffers are simulated including the on-chip I/O buffer circuit and the RC extracted on-chip interconnect netlist, package, and printed circuit board (PCB). In order to accurately estimate the EMI, a full-wave 3D simulation is performed including the measurement environment. The simulation results are compared with near-field electromagnetic scan results and far-field measurements from an anechoic chamber, and the sources of emission peaks were analyzed. For accurate far-field EMI simulation, PCB power trace models considering IC switching current paths and external power cable models must be considered for accurate EMI prediction. With the proposed EMI simulation model and flow, the electromagnetic compatibility can be tested even before the IC is fabricated.

• Journal of electromagnetic engineering and science
• /
• 제1권1호
• /
• pp.95-99
• /
• 2001

According to the progress of the electronic industy and radio communication technologies, mankind might enjoy its abundant life On the other hand, many social problems such as EMI, and unnecessary electromagnetic wave occur due to the increased use of electromagnetic wave. Therefore, the organiztions such as CISPR, FCC, ANSl,etc. have provided the standard of electromagnetic wave enviroment for the countermeasure of the EMC. It had been required that the absorbing ability of an electromagnetic wave absorber is more than 20 dB, the bandwidth of which is required through 30 MHz to 1,000 MHz for satisfying the international standard about an anechoic chamber for EMI/EMS measurment. From November of 1998, however, the CISPRll has accepted the extended frequency band from 1 GHz to 18 GHz additionally in the bandwidth of EMI measurementent$^{[1]}$ . In this paper, we proposed a new type absorber satisfying the above requirements and carried out broadband design using the equivalent material constants method. Futheremore, the experiments were carried out over the frequency band from 30 MHz to 2 GHz, and hence, the validity of the proposed design theory was confirmed.

• 전기학회논문지
• /
• 제59권2호
• /
• pp.369-373
• /
• 2010

Modem electronic circuits are of importance for the function of communication, traffic systems and security systems. An intentional threat to these systems could be of big casualties and economic disasters. This paper has shown damage effect of microcontroller device with coupling caused by UWB-HPEM(Ultra Wideband-High Power Electromagnetics). The UWB measurements were done at an Anechoic Chamber using a RADAN UWB voltage source, which can generate a transient impulse of about 180 kV. The susceptibility level for microcontroller has been assessed by effect of various operation line lengths. The results of susceptibility analysis has showed that the effect of the reset line length on the MT(Ma1function Threshold) is larger than the effect of the different line length(Data, Power, Clock). With the knowledge of these parameters electronic system can be designed exactly suitable concerning the system requirements. Based on the results, susceptibility of microcontroller can be applied to protection plan to elucidate the effects of microwaves on electronic equipment.

• Journal of Electrical Engineering and Technology
• /
• 제7권3호
• /
• pp.389-395
• /
• 2012

In this paper, we analyzed the frequency spectrum of the electromagnetic waves radiated by an electric discharge as a basic study to develop an on-line diagnostic technique for power equipment installed inside closed-switchboards. In order to simulate local and series arc discharges caused by an electric field concentration and poor connections, three types of electrode systems were fabricated, consisting of needle and plane electrodes and an arc generator meeting the specifications of UL 1699. The experiment was carried out in an electromagnetic anechoic chamber, and the measurement system consisted of a PD free transformer, a loop antenna with a frequency bandwidth of 150 kHz-30 MHz, an ultra log periodic antenna with a frequency bandwidth of 30 MHz-2 GHz, and an EMI test receiver with a frequency bandwidth of 3 Hz-3 GHz. According to the experimental results, the frequency spectra of the electrical discharges were widely distributed across a range of 150 kHz-400 MHz, depending on the defects, while commonly found between 150 kHz and 10 MHz. Therefore, considering the ambient noise and antenna characteristics, the best frequency bandwidth for a measurement system to monitor abnormal conditions by detecting electromagnetic waves in closedswitchboards is 150 kHz-10 MHz.

• 대한기계학회논문집B
• /
• 제33권2호
• /
• pp.79-84
• /
• 2009

Turbocharger has been widely used in many passenger cars in application with diesel engines because of high power and fuel efficiency. However, flow-induced noise (whoosh or hissing noise) which is generated within a compressor during its operation at marginal surge line can deteriorate noise characteristics. Hissing noise excitation is associated with the generation of turbulence within the turbocharger compressor and radiated through the transmission path in a turbocharger system. In this study, a expansion muffler with lids is devised and installed in the transmission path to reduce the hissing noise. Acoustic and fluid dynamic characteristics for the muffler are investigated which are related to the unsteadiness of turbulence and pressure in the turbocharger system. A transfer matrix method is used to analyze the transmission loss of the muffler. A simple expansion muffler with lids is proposed for the reduction of high frequency component noise. Turbulence simulation is carried out by a standard k - ${\varepsilon}$ model. An optimal design condition of the muffler is obtained by extensive acoustic and fluid dynamic analysis on the engine dynamometer with anechoic chamber. A significant reduction of the hissing noise is achieved at the optimal design of the muffler as compared with the conventional muffler.

• 설비공학논문집
• /
• 제19권11호
• /
• pp.789-796
• /
• 2007

It has been noted, in case of the apartments in collective form, the drainage noise from cleaning of toilet causes many problems in the basement and adjacent rooms, mainly hampering the pleasant housing environment. The problems are increasingly raised by civil complaints with the public offices. Therefore, if the drainage noise generates when wash out of toilet bowl is grasped how the characteristics change according to the sorts of drainpipe, it is considered that the establishment of an effective sound insulation countermeasure could be possible when a civil petition against the drainage noise of apartment house is submitted hereafter. On such viewpoint, this study measured and analyzed the characteristics of drainage noise per the type of drainage pipe, according to KS A ISO $1996-1{\sim}3$, with the horizontal branch pipe and riser pipes in the drainage noise experiment chamber which has the characteristics of the anechoic room. In the result, the pipe type with excellent noise reduction function. The result of this study is considered to become available as fundamental data, to take actions on reduction of drainage noise of the ceiling piping method.

• 대한전자공학회논문지SP
• /
• 제46권5호
• /
• pp.80-90
• /
• 2009

본 논문에서는 냉장고로부터 방사되는 소음에 대한 사용자의 불쾌도를 객관적으로 평가하기 위한 방법을 제안하였다. 이를 위해 8개의 상용 냉장고로부터 방사되는 소음이 무향실과 아파트로부터 녹음되었다. 사용자가 냉장고 소음으로부터 느끼는 주관적 청감을 알아보기 위하여 100명의 평가자로부터 청감 실험을 통하여 각 냉장고 소음의 주관적 평가 데이터가 얻어졌다. 그리고 이로부터 심리 음향 속성을 나타내는 파라미터인 5개의 Sound Quality Metric (SQM) 도출하였다. 마지막으로 주관적 소음 평가 데이터와 5개의 객관적 SQM 값 사이에 높은 상관도를 부여하는 냉장고 소음에 대한 객관적 평가 모델이 제시된다.

• 한국유체기계학회 논문집
• /
• 제7권5호
• /
• pp.13-19
• /
• 2004

Centrifugal blowers are widely used for air handling units in industry applications. The blower has a centrifugal impeller and a scroll casing including a driving component such as an electric motor. The impeller takes forward or backward blades to induce flows into the blower, Comprehensive investigation according to the two kinds of blades is systematically carried out for a guidance of design for this kind research. It is observed that flow rate of the blower with forward blades is larger than that of the system with backward blades. Otherwise, the system noise is more pronounced in the case of the blower with forward blades. The reason is due to larger velocity from the rotating forward blades that pose obtuse angle with the circumferential direction. The distinguished characteristics are validated by a parallel experiments with a wind tunnel and in an anechoic chamber. Numerical analysis for the system shows detail information inside the blades and the casing. A series of figures to show the flow details offer deep understanding of the performance of a centrifugal blower with different blades.