• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.9
• /
• pp.669-675
• /
• 2008

The objectives of this paper are to examine the effect of nano-particles on the pool type absorption heat transfer enhancement and to find the optimal conditions to design a highly effective compact absorber for ammonia/water absorption system. The effect of $Al_2O_3$ nano-particles and carbon nanotube(CNT) on the absorption performance is studied experimentally. The experimental ranges of the key parameters are 20% of ammonia concentration, $0{\sim}0.08\;vol%$ (volume fraction) of CNT particles, and $0{\sim}0.06 \;vol%$ of $Al_2O_3$ nano-particles. For the ammonia/water nanofluids, the heat transfer rate and absorption rate with 0.02 vol% $Al_2O_3$ nano-particles were found to be 29% and 18% higher than those without nano-particles, respectively. It is recommended that the concentration of 0.02 vol% of $Al_2O_3$ nano-particles be the best candidate for ammonia/water absorption performance enhancement.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.1
• /
• pp.47-51
• /
• 2010

A powder, containing 80 percent of blue cobalt aluminate $(CoAl_2O_4)$ crystallites, was synthesized at $210 ^{\circ}C$ using a (metal nitrate-malonic acid-ammonium hydroxide-ammonium nitrate) system. The optimal amount of concentrated ammonia water and initial decomposition temperature were determined for the blue $CoAl_2O_4$ crystallites preparation. Three $CoAl_2O_4$ precursor pastes, corresponding to the various amounts of concentrated ammonia water, were prepared by evaporating the initial solutions in an electric furnace fixed at $80 ^{\circ}C$ under a vacuum of 25 torr. The initial solution was used to dissolve the starting materials. The powder with the maximum content (80%) of blue $CoAl_2O_4$ crystallites was prepared when the prepared precursor was decomposed at $210 ^{\circ}C$. The blue $CoAl_2O_4$ crystallite content in the prepared sample decreased with increasing initial decomposition temperature. For 0.2 mole of the $Al^{3+}$ ion, the chemical compositions of the precursor corresponded to molar ratios of 0.4, 1.40, 2.56 and 2.00 for the $Co^{2+}$ ion, malonic acid, ammonia and ammonium nitrate per mole of the $Al^{3+}$ ion, respectively. The blue $CoAl_2O_4$ crystallite content in the sample decreased with the amount of ammonia deviated from the optimal value. The characteristics of the powders were examined using X-ray diffraction, optical microscopy, Fourier transformation infrared spectroscopy and the Brunauer-Emmett-Teller technique.

• Journal of the Korean Chemical Society
• /
• v.59 no.6
• /
• pp.493-498
• /
• 2015

The reductive amination of cyclohexanone with ammonia over Cu-Cr-a/γ-Al₂O₃ was investigated. It was found that a proper solvent with high solubility of ammonia and 4Å molecular sieves for the elimination of generated water contributed to the formation of cyclohexylamine in the premixing process. In addition, the addition of ammonia in the fixedbed reactor could obviously improve the conversion of cyclohexanone to cyclohexylamine. Finally, reaction conditions including reaction temperature, hydrogen pressure and charging rate of the premix were optimized. Under the optimized conditions, cyclohexylamine was obtained in 83.06% yield.

• Clean Technology
• /
• v.26 no.4
• /
• pp.263-269
• /
• 2020

Zeolite was synthesized hydrothermally using the water-treatment sludge, and the effects of various synthesis parameters like reaction temperature, reaction time, and Na2O/SiO2 molar ratio on the crystallization of zeolite were investigated. Crystal structure, physical property, and thermal stability of zeolite crystals were characterized by X-ray powder diffraction, FTIR spectroscopy, BET nitrogen adsorption, and TGA measurements. The removal efficiencies of nitrogen in ammonia, heavy metal ions, and TOC were calculated to evaluate zeolite's adsorption capacity. The primary chemical composition of water-treatment sludge was 28.79% Al2O3 and 27.06% SiO2. The zeolites were synthesized by merely employing the water-treatment sludge as silica and alumina sources without additional chemicals. Zeolite crystals synthesized through the water-treatment sludge were confirmed as an A-type zeolite structure. Zeolite A had the highest crystallinity obtained from a gel with the molar composition 2.1Na2O-Al2O3-1.6SiO2-65H2O after 5 h at a temperature of 90 ℃. The specific surface area of zeolite obtained was 55 ㎡ g-1, which was higher than commercial zeolite A. The removal efficiency of nitrogen in ammonia was 68% after 3 h of reaction time, while the removal efficiencies of Pb2+ and Cd2+ ions were 99.1% and 99.3%, respectively. These results indicate active ion exchange between Pb2+ or Cd2+ ion and Na+ ion in the zeolite framework. The adsorption experiments on the different zeolite addition conditions were performed for 3 h with 300 ppm humic acid. Based on the results, TOC's highest efficiency was 83% when 5 g of zeolite was added.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.412-415
• /
• 2017

In this study, the decomposition performance of ammonia dinitramide (ADN) based liquid monopropellant was evaluated by using metal supported alumina bead catalyst. Alumina bead was calcined at $1200^{\circ}C$, and Pt and Cu were impregnated on alumina bead by excess water impregnation using a rotary evaporator. The decomposition temperature ($T_{dec}$) of ADN-based liquid monopropellant was measured in a home-made batch reactor. The decomposition temperature of Cu/$Al_2O_3$ catalyst was lower than that of Pt/$Al_2O_3$ catalyst, and $T_{dec}$ was about $130^{\circ}C$.

• Resources Recycling
• /
• v.30 no.2
• /
• pp.39-45
• /
• 2021

Spent photovoltaic module is one of the important resource of silver, while related research concerning silver recovery remains limited. In our previous research, HNO3 was utilized to dissolve Ag(I) and Al(III) from the spent silicon solar cells. In order to recover Ag(I) from the leachate of a silicon solar cell, the present study made use of a nitrate solution containing Ag(I) and Al(III), which was subjected to a solvent extraction process with 5,8-diethyl-7-hydroxydodecan-6-oxime (LIX63). Ag(I) was selectively extracted with LIX63 over Al(III) from the nitrate leach solution. Subsequently, quantitative stripping of Ag(I) from the loaded LIX63 was performed by using 20% ammonia water. The McCabe-Thiele plots for the extraction and stripping isotherms of Ag(I) were also constructed. Extraction and stripping simulation tests confirmed an Ag(I) extraction and stripping efficiency of >99.99% and 98.9%, respectively with high purity Ag (99.998%) and Al (99.99%) solution. A process flow sheet for Ag(I) recovery from the nitrate leach solution was proposed.

• Korean Chemical Engineering Research
• /
• v.50 no.3
• /
• pp.435-441
• /
• 2012

The direct conversion of cellulose into polyols in $H_2$ was examined over Pt catalysts supported on various zeolites, viz., mordenite, Y, ferrierite, and ${\beta}$. For comparison, Pt catalysts supported on ${\gamma}-Al_2O_3$, $SiO_2-Al_2O_3$, and $SiO_2$ were also tested. The physical properties of the catalysts were probed with $N_2$ physisorption. The surface acidity was measured with temperature programmed desorption of ammonia ($NH_3$-TPD). The Pt content was quantified with inductively coupled plasma-atomic emission spectroscopy (ICP-AES). The Pt dispersion was determined with CO chemisorptions and transmission electron microscopy (TEM). The conversion of cellulose appeared to be mainly dependent on the reaction temperature and reaction time because it depends on the concentration of $H^+$ ions reversibly formed in hot water. Pt/H-mordenite (20) showed the highest yield to polyols among the tested catalysts. Pt/H-zeolite was superior to Pt/Na-zeolite for this reaction. The polyol yield was dependent on the surface acid density and the external surface area.

• Analytical Science and Technology
• /
• v.21 no.2
• /
• pp.123-128
• /
• 2008

The golden turbid solution of cordierite precursor was obtained by using magnesium ethoxide in sol-gel method, while the clear solution of cordierite precursor was obtained when 5%-$Zr(OC_3H_7)_4$ solution was used in the sol-gel reaction. $SiO_2$ component was confirmed by infrared spectra showing $1045cm^{-1}$ and the stretching vibration of gelish $SiO_4$ showed $1140cm^{-1}$ and $940cm^{-1}$. The component of $Al_2O_3$ showed at $580cm^{-1}$ and network structure of $Al_2O_6$ showed at $680cm^{-1}$. The component of MgO was confirmed at $575cm^{-1}$ as the stretching vibration. X-ray diffraction analysis showed ${\mu}$-cordierite crystal was showed up at temperature above $1000^{\circ}C$ at the mole ratio of cordierite precursor and water (1:5). ${\mu}$-Cordierite and ${\alpha}$-cordierite were coexisted at $1050^{\circ}C$ for the mole ratio of cordierite precursor and ammonia (1:5) while ${\alpha}$-cordierite was only existed at $1100^{\circ}C$ for the same mole ratio as mentioned above.

• Journal of Korean Society of Water and Wastewater
• /
• v.31 no.1
• /
• pp.103-114
• /
• 2017

A membrane bioreactor by sequentially alternating the inflow and by applying a two-stage coagulation control based on pre-coagulation was evaluated in terms of phosphorus removal efficiency and cost-savings. The MBR consisted of two identical alternative reaction tanks, followed by aerobic, anoxic and membrane tanks, where the wastewater and the internal return sludge alternatively flowed into each alternative reaction tank at every 2 hours. In the batch-operated alternative reaction tank, the initial concentration of nitrate rapidly decreased from 2.3 to 0.4 mg/L for only 20 minutes after stopping the inflow, followed by substantial release of phosphorus up to 4 mg/L under anaerobic condition. Jar test showed that the minimum alum doses to reduce the initial $PO_4$-P below 0.2 mg/L were 2 and 9 mol-Al/mol-P in the wastewater and the activated sludge from the membrane tank, respectively. It implies that a pre-coagulation in influent is more cost-efficient for phosphorus removal than the coagulation in the bioreactor. On the result of NUR test, there were little difference in terms of denitrification rate and contents of readily biodegradable COD between raw wastewater and pre-coagulated wastewater. When adding alum into the aerobic tank, alum doses above 26 mg/L as $Al_2O_3$ caused inhibitory effects on ammonia oxidation. Using the two-stage coagulation control based on pre-coagulation, the P concentration in the MBR effluent was kept below 0.2 mg/L with the alum of 2.7 mg/L as $Al_2O_3$, which was much lower than 5.1~7.4 mg/L as $Al_2O_3$ required for typical wastewater treatment plants. During the long-term operation of MBR, there was no change of the TMP increase rate before and after alum addition.

• Environmental Engineering Research
• /
• v.18 no.4
• /
• pp.267-276
• /
• 2013

This study presents a comparison of different protocols for the synthesis of iron-loaded zeolites, and the results of their application, as well as that of zeolite-A (Z-A), to the removal of ammonium and phosphate from aqueous media. Zeolites prepared by three methods were evaluated: iron-incorporated zeolites (IIZ), iron-exchanged zeolites (IEZ), and iron-calcined zeolites (ICZ). The optimal iron content for preparing of IIZ, as determined via scanning electron microscopy and X-ray photoelectron spectroscopy analyses, expressed as molar ratio of $SiO_2:Al_2O_3:Fe$, was below 0.05. Ammonia removal revealed that the iron-loaded zeolites have a higher removal capacity than that of Z-A due, not only to ion-exchange phenomena, but also via adsorption. Greater phosphate removal was achieved with IEZ than with ICZ; additionally, no sludge production was observed in this heterogeneous reaction, even though the coagulation process is generally accompanied by the production of a large amount of undesired chemical sludge. This study demonstrates that the developed synthetic iron-loaded zeolites can be applied as a heterogeneous nutrient-removal materials with no sludge production.