• Corrosion Science and Technology
• /
• 제22권2호
• /
• pp.90-98
• /
• 2023

In this study, cobalt oxide (Co₃O₄) and cobalt-doped magnetite (CoFe₂O₄) nanoparticles were synthesized by a hydrothermal method. They were then used as corrosion inhibitors for corrosion protection of AA2024-T3 aluminum alloys. These obtained nanoparticles were characterized by x-ray diffraction, field-emission scanning electron microscopy, and Zeta potential measurements. Corrosion inhibition activities of Co₃O₄ and CoFe₂O₄ nanoparticles were determined by performing electrochemical measurements for bare AA2024-T3 aluminum alloys in 0.05 M NaCl + 0.1 M Na₂SO₄ solution containing Co₃O₄ or CoFe₂O₄ nanoparticles. Corrosion protection for AA2024-T3 aluminum alloys by a water-based epoxy with or without the synthesized Co₃O₄ or CoFe₂O₄ nanoparticles was investigated by electrochemical impedance spectroscopy during immersion in 0.1 M NaCl solution. The corrosion protection of epoxy coating deposited on the AA2024-T3 surface was improved by incorporating Co₃O₄ or CoFe₂O₄ nanoparticles in the coating. The corrosion protection performance of the epoxy coating containing CoFe₂O₄ was higher than that of the epoxy coating containing Co₃O₄.

• 청정기술
• /
• 제15권3호
• /
• pp.194-201
• /
• 2009

최근 주요 수질오염 물질로 대두되고 있는 질산성 질소의 제거를 목적으로 영가 철 나노입자에 의한 질산성 질소의 환원반응성을 평가하였다. 영가 철 나노입자의 제조방법에 따른 반응성 차이를 규명하기 위해 유기용매 상에 계면활성제를 첨가하여 나노미터 크기 수준의 수용액 분산상에서 입자를 합성하는 마이크로에멀젼 방법과, 수용액 상의 철 이온을 환원시켜 입자를 합성하는 두 가지 방법으로 영가 철 나노입자를 합성하였다. 또한 전기영동법으로 알루미늄에 침적시킨 영가 철 나노입자에 의한 질산성 질소 제거속도를 측정하고, 고정화되지 않은 나노 철 입자에 의한 반응속도와 비교하였다. 환원반응을 질산성 질소에 대한 1차 반응으로 가정하여 수용액 방법 및 마이크로에멀전 방법으로 제조된 영가 철 나노입자의 반응성을 평가한 결과, 반응속도상수는 각각 $1.40{\times}10^{-2}min^{-1}$ 와 $3.49{\times}10^{-2}min^{-1}$ 로서 비표면적에 비례하여 증가하였다. 알루미늄에 침적된 나노입자는 현탁된 나노입자의 반응과 비교하여 약 30% 감소된 반응속도를 보였으나, 과량의 질산성 질소가 존재하는 경우 나노 철의 단위 질량당 질산성 질소의 제거효율 면에서 더 우수한 특성을 보였다. 나노철 입자의 현탁액은 반응시간 30분 이내에 반응속도가 감소하는 경향을 보였으나, 알루미늄에 침적된 나노철 입자는 3시간 이상 활성을 유지하였으며, 최종 생성물로 기체 질소를 발생시키는 것을 확인하였다.

• 한국분말재료학회지
• /
• 제24권3호
• /
• pp.242-247
• /
• 2017

In this study, the electroless nickel plating method has been investigated for the coating of Ni nanoparticles onto fine Al powder as promising energetic materials. The adsorption of nickel nanoparticles onto the surface of Al powders has been studied by varying various process parameters, namely, the amounts of reducing agent, complexing agent, and pH-controller. The size of nickel nanoparticles synthesized in the process has been optimized to approximately 200 nm and they have been adsorbed on the Al powder. TGA results clearly show that the temperature at which oxidation of Al mainly occurs is lowered as the amount of Ni nanoparticles on the Al surface increases. Furthermore, the Ni-plated Al powders prepared for all conditions show improved exothermic reaction due to the self-propagating high-temperature synthesis (SHS) between Ni and Al. Therefore, Al powders fully coated by Ni nanoparticles show the highest exothermic reactivity: this demonstrates the efficiency of Ni coating in improving the energetic properties of Al powders.

• Bulletin of the Korean Chemical Society
• /
• 제35권10호
• /
• pp.2917-2921
• /
• 2014

Cerium-activated yttrium aluminate ($Y_3Al_5O_{12}:Ce^{3+}$) exhibiting a garnet structure has been widely utilized in the production of light emitting diodes (LEDs) as a yellow emitting phosphor. The commercialized yttrium aluminum garnet (YAG) phosphor is typically synthesized by a solid-state reaction, which produces irregular shape particles with a size of several tens of micrometers by using the top-down method. To control the shape and size of particles, which had been the primary disadvantage of top-down synthetic methods, we synthesized YAG:Ce nanoparticles with a diameter of 500 nm using a coprecipitation method under the atmospheric pressure without the use of template or special equipment. The precursor particles were formed by refluxing an aqueous solution of the nitrate salts of Y, Al, and Ce, urea, and polyvinylpyrrolidone (55 K) at $100^{\circ}C$ for 12 h. YAG:Ce nanoparticles were formed by the calcination of precursor particles at $1100^{\circ}C$ for 10 h under atmospheric conditions. The phase identification, microstructure, and photoluminescent properties of the products were evaluated by X-ray powder diffraction, scanning electron microscopy, absorption spectrum and photoluminescence analyses.

• 대한화학회지
• /
• 제57권1호
• /
• pp.109-114
• /
• 2013

The effects of aluminum nanoparticles (AlNs) on the thermal decomposition of ammonia perchlorate (AP) were investigated by DSC, TG-DSC and DSC-TG-MS-FTIR. Addition of AlNs resulted in an increase in the temperature of the first exothermic peak of AP and a decrease in the second. The processing of non-isothermal data at various heating rates with and without AlNs was performed using Netzsch Thermokinetics. The dependence of the activation energy calculated by Friedman's isoconversional method on the conversion degree indicated the decomposition process can be divided into three steps. They were C1/D1/D1 for neat AP, determined by Multivariate Non-linear Regression, and changed to C1/D1/F2 after addition of AlNs into AP. The isothermal curves showed that the thermal stability of AP in the low temperature stage was improved in the presence of AlNs.

• Clinical and Experimental Vaccine Research
• /
• 제12권4호
• /
• pp.304-312
• /
• 2023

Purpose: Due to the many problems with commercially available vaccines, the production of effective vaccines against brucellosis is a necessity. The aim of this study was to evaluate the immune responses caused by the chimeric protein consisting of trigger factor, Bp26, and Omp31 (TBO) along with aluminum hydroxide (AH/TBO) and selenium (Se/TBO) nanoparticles (NPs) as adjuvants in mouse model. Materials and Methods: Recombinant antigen expression was induced in Escherichia coli BL21 (DE3) bacteria using IPTG (isopropyl-d-1-thiogalactopyranoside). Purification and characterization of recombinant protein was conducted through NiFe₃O₄ NPs, sodium dodecyl sulfate-polyacrylamide gel electrophoresis, and Western blot. NP characteristics, including morphology and particle size, were measured in vitro. The recombinant TBO was loaded on to AH and Se NPs and were administered subcutaneously. After mice immunization, measurement of antibody titter and protection assay was performed. Results: The average sizes of AH and Se NPs were about 60 nm and 150 nm, respectively. The enzyme-linked immunosorbent assay results showed that the serum of mice immunized by subcutaneous injection with both nanovaccines produced significant immunoglobulin G (IgG) responses against the chimeric antigen. The results of TBO-specific IgG isotype (IgG2a/IgG1) analysis showed that both AH and Se NPs induced a type to T-helper immune response. In addition, the results of the challenge with the pathogenic strain of Brucella melitensis 16M showed that vaccinated mice with AH/TBO NPs indicated a higher reduction of bacterial culture than immunized mice with Se/TBO NPs and TBO alone. Conclusion: The results showed that AH NPs carrying chimeric antigen can be a promising vaccine candidate against brucellosis by producing protective immunity.

• Toxicological Research
• /
• 제34권4호
• /
• pp.343-354
• /
• 2018

Aluminum oxide nanoparticles ($Al_2O_3$ NPs) are among the most widely used nanomaterials; however, relatively little information about their risk identification and assessment is available. In the present study, we aimed to investigate the potential toxicity of $Al_2O_3$ NPs following repeated inhalation exposure in male Sprague-Dawley rats. Rats were exposed to $Al_2O_3$ NPs for 28 days (5 days/week) at doses of 0, 0.2, 1, and $5mg/m^3$ using a nose-only inhalation system. During the experimental period, we evaluated the clinical signs, body weight change, hematological and serum biochemical parameters, necropsy findings, organ weight, and histopathology findings. Additionally, we analyzed the bronchoalveolar lavage fluid (BALF), including differential leukocyte counts, and aluminum contents in the major organs and blood. Aluminum contents were the highest in lung tissues and showed a dose-dependent relationship in the exposure group. Histopathology showed alveolar macrophage accumulation in the lungs of rats in the $5mg/m^3$ group during exposure and recovery. These changes tended to increase at the end of the recovery period. In the BALF analysis, total cell and neutrophil counts and lactate dehydrogenase, tumor necrosis factor-${\alpha}$, and interleukin-6 levels significantly increased in the 1 and $5mg/m^3$ groups during exposure. Under the present experimental conditions, we suggested that the no-observed-adverse-effect level of $Al_2O_3$ NPs in male rats was $1mg/m^3$, and the target organ was the lung.

• Journal of Electrochemical Science and Technology
• /
• 제14권1호
• /
• pp.15-20
• /
• 2023

Ionic liquids are considered as a promising, alternative solvent for the electrochemical synthesis of metals because of their high thermal and chemical stability, relatively high ionic conductivity, and wide electrochemical window. In particular, their wide electrochemical window enables the electrodeposition of metals without any side reaction of electrolytes such as hydrogen evolution. The electrodeposition of silver is conducted in 1-n-butyl-3-methylimidazolium chloride ([C4mim]Cl) ionic liquid system with a silver source of AgCl. This study is the first attempt to electrodeposit silver nanoparticles without using co-solvents other than [C4mim]Cl. Pulse electrolysis is employed for the synthesis of silver nanoparticles by varying applied potentials from -3.0 V to -4.5 V (vs. Pt-quasi reference electrode) and pulse duration from 0.1 s to 0.7 s. Accordingly, the silver nanoparticles whose size ranges from 15 nm to ~100 nm are obtained. The successful preparation of silver nanoparticles is demonstrated regardless of the kinds of substrate including aluminum, stainless steel, and carbon paper in the pulse electrolysis. Finally, the antimicrobial property of electrodeposited silver nanoparticles is confirmed by an antimicrobial test using Staphylococcus aureus.

• Current Photovoltaic Research
• /
• 제2권1호
• /
• pp.14-17
• /
• 2014

In this paper, indium reduced materials for transparent conductive electrodes (TCE) were fabricated and their physical properties were evaluated. Two of materials, indium-zinc-tin oxide (IZTO) and aluminum (Al) were selected as TCE materials. In case of IZTO nanoparticles, composition ratios of In, Zn and Sn is 8:1:1 were synthesized. Size of the synthesized IZTO nanoparticles were less than 10 nm, and specific surface areas were about $90m^2/g$ indicating particle sizes are very fine. Also, the IZTO nanoparticles were well crystallized with (222) preferred orientation despite it was synthesized at the lowered temperature of $300^{\circ}C$. Composition ratios of In, Zn and Sn were very uniform in accordance with those as designed. Meanwhile, Al was deposited onto glass by sputtering in a vacuum chamber for mesh architecture. The Al was well deposited onto the glass, and no pore was observed from the Al surface. The sheet resistance of Al on glass was about $0.3{\Omega}/{\square}$ with small deviation of $0.025{\Omega}/{\square}$, and adhesion was good on the glass substrate since no pelt-off part of Al was observed by tape test. If the Al mesh is combined with ink coated layer which is consistent of IZTO nanoparticles, it is expected that the good and reliable metal mesh architecture for TCE will be formed.

• 한국재료학회지
• /
• 제26권3호
• /
• pp.123-129
• /
• 2016

The morphology, crystal structure and size of aerosol nanoparticles generated by erosion of electrodes made of different materials (titanium, copper and aluminum) in a multi-spark discharge generator were investigated. The aerosol nanoparticle synthesis was carried out in air atmosphere at a capacitor stored energy of 6 J, a repetition rate of discharge of 0.5 Hz and a gas flow velocity of 5.4 m/s. The aerosol nanoparticles were generated in the form of oxides and had various morphologies: agglomerates of primary particles of $TiO_2$ and $Al_2O_3$ or aggregates of primary particles of $Cu_2O$. The average size of the primary nanoparticles ranged between 6.3 and 7.4 nm for the three substances studied. The average size of the agglomerates and aggregates varied in a wide interval from 24.6 nm for $Cu_2O$ to 46.1 nm for $Al_2O_3$.