• Journal of Environmental Science International
• /
• v.9 no.1
• /
• pp.95-99
• /
• 2000

Laboratory experiments were performed to investigate the effects of various factors on the phosphorus removal by electrolysis with aluminium electrodes. The efficiency of phosphorus removal increases with increasing of voltage applied, surface area of electrodes and electrolyte concentration, and decreasing of electrode distance. The phosphorus removal was not affected by the connection number of an electric circuit. The amount of aluminium ion eluted from electrodes according to Faraday's law was 4.47 mg and the A/P mole ratio was 2.14 at the electric current value of 20 mA.

• Journal of Environmental Health Sciences
• /
• v.25 no.3
• /
• pp.70-76
• /
• 1999

A laboratory experiment was performed to investigate the phosphorus removal using the activated sludge-electrolysis reactor which consisted of A$^2$/O system and aluminium electrodes as cathode and anode. In this system, the phosphorus was removed by aluminium ion, which was eluted from aluminiumelectrodes by electrolysis. In the batch experiments, when the current densities were 0.026, 0.052 and 0.08 A/dm$^2$, the phosphorus removal efficiencies for synthetic sewage were 66.4, 86.4 and 98.7% respectively. These results showed that the phosphorus removal efficiency increased with the increase of the current density. When the current values were 13, 26 and 40 mA respectively, the amounts of Al$^{3+}$ eluted from electrodes according to Faraday's law were 0.049, 0.07 and 0.12 g and Al/P mole ratio were 1.1, 2.0 and 3.41. In the continuous experiments, As hydraulic retention time(HRT) increased, COD and total nitrogen(T-N) removal efficiencies for domestic sewage increased. The average phosphorus removal rates of the activated sludge-electrolysis system were 97, 91, 80 and 80% at the HRT of 48, 24, 18 and 12 hours, respectively. Especially, the phosphorus removal rate in the activated sludge system with aluminium electrodes was higher than that in the system without aluminium electrodes.

• Electrical & Electronic Materials
• /
• v.9 no.8
• /
• pp.806-812
• /
• 1996

I-V characteristics of ground electrode fabricated using an aluminium scrap are presented. We fabricated several shapes of aluminium scraps and aluminium electrodes. The results show that the current of aluminium electrode increased linearly by the voltage increase. AC breakdown voltage of copper plate electrode was higher than that of aluminium electrode. AC breakdown current of aluminium electrode was higher than that of copper plate electrode. As applied voltage increased, grounding resistance of aluminum electrode decreased linearly.

• Journal of Electrochemical Science and Technology
• /
• v.12 no.1
• /
• pp.92-100
• /
• 2021

In this study, the use of waste food grade aluminium foil and mild steel as a sacrificial electrode in an electrocoagulation system was developed to remove reactive red 111 from wastewater. The effect of different parameters like pH, current density, electrode material, and different electrode configurations was investigated. Optimum operating conditions for maximum COD removal were determined as, 6 mA/㎠ current density and 30 min at 5 pH for aluminium foil and 7 pH for mild steel. Maximum COD reduction obtained at optimum conditions using monopolar 4 electrodes, monopolar 2 electrodes and bipolar electrode configuration were 96.5%, 89.3%, and 90.2% for Mild steel as a sacrificial electrode and 92.1%, 84.2%, and 88.6% for aluminium foil as a sacrificial electrode. The consumption of electrode and energy for both the electrodes of different configurations were calculated and compared. Using batch experimental data, a continuous-flow reactor was developed. Sludge analysis using Fourier Transform Infra-Red Spectroscopy (FTIR) analysis was done. Different adsorption kinetic models and isotherms were developed and it was found that pseudo second-order model and Langmuir isotherm fit best with the experimental data obtained.

• Proceedings of the KWS Conference
• /
• 1997.10a
• /
• pp.184-193
• /
• 1997

Aluminium and aluminium alloys have the high electrical and heat conductivity. It gives rise to difficulties for a choice of electrodes material for their contact electric welding. This paper describes the investigations performed to solve the above problem. The purpose of this investigation was to obtain dispersion-hardening alloys by the internal oxidation method, to optimize their contents and treatment modes, to produce electrodes of these alloys and to test them. The strengthing effect of alloys with oxide particles depends on their size stability at high temperatures. Despite of the fact, that oxides are the most stable of all the non-metallic phases their coagulation takes place. Based on the early results, we chose two types of alloys, first No. 1 Cu - 0,4%Al and second No. 2 Cu - 0,2%Be for production of electrodes. These alloys had not additional alloying elements. These alloys were prepared as 1 mm plates and flake-formed 200 m thick, and also No. 1 as a powder of size 100 mkm (received from Korea). The large samples for electrodes were produced by three methods : explosive welding method, dynamic one including the explosion compression of electrode blank and the quasi-dynamic method including the high-speed compression of dense briquest and the further hot extrusion of a rod.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.1
• /
• pp.46-49
• /
• 2016

A thin film transistor (TFT) has been fabricated using the amorphous 0.5 wt% Si doped zinc-tin-oxide (a-0.5 SZTO) with different electrodes made of either aluminium (Al) or titanium/aluminium(Ti/Al). Contact resistance and total channel resistance of a-0.5SZTO TFTs have been investigated and compared using the transmission line method (TLM). We measured the total resistance of 1.0×10² Ω/cm using Ti/Al electrodes. This result is due to Ti, which is a material known for its adhesion layer. We found that the Ti/Al electrode showed better contact characteristics between the channel and electrodes compared with that made of Al only. The former showed a less contact and total resistance. We achieved high performance of the TFTs characteristic, such as Vth of 2.6 V, field effect mobility of 20.1 cm² V⁻¹s⁻¹, S.S of 0.9 Vdecade⁻¹, and on/off current ratio of 9.7×10⁶ A. It was demonstrated that the Ti/Al electrodes improved performance of TFTs due to enhanced contact resistance.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1609-1611
• /
• 1997

We fabricated five type of electric double layer capacitor(EDLC) with extremely stable activated carbon as a positive and negative electrodes. The electrodes consisted of activated carbon and several different conductor layers on aluminium foil. Cyclic voltammogram of activated carbon electrodes at scan rate 5mV/sec was reversable redox reaction. The discharge capacity of activated carbon-KS 6 composite electrode was higher than that of activated carbon electrode without KS 6.

• Environmental Engineering Research
• /
• v.20 no.4
• /
• pp.392-396
• /
• 2015

This work aims to investigate the oily wastewater treatment by the electrocoagulation-flotation (ECF) and propose a mathematical model for the efficiency prediction. Cutting oil was used to prepare the synthetic oily wastewater with submicron droplet sizes. The chemical coagulation by aluminium sulfate was firstly tested following by the electrocoagulation-flotation with aluminium electrodes. Both processes gave the effective treatment performance with the efficiencies higher than 90%. However, the ECF consumed less aluminium dosage as well as produced less sludge, which were its advantage on the chemical coagulation. The performance of the ECF was found to be affected by the current density, oil concentration, and reaction time according to the analysis by the design of experiment (DOE). Finally, the prediction model was proposed by two approaches, including linear and logarithm function. The latter model gave more accuracy prediction results in terms of treatment efficiency and duration in the lag and stable stages.

• 전기의세계
• /
• v.29 no.11
• /
• pp.727-732
• /
• 1980

The main purpose of this paper is to study on the effect of contact state between metal-polymer interface in electrical conduction of polymeric materials under low field region. The electric conduction of polythylene (PE) sandwitched in between two gold (Au) electrodes was lower than that of PE Sandwitched in between two Aluminium (Al) electrodes under low external field. The discharge current of PE which have been treated by the high field application is also obtained some results under no external field. The obtained results can suggest that the material of electrode come to influence on the electrical conduction of polymeric materials and are important as a basis for analysing the data on TSC. It is also suggestive that results of observation must be considered in cases of insulation design of electrical machinery.

• Journal of the Korean Vacuum Society
• /
• v.9 no.4
• /
• pp.379-381
• /
• 2000

Organic materials have potential advantages to be utilized as semiconductors in field effect transistors and light emmiting diodes. Gold, Aluminium, Silver, Chromium and Indium are used by electrodes. Gold is ohmic contact and the others are schottky contact. In this study, Pentacene and various electrode materials were deposited by Organic Molecular Beam Deposition (OMBD) and vacuum evaporation respectively. Those films were photolithographically patterned for measurements. These devices showed no degration after a 15 days of storage in laboratory environment.