• Journal of the Korea Institute of Building Construction
• /
• v.16 no.4
• /
• pp.321-329
• /
• 2016

The use of ternary blended cement consisting of Portland cement, granulated blast-furnace slag (GGBFS) and fly ash has been on the rise to improve marine concrete structure's resistance to chloride attack. Therefore, this study attempted to investigate changes in chloride attack resistibility of concrete through NT Build 492-based chloride migration experiments and test of concrete's ability to resist chloride ion penetration under ASTM C 1202(KS F 2271) when 1.5-2.0% of alkali-sulfate activator (modified alkali sulfate type) was added to the ternary blended cement mixtures (40% ordinary Portland cement + 40% GGBFS + 20% fly ash). Then, the results found the followings: Even though the slump for the plain concrete slightly declined depending on the use of the alkali-sulfate activator, compressive strength from day 2 to day 7 improved by 17-42%. In addition, the coefficient from non-steady-state migration experiments for the plain concrete measured at day 28 decreased by 36-56% depending on the use of alkali-sulfate. Furthermore, total charge passed according to the test for electrical indication of concrete's ability to resist chloride ion penetration decreased by 33-62% at day 7 and by 31-48% at day 28. As confirmed in previous studies, reactivity in the GGBFS and fly ash improved because of alkali activation. As a result, concrete strength increased due to reduced total porosity.

• Journal of the Korea Institute of Building Construction
• /
• v.13 no.4
• /
• pp.391-399
• /
• 2013

For high strength concrete of 40~60 MPa, the effects on the early strength and concrete dry shrinkage properties replacing 60~80% of Ordinary Portland Cement with Blast Furnace Slag Powder and using the Alkali Activator (Modified Alkali Sulfate type) are considered in this study. 1% Alkali Activator to the binder, cumulative heat of hydration for 72 hours was increased approximately 45%, indicating that heat of hydration contributes to the early strength of concrete, and the slump flow of concrete decreased slightly by 3.7~6.6%, and the 3- and 7- strength was increased by 8~12%, which that the Alkali Activator (Modified Alkali Sulfate type) is effective for ensuring the early strength when manufacturing High Strength Concrete (60%) of Blast Furnace Slag Powder. Furthermore, the dry shrinkage test, both 40 MPa and 60 MPa specimens had level of length changes in order of BS40 > BS60 > BS60A > BS80A, and the use of the Alkali Activator somewhat improved resistance to dry shrinkage.

• Advances in concrete construction
• /
• v.10 no.3
• /
• pp.221-236
• /
• 2020

To reduce the CO₂ emissions associated with the manufacture of portland cement (PC), an efficient alternative like an alkali-activated binder (AAB) is the requirement of the industry. To promote the use of AAB in construction activities, a practically implementable mix proportion is required. Owing to the several raw ingredients of AAB concrete and their associated uncertainties, partial replacement of PC by AAB may be adopted instead of complete replacement as per industrial requirements. Hence, the present study aims to determine an optimal proportion for partial replacement of PC with AAB and recommend a technique for it based on site conditions. Three modes of partial replacement are followed: combining all the dry ingredients for AAB and PC followed by the addition of the requisite liquids (PAM); combining the PC and the AAB concrete in two horizontal layers (PAH); and two vertical layers (PAV). 28-day old specimens are exposed to 10% v/v solutions of HCl, H₂SO₄, and HNO₃ to evaluate changes in mechanical, physical, and microstructural characteristics through compressive strength, corrosion depth, and microscopy. Based on deterioration in strength and integrity, PAH or PAV can be adopted in absence of acid attack, whereas PAM is recommended in presence of acid attack.

• Journal of the Korean Applied Science and Technology
• /
• v.23 no.2
• /
• pp.169-176
• /
• 2006

Acrylic adhesives for automobiles protection were prepared by emulsion polymerization. Monomers used were n-butyl acrylate(BA), acrylonitrile (AN), butyl methacrylate(BMA), glycidyl methacrylate(GMA), and acrylic acid (AA). Emulsifiers used were sodium lauryl sulfate and polyoxyethylene lauryl ether, which are an anionic emulsifier and a nonionic emulsifier respectively. Potassium persulfate was used as an initiator and polyvinyl alcohol was used as a stabilizer. Emulsion polymerization was carried out in a semi-batch reactor at $70^{\circ}C$ and agitation speed was kept at 200 rpm. Water resistance, heat resistance, acid resistance, alkali resistance and smoke resistance were examined. As a result, when each 0.03 mole of GMA and AA was introduced, the adhesion properties and various above mentioned resistances of the prepared adhesives were satisfied the standard for automobiles.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.313-317
• /
• 2003

The study is the results of accelerated tests and the specimens, mortars, are submerged in a 5% sulfuric acid solution. The deterioration of specimens is followed up by investigating the change in weight and compressive strength of the specimens and techniques such as XRD and XRF are used to examine the chemical changes. Sulfuric acid is a very aggressive acid that reacts with the free lime [$Ca(OH)_2$] in the concrete forming gypsum($CaSO_{4}.2H_{2}O$). This reaction is associated with an increase in volume of the concrete, and the corroded surface becomes soft and white. The results showed that the OPC mortar caused an decrease in weight above 18% and strength loss about 57%. On the other hand, AASC(alkali-activated slag composites) did not cause any decrease in weight and in the case of strength caused an decrease below 10%. In addition, this mechanical results was verified to XRD and XRF.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.11a
• /
• pp.204-209
• /
• 1999

각종섬유를 연속섬유 보강재로 사용하는 경우, 일반적으로 수지를 매트릭스로 하여 봉재 형상(FRP rod)으로 제조하고있다. 성형된 섬유는 수지가 섬유의 보호재 역할을 하기 때문에, 콘크리트내의 알칼리와 절연되어 열화가능성이 작다고 고려된다. 그러나, 일반적으로 섬유를 둘러싼 수지는 그 두께가 수 {$mu}m$이하로 특히 얇고, 운반이나 보관시에 수지가 물리적 변형 및 자외선에 의한 열화가 일어날 가능성이 높다. 또 알칼리에 의하여 에스테르의 가수분해반응에 따른 폴리머의 부식 등, 수지에 알칼리의 침입을 완전히 막는 것이 불가능하게 여겨진다.

• Journal of the Korean Society of Safety
• /
• v.8 no.2
• /
• pp.30-38
• /
• 1993

To increase fire proofing characteristics of protective coating based on soluble alkali silicate, silicate coatings were studied on thermal properties, IR spectroscopy, solubility and intumescence. Intumescence and solubility of the samples were dependent on the strength of cationic cross-links between polysilicate particles. The degree of intumescence and solubility decrease K-silicate > Na-silicate > Li-silicate in the order. Especially Si$_2$O$_{5}$ $^{-2}$ crystalline regions were found to exist in Potassium silicate sample. Mixture of two kinds of silicate, for example, Lithium silicate when added to sodium silicate or potassium silicate was find to significantly reduce efflorescence and increase water resistance. This appears to be a result of stronger crosslinking between polysilicate particles by the small lithium cation.

• Journal of the Korean Applied Science and Technology
• /
• v.15 no.1
• /
• pp.35-45
• /
• 1998

Chitin/chitosan be known as biodegradable natural polymer. However, commercial use of chitin has been limited due to highly resistance to chemicals and the absense of proper solvents. Therefore, we was studied that chitin was prepared by the application of Hackman's method from Protunus trituberculatus shells. And another viscosity chitosan were prepared from chitin which were deacetylated under various concentration of alkali, reaction time and temperature by the application of Mima's method. And crosslinked chitin/chitosan was preparaed from chitin/chitosan with crosslink agent followed by crosslinkage. The major parameters for chitosan manufacturing methods were found to be concentration of alkali solution, reaction time and temperature etc. The effects of these parameters on chitin, another viscosity(molecular weight) chitosan and crosslinked chitin/chitosan were investigated by various analysis apparatus.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.10 no.5
• /
• pp.9-15
• /
• 2010

Recently, the high-compressive strength concrete where the use is extending was weak in fire because of spalling that was occurring with rise of internal vapor pressure by high temperature. For preventing spalling of high-strength concrete in fire, Organic fibers have been using in concrete generally. By melting of organic fibers in concrete in fire, the internal moistures of concrete moves quickly to the outside, and so, preventing of spalling of high-strength concrete. But this method will be able to prevent the spalling of high-strength concrete, but makes the decrease of the concrete strength after fire. This study make a comparison between properties of preventing of spalling and remaining compressive strength of concrete using intumescence Alkali-Silicates fire-resistant material and that of concrete with organic fibers. Using organic fibers for preventing of spalling of concrete are P.P and Nylon fibers, and anti-fire intumescence material for protection of concrete surface is alkali-silicate materials. Fire resistance test executed as long as 3 hr under the flame temperature $1,200^{\circ}C$ over. In the case of concrete with P.P fibers, don't occurred the spalling, but the remaining compressive strength will not be able to measure, the concrete using intumescence Alkali-Silicates system fire-resistant material is not only preventing of the spalling but also the remaining compressive strength maintained until the maximum 96%.

• Journal of the Korean Ceramic Society
• /
• v.52 no.4
• /
• pp.253-263
• /
• 2015

Ordinary Portland cement is a widely favored construction material because of its good strength and durability and its reasonable price; however, spalling behaviour during fire exposure can be a serious risk that can lead to strength degradation or collapse of a building. Geopolymers, which can be synthesized by mixing aluminosilicate source materials such as metakaolin and fly ash, and alkali activators, are resistant to fire. Because the chemical composition of geopolymers controls the properties of the geopolyers, geopolymers with various Si:Al ratios were synthesized and evaluated as fire resistant construction materials. Rejected fly ash generated from a power plant was quantitatively analyzed and mixed with alkali activators to produce geopolymers having Si:Al ratios of 1.5, 2.0, and 3.5. Compressive strength of the geopolymers was measured at 28 days before and after heating at $900^{\circ}C$. Geopolymers having an Si:Al ratio of 1.5 presented the best fire resistance, with a 44% increase of strength from 29 MPa to 41 MPa after heating. This material also showed the least expansion-shrinkage characteristics. Geopolymer mortar developed no spalling and presented more than a 2 h fire resistance rating at $1,050^{\circ}C$ during the fire testing, with a cold side temperature of $74^{\circ}C$. Geopolymers have high potential as a fire resistant construction material in terms of their increased strength after exposure to fire.