• Tribology and Lubricants
• /
• 제39권1호
• /
• pp.13-20
• /
• 2023

Large drill bits may face high hardness ore and high working pressure when working. To optimize the use effect of large drill bits and prolong the use time, it is necessary to add a layer of pressure-resistant, wear-resistant, and low-friction coating on the surface of the drill bit. In this study, CoCrNiAlTi high-entropy alloy coatings and CoCrNiAlTi (70 wt%)-TiC (30 wt%) composite coatings are successfully prepared on Q235 steel by plasma spraying. The CoCrNiAlTi (70 wt%)-TiC (30 wt%) coating consists of FCC solid solution and a small amount of TiC phase. The effect of TiC on the composition phase, microhardness, and elastic modulus of HEA coating is studied by X-ray diffractometer (XRD) and microhardness tester. The effect of TiC on the friction and wear properties of HEA coatings is investigated using a wear tester. By improving the process parameters, the metallurgical bonding between the coating and the substrate is well combined, and a coating without pores and cracks is obtained. The experimental results confirm that the microhardness, elastic modulus, and wear resistance of CoCrNiAlTi-TiC composite coating are better, and the friction coefficient is lower.

• Advances in Energy Research
• /
• 제2권2호
• /
• pp.97-104
• /
• 2014

A co-spray deposition technique has been developed to bypass a fundamental limitation in the conventional spray deposition technique, i.e., the deposition of metal oxides from incompatible precursors in the starting solution. With this technique, ZnO films codoped with F and Al have been successfully synthesized, in which F is incompatible with Al. Two starting solutions were prepared and co-sprayed through two separate spray heads. One solution contained only the F precursor, $NH_4F$. The second solution contained the Zn and Al precursors, $Zn(O_2CCH_3)_2$ and $AlCl_3$. The deposition was carried out at $500^{\circ}C$ on soda-lime glass in air. A minimum sheet resistance, $55.4{\Omega}/{\square}$, was obtained for Al and F codoped ZnO films after vacuum annealing at $400^{\circ}C$, which was lower than singly-doped ZnO with either Al or F. The transmittance for the codoped ZnO samples was above 90% in the visible range. This co-spray deposition technique provides a simple and cost-effective way to synthesize metal oxides from incompatible precursors with improved properties for photovoltaic applications.

• Journal of Magnetics
• /
• 제19권1호
• /
• pp.55-58
• /
• 2014

We have synthesized ferromagnetic ${\tau}$-phase $Mn_{54}Al_{46}/{\alpha}$-phase $Fe_{65}Co_{35}$ composite by annealing a mixture of paramagnetic ${\varepsilon}$-phase $Mn_{54}Al_{46}$ and ferromagnetic ${\alpha}$-phase $Fe_{65}Co_{35}$ particles at $650^{\circ}C$. The volume fraction ($f_h$) of hard ${\tau}$-phase $Mn_{54}Al_{46}$ of the composite was varied from 0 to 1. During the annealing, magnetic phase transformation occurred from paramagnetic ${\varepsilon}$-phase to ferromagnetic ${\tau}$-phase $Mn_{54}Al_{46}$. The magnetization and coercivity of the composite monotonically decreased and increased, respectively, as the $f_h$ increased. These results are in good agreement with our proposed composition dependent coercivity and modified magnetization equations.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2000년도 특별강연 및 춘계학술발표대회 개요집
• /
• pp.71-74
• /
• 2000

자기 구속 균열 시험법인 Tapered 시편 균열 시험법을 이용하여 Al-Mg 합금의 CW $CO_2$ 레이저 용접시 Mg 함량 변화에 따른 고온균열감수성 변화를 조사하였다. Mg 함량 1.9wt.%에서 최대균열감수성을 나타내고 있으며 이보다 Mg 함량이 증가하거나 감소하면 고온균열 감수성이 감소한다. 용접금속 결정립 크기 또한 고온균열감수성과 관련이 있으며 Mg 함량이 증가할수록 결정립이 미세화되며, 1.9wt.%Mg 이상에서 결정립이 미세화될수륵 고온균열 감수성 이 감소한다.

• 한국자기학회지
• /
• 제15권1호
• /
• pp.17-20
• /
• 2005

RF magnetron sputtering 법으로 Co-Fe-Al-O계 박막을 상온에서 제작하여 산소분압에 따른 포화자화, 보자력, 이방성자계, 고주파에서의 투자율(1 GHz)을 조사하였다. 최적조건인 4%의 산소분압에서 제조한 $Co_{69.9}Fe_{20.5}A_{14.4O_{5.2}$ 박막은 포화자속밀도 18.1kG, 보자력 0.82 Oe, 이방성자계 24 Oe, 실효 투자율(1 GHz) 1,024의 우수한 연자성을 나타내었다. Co-Fe-Al-OrP 박막의 전기비저항은 산소분압이 560.7 ${\mu}{\omega}cm$ 이었다. 따라서 약 560.7${\mu}{\omega}cm$의 높은 전기바저항과 24 Oe의 높은 이방성 자계 때문에 $Co_{69.9}Fe_{20.5}A_{14.4O_{5.2}$ 박막이 고주파에서 우수한 연자기적 성질을 가지는 것으로 판단된다.

• 대한조선학회논문집
• /
• 제51권6호
• /
• pp.548-555
• /
• 2014

As a considerable, experimental approach, an Auto-carriage type of $CO_2$ welding machine and a MIG(Metal Inert Gas) welding robot under inert gas atmosphere were utilized in order to realize Al 5083 welding applied to hull and relevant components of green Al leisure ships. This study aims at investigating the effect of welding conditions(current, voltage, welding speed, etc) on thermal deformation that occurs as welding operation and tensile characteristics after welding, by using Al 5083, non-ferrous material, applied to manufacturing of co-environmental Al leisure ships. With respect to welding condition to minimize the thermal deformation, 150A and 16V at the wire-feed rate of 6mm/sec were acquired in the process of welding Al 5083 through an auto carriage type of $CO_2$ welding feeder. As to tensile characteristics of Al 5083 welding through a MIG welding robot, most of tensile specimens showed the fracture behavior on HAZ(Heat Affected Zone) located at the area joined with weld metal, except for some cases. Especially, for the case of the Al specimen with 5mm thickness, 284.62MPa of tensile strength and 11.41% of elongation were obtained as an actual allowable tensile stress-strain value. Mostly, after acquiring the optimum welding condition, the relevant welding data and technical requirements might be provided for actual welding operation site and welding procedure specification(WPS).

• 한국대기환경학회지
• /
• 제3권1호
• /
• pp.1-12
• /
• 1987

A series of supported sulfided Ni-W/$\gamma-Al_2O_3$ and Co-W/$\gamma-Al_2O_3$ catalysts with different nickel and cobalt contents were studied in the hydrodenitrogenation of pyridine dissolved in n-heptane. The ranges of experimental conditions were at the temperatures between 453 and 753 K, and the pressures between 30 and 50 Bar. The catalytic activities with different nickel and cobalt contents were shown to be maximum at Ni/Ni+W = 0.2 - 0.3, Co/Co+W = 0.3 - 0.4. Pyridine conversion increased with pressure and temperature and the step of piperidine formation was found to be irreversible. The reaction orders in Ni-W/$\gamma-Al_2O_3$ and Co-W/$\gamma-Al_2O_3$ catalysts were the first with respect to pyridine and reaction rate constants decreased with increase of initial pyridine concentration and their activation energies were 12.98 and 9.23 kcal/mol, respectively.

• Journal of Electrochemical Science and Technology
• /
• 제7권4호
• /
• pp.263-268
• /
• 2016

This study describes the effect of coating the $Li[Ni_{0.8}Co_{0.15}Al_{0.05}]O_2$ cathode surface with a homogeneous carbon layer produced by carbonization of polyvinylidene fluoride (PVDF) as a novel organic source. The phase integrity of the above cathode was not affected by the carbon coating, whereas its rate capability and cycling performance were enhanced. Similarly, the cathode thermal stability was also improved after coating, which additionally protected the cathode surface against the reactive electrolyte containing hydrofluoric acid (HF). The results show that coating the $Li[Ni_{0.8}Co_{0.15}Al_{0.05}]O_2$ cathode with carbon using the PVDF precursor is an effective approach to enhance its electrochemical properties.

• 한국자기학회지
• /
• 제11권3호
• /
• pp.109-113
• /
• 2001

Presently, an inductor adapted at MMIC (Monolithic Microwave Integrated Circuit) which is used for cellular phone or PHS operates at quasi-microwave range over 800 MHz. However, a W-CDMA (Wideband Code Division Multiple Access) will use about 2 GHz range. Therefore magnetic film device should be compatible up to 2 GHz. We have deposited Co-Pd-Al-O system film using rf sputtering method which is expected up to 2 GHz, and investigated the effect of Pd content and magnetic field annealing. When Pd composition is 19%, Hk was 118 Oe, and ${\mu}$′showed flat frequency characteristics up to 1.5 GHz. The Q factor (=${\mu}$′/${\mu}$") was 23.3 at 1 GHz, 6.7 at 1.5 GHz and 1.5 at 2 GHz, respectively. Resonance frequency was 2 GHz. Therefore Co-Pd-Al-O thin film could be used at over 1 GHz, and also expected as an inductor material for wide band CDMA type cellular phone.

• Corrosion Science and Technology
• /
• 제12권3호
• /
• pp.119-124
• /
• 2013

Nano-multilayered, crystalline AlTiSiN thin films were deposited on WC-TiC-Co substrates by the cathodic arc plasma deposition. The deposited film consisted of wurtzite-type AlN, NaCl-type TiN, and tetragonal $Ti_2N$ phases. Their oxidation characteristics were studied at 800 and $900^{\circ}C$ for up to 20 h in air. The WC-TiC-Co oxidized fast with large weight gains. By contrast, the AlTiSiN film displayed superior oxidation resistance, due mainly to formation of the ${\alpha}-Al_2O_3$-rich surface oxide layer, below which an ($Al_2O_3$, $TiO_2$, $SiO_2$)-intermixed scale existed. Their oxidation progressed primarily by the outward diffusion of nitrogen, combined with the inward transport of oxygen that gradually reacted with Al, Ti, and Si in the film.