• 한국결정성장학회지
• /
• 제24권3호
• /
• pp.106-110
• /
• 2014

Atomic layer deposition(ALD)을 이용하여 $Al_2O_3$ 박막을 형성하고 이에 대한 패시베이션 특성에 대한 연구를 수행하였다. ALD로 증착된 $Al_2O_3$ 박막은 $400^{\circ}C$ 5분간 후속 열처리 공정 후에도 $Al_2O_3$ - 실리콘 계면 반응 없이 비정질 상태를 유지할 만큼 구조적으로 안정한 특성을 나타내었다. 후속 열처리 후 $Al_2O_3$ 박막의 패시베이션 특성이 향상되었으며, 이는 field effective 패시베이션과 화학적 패시베이션 효과가 동시에 상승에 기인하는 것으로 판단된다. $Al_2O_3$ 박막의 음고정 전하를 정량적으로 평가하기 위해서 후속 열처리 공정을 거친 $Al_2O_3$ 박막을 이용하여 metal-oxide-semiconductor(MOS) 소자를 제작하고 capacitance-voltage(C-V) 분석을 수행하였다. C-V 결과로부터 추출된 flatband voltage($V_{FB}$)와 equivalent oxide thickness(EOT)의 관계식을 통하여 $Al_2O_3$ 박막의 고정음전하는 $2.5{\times}10^{12}cm^{-2}$로 계산되었으며, 이는 본 연구에서 제시된 $Al_2O_3$ 박막 공정이 N-type 실리콘 태양전지의 패시베이션 공정에 응용 가능하다는 것을 의미한다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.395-398
• /
• 2000

Reactive radio frequency (RF)magnetron sputter with incident angle has been used to deposit AlN thin film on a crystalline Si substrate. (002)Preferred orientation of AlN thin film has been obtained at low sputtering pressure. Also it has been shown that depostion rate of AIN thin film is affected by fraction Ar and $N_2$ partial pressure. But substrate temperature didn't affect depostion rate of AIN thin film . As sputtering pressure increased preferred orientation degraded. The internal stress changed from tensile stress to compressive stress as fraction of $N_2$ partial pressure increased. At low nitrogen partial pressure cermet$^{[1]}$ AIN thin film is obtained.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2001년도 제21회 학술발표회 초록집
• /
• pp.66-66
• /
• 2001

• E2M - 전기 전자와 첨단 소재
• /
• 제8권1호
• /
• pp.13-20
• /
• 1995

To develope a high precision TiAIN thin film resistor, TiAIN films were deposited on A1$_{2}$03 substrates by reactive planar magnetron cosputtering from Ti and Al targets in an Ar-N$_{2}$ atmosphere. The characteristics of the TiAIN thin film were controlled by changing of the R.F. power on Ti and Al targets, and the N$_{2}$ partial pressure. The high precision TiAIN thin film resistor with TCR(Temperature Coefficient of Resistance) of less than 10ppm/.deg. C was obtained under the R.F. power condition of 160(w)/240(w) to Ti and Al targets at the N$_{2}$ partial pressure of 7*10$^{-5}$ Torr. The composition of these films were investigated by XRD, SEM and EDS.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.1333-1334
• /
• 2007

Al thin film was the most popular electrode in semiconductor and flat panel display world, because of its electrical conductivity, selectivity and easy to apply to thin film. However, Al thin films were not good to use on the bottom electrode about the crystalline growth of inorganic compound materials such as ZnO, AlN and GaN, because of its surface roughness and melting points. In this paper, we investigated Ar plasma surface treatment of Al thin film to enhance the surface roughness and electrical conductivity using the reactive ion etching system. Several process conditions such as RF power, working pressure and process time were controlled. In results, the surface roughness showed $15.53\;{\AA}$ when RF power was 100 W, working pressure was 50 mTorr and process time was 10 min. Also, we tried to deposit ZnO thin films on the each Al thin films, the upper conditions showed the best crystalline characteristics by x-ray diffraction.

• 전기학회논문지
• /
• 제56권8호
• /
• pp.1455-1460
• /
• 2007

This paper reports the piezoelectric microspeakers that are audible in open air with high quality piezoelectric AlN thin film deposited onto Mo/Ti electrode. This successful achievement, compared to the previous results, is followed by manipulating two material properties: the one is to use a compressively stressed silicon nitride film as a supporting diaphragm (even tensile stressed, around +20 MPa) and the another is to use high quality AlN thin film with compressive residual stress (less than -100 MPa). With these materials, the Sound Pressure Level (SPL) of the fabricated micro speakers shows more than 60 dB from 100 Hz to 15 kHz and the highest SPL is about 100 dB at 9.3 kHz with 20 Vpeak-to-peak sinusoidal input and with 10 mm distances from the fabricated micro speakers to the reference microphone (B&K Type 2669 & 4192L).

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.118-118
• /
• 2011

The Nano-Floating Gate Memory(NFGM) devices with ZnO:Cu thin film embedded in Al2O3 and AlOx-SAOL were fabricated and the electrical characteristics were evaluated. To further improve the scaling and to increase the program/erase speed, the high-k dielectric with a large barrier height such as Al2O3 can also act alternatively as a blocking layer for high-speed flash memory device application. The Al2O3 layer and AlOx-SAOL were deposited by MLD system and ZnO:Cu films were deposited by ALD system. The tunneling layer which is consisted of AlOx-SAOL were sequentially deposited at $100^{\circ}C$. The floating gate is consisted of ZnO films, which are doped with copper. The floating gate of ZnO:Cu films was used for charge trap. The same as tunneling layer, floating gate were sequentially deposited at $100^{\circ}C$. By using ALD process, we could control the proportion of Cu doping in charge trap layer and observe the memory characteristic of Cu doping ratio. Also, we could control and observe the memory property which is followed by tunneling layer thickness. The thickness of ZnO:Cu films was measured by Transmission Electron Microscopy. XPS analysis was performed to determine the composition of the ZnO:Cu film deposited by ALD process. A significant threshold voltage shift of fabricated floating gate memory devices was obtained due to the charging effects of ZnO:Cu films and the memory windows was about 13V. The feasibility of ZnO:Cu films deposited between Al2O3 and AlOx-SAOL for NFGM device application was also showed. We applied our ZnO:Cu memory to thin film transistor and evaluate the electrical property. The structure of our memory thin film transistor is consisted of all organic-inorganic hybrid structure. Then, we expect that our film could be applied to high-performance flexible device.----못찾겠음......

• 한국전기전자재료학회논문지
• /
• 제21권5호
• /
• pp.458-462
• /
• 2008

In this paper, we investigated the (002) preferred orientation and morphology characteristics of AlN thin film by using reactive rf sputtering. Additionally, AlN thin films grown in the range from 150 to 300 W were studied under room temperature without substrate heating and post annealing. Sputtered AlN thin films were well grown on Si substrates and the (002) main peak in XRD patterns showed the highest intensity at 300 W with $0.25^{\circ}$ degree of full width at half-maximum (FWHM). As increased RF power, the surface roughness was increased from 1.0 to 3.4 nm. In Fourier transformation infrared spectroscopy (FTIR), $A_1$ (TO) and $E_1$ (TO) mode closed to AlN thin film confirmed the changes with increasing the intensity rate. From these results, we could confirm a chance of the growth of AlN thin film by only low temperature.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제36회 동계학술대회 초록집
• /
• pp.132.2-132.2
• /
• 2009

• Journal of Electrical Engineering and Technology
• /
• 제2권4호
• /
• pp.525-531
• /
• 2007

Ni(75 wt.%)-Cr(20 wt.%)-Al(3 wt.%)-Mn(4 wt.%)-Si(1 wt.%) alloy thin films were prepared using the DC magnetron sputtering process by varying the sputtering conditions such as power, pressure, substrate temperature, and post-deposition annealing temperature in order to fabricate a precision thin film resistor. For all the thin film resistors, sheet resistance, temperature coefficient of resistance (TCR), and crystallinity were analyzed and the effects of sputtering conditions on their properties were also investigated. The oxygen content and TCR of Ni-Cr-Al-Mn-Si resistors were decreased by increasing the sputtering pressure. Their sheet resistance, TCR, and crystallinity were enhanced by elevating the substrate temperature. In addition, the annealing of the resistor thin films in air at a temperature higher than $300^{\circ}C$ lead to a remarkable rise in their sheet resistance and TCR. This may be attributed to the improved formation of NiO layer on the surface of the resistor thin film at an elevated temperature.