• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.2
• /
• pp.206-215
• /
• 1994

A method for simulating general characteristics and temperature characteristics of discharging SCR of the capacitor discharge impulse magnetizer-magnetizing fixture system using SPICE is presented. This method has been developed which can aid the design, understanding and inexpensive, time-saving of magnetizing circuit. As the detailed characteristic of magnetizing circuit can be obtained, the efficient design of the magntizing circuit which produce desired magnet will be possible using our SPICE modeling. Especially, computation of the temperature rise of discharging SCR is very important since it gives some indication of thermal characteristic of discharging circuit. It is implemented on a 486 personal computer, and the modeling results are checked against experimental measures. The experimental results have been achived using 305[V] and 607[V] charging voltage, low-energy capacitor discharge impulse magnetizer-magnetizing fixture of air cleaner DC motor.

• Journal of the Korean Society of Combustion
• /
• v.14 no.4
• /
• pp.48-53
• /
• 2009

This paper describes the forced flame response in a turbulent premixed gas turbine combustor. The fuel was premixed with the air upstream of a choked inlet to avoid equivalence ratio fluctuations. To impose the inlet flow velocity, a siren type modulation device was developed using an AC motor, rotating and static plates. Measurements were made of the velocity fluctuation in the nozzle using hot wire anemometry and of the heat release fluctuation in the combustor using chemiluminescence emission. The test results showed that flame length as well as geometry was strongly dependent upon modulation frequency in addition to operating conditions such as inlet velocity. Convection delay time between the velocity perturbation and heat release fluctuations was calculated using phase information of the transfer function, which agreed well with the results of flame length measurements. Also, basic characteristics of the flame nonlinear response shown in the current test conditions were introduced.

• Proceedings of the Safety Management and Science Conference
• /
• 2006.11a
• /
• pp.361-365
• /
• 2006

Air pollution problem has been one of the most urgent global environmental problems since UN Framework Convention on Climate Change accepted in Rio Conference, 1992. International environmental regulations of global community to reduce the green house gases have Influenced the domestic environmental policies. Recently, various policy have been made to cope with foreign environment restrction and active supports for development of related technology have been carried out in our government confrontation strategy still leaves much to be desired. In this paper, government confrontation program to climate agreement, counter strategies in motor and also electrics, electronics industries are investigated and discussed.

• Proceedings of the KIEE Conference
• /
• 2005.04a
• /
• pp.117-119
• /
• 2005

This parer presents the application of response surface methodology (RSM) to design optimization for two types of synchronous reluctance motors (SynRMs) one has 12 slots with distributed winding, and the other has 6 slots with concentrated winding, to improve the ratio between torque ripple and average torque. The usefulness of RSM in optimization problem of SynRM is verified as compared with the results of finite element analysis. In the end, the optimized two SynRMs are compared with SynRM currently used in air-conditioning compressor in connection with torque performance and loss.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.22 no.5
• /
• pp.373-381
• /
• 2017

The electric vehicle market has increased rapidly in recent years. Established global automakers have announced that electric cars will be developed and distributed. Furthermore, current electric cars are not merely breezes, instead, they are the mainstream of automobiles. However, high prices, short mileage, and long charge times are the main obstacles to the spread of electric vehicles. To solve these problems, the competition for technology development for the expansion of electric vehicles worldwide intensifies because of the improvements in mileage, price reduction, and expansion of charging infrastructure. In this paper, the trends in the development of key technologies for electric vehicles in overseas markets and the present strategic goals for the development of key technologies for electric vehicles in Korea will be identified.

• Proceedings of the KIEE Conference
• /
• 1999.07a
• /
• pp.194-196
• /
• 1999

This paper verifies that DSPSRM having the rotor pole of "ㅓ" shape has a radial and axial flux distribution, and analyzes the flux density distribution of each direction using 3D FEM.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.981-983
• /
• 2000

Linear induction motors have static and dynamic end effects due to its finite core length, so that per-phase impedances are asymmetric and the air gap flux distribution is distorted. Because of these points the d-q equivalent circuit model considering both end effects has not been exactly completed. So this paper proposes a characteristic analysis method considering both static and dynamic end effect of the LIM. This method is to utilize asymmetric d-q equivalent circuit model with dynamic end effect coefficient. As a result, it is shown that the simulation results have a good agreement with experimental ones.

• 한국전산유체공학회:학술대회논문집
• /
• 2003.08a
• /
• pp.165-170
• /
• 2003

Centrifugal blowers are widely used for air handling units in industry applications. The blower has a centrifugal impeller and a scroll casing including a driving component such as an electric motor. The impeller takes forward or backward blades to induce flows into the blower. Comprehensive investigation according to the two kinds of blades is systematically carried out for a guidance of design. It is observed that flow rate of the blower with forward blades is larger than that of the system with backward blades. The reason is due to larger velocity from the rotating forward blades and the tendency is validated by a parallel experiment with a wind tunnel. Numerical analysis for the system shows detail information inside the blades and the casing. A series of figures to show the flow details offers deep understanding of a centrifugal blower with different blades.

• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.185-191
• /
• 2006

Auxiliary power supply developed by domestic technology has very important function that not only effect on main power converter & inverter system, traction motor and train control system which are related to performance of train, but also influence on power supply for HVAC(Heat, Ventilation, Air-conditioning) and lighting device which are related to comfort of passengers. This paper shows characteristic test results of auxiliary power supply such as working condition and performance, which is associated with velocity of train, operating mode and surrounding equipment, through test running. Also it shows the results deduced from comparison analysis between designed data and manufactory test data as measuring in put voltage of auxiliary power supply. And, it propose a modification of design parameter for stabilizing operation and improving reliability.

• Journal of the Korean Society for Railway
• /
• v.10 no.1 s.38
• /
• pp.84-87
• /
• 2007

Auxiliary power supply developed by domestic technology has very important function that not only effect on main power converter & inverter system, traction motor and train control system which are related to performance of train, but also influence on power supply for HVAC(Heat, Ventilation, Air-conditioning) and lighting device which are related to comfort of passengers. This paper shows characteristic test results of auxiliary power supply such as working condition and performance, which is associated with velocity of train, operating mode and surrounding equipment, through test running. And, it propose a modification of design parameter for stabilizing operation and improving reliability.