• 설비공학논문집
• /
• 제7권4호
• /
• pp.633-641
• /
• 1995

The effect of the gap width on conjugate heat transfer in the cylindrical annulus for an insulated tube has been studied numerically by the finite difference method. The parameters considered here are the Rayleigh number, Ra, the dimensionless insulated wall thickness, $W/D_i$ and the dimensionless gap width, S/W. As S/W increases, the mean wall temperature increases at the inside wall of annulus and decreases at the outside walls of annulus and the insulated tube at $S/W{\leq}0.5$, and then slightly increases at $Re=10^4$, $W/D_i=1.47$. The heat transfer rate decreases at $S/W{\leq}0.5$ and then increases apparently as S/W increases at $Re=10^4$, W/Df=1.47. Therefore, it is considered that $$S/W{\sim_=}0.5$$ is the optimum gap width for the effect of insulation at $Re=10^4$, $W/D_f=1.47$.

• 전자공학회논문지A
• /
• 제33A권12호
• /
• pp.53-58
• /
• 1996

In this paper, a simple fabrication technique of an air-bridge for interconnection of isolated electrodes of microwave active and passive devices and MMIC's is proposed. The proposed air-bridge proceses are mainly combinations of thermal evaporation, positive photoresist and image reversal processes for easy lift-off of up to 2.0 .mu.m thick metal. According to the resutls of air-birdge processes, it is confirmed that air-gap and thickness of theair-bridge are about 3.5.mu.m, and 2.0.mu.m, respectively. And it is also possible to make the fine air-bridge with widths of 5~60.mu.m and post-intervals of 25~200.mu.m withot collapse. finally, GaAs power MESFET's and rectangular spiral inductors are fabricatd and measured in order to confirm of feasibility of the proposed air-bridge processes. The MAG of the fabricated power MESFET's is 10dB at 10GHz, and the inductance of the (200.mu. * 6 turns) rectangular spiral inductors 4.5 nH inX-band.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.62-64
• /
• 2001

In this paper, we present the fabrication and performance of tunable capacitors with various structural geometry of plates. Experimental devices have been fabricated using Cu-electroplating techniques and standard MEMS techniques. In particular, the thickness of electroplated Cu is designed below $0.5{\mu}m$ for lower actuation voltage. The fabricated tunable capacitors has been tested from $OV{\sim}42V$ and achieves a tuning ratio of $46%{\sim}64.2%$.

• 유공압시스템학회논문집
• /
• 제7권4호
• /
• pp.44-49
• /
• 2010

This paper represents solenoid design of control valve for incline angle control in variable compressor. Some theoretical and numerical analysis were performed to analyse solenoid and compared with experimental results. Maxwell program was used for numerical analysis. Through redesigns of housing body, plunger, core, and disk in control valve, the needed force was gotten. Reduction of core groove and housing body air-gap had a large influence on magnetic force. But increasing of disk thickness had little effect on magnetic force. Control valve efficiency could be improved through solenoid redesign.

• 전자공학회논문지
• /
• 제51권3호
• /
• pp.202-209
• /
• 2014

본 논문에서는 원형편파 패치안테나에 상부덮개를 여러 층으로 적층함으로써 안테나 성능에 미치는 영향을 분석하였다. 지금까지 원형편파 패치안테나를 설계하기 위해서는 주로 단층의 상부덮개를 적용하거나, 여러 층으로 구성된 하나의 상부덮개를 적용하였고, 성능 분석시 안테나 축비를 거의 고려하지 않았다. 먼저, 상부덮개와 패치안테나 간의 공기층 높이에 의한 중심주파수의 변화를 분석하였다. 공기층 높이가 적을 때는 중심주파수가 낮은 쪽으로 천이하였고, $005{\lambda}_0$의 공기층 높이에서는 주파수 천이가 거의 없었다. 다음은 최적의 공기층 높이를 적용하여 상부덮개의 층수를 증가하면서 안테나 성능을 분석하였다. 상부덮개의 층수가 증가하면서 안테나 이득은 비례적으로 증가하지만, 안테나 축비는 점차적으로 악화되었다. 또한, 상부덮개의 유전체 두께가 증가할수록 안테나 이득은 증가하지만 안테나 축비는 급격히 악화되었다. 결과적으로 안테나 축비를 3dB 이내로 유지하면서 상부덮개의 층수를 확장하여 다양한 이득을 얻을 수 있는 안테나 설계가 가능함을 확인하였다.

• 한국의학물리학회지:의학물리
• /
• 제27권4호
• /
• pp.196-202
• /
• 2016

We aim to develop the breast bolus by using a 3D printer to minimize the air-gap, and compare it to commercial bolus used for patients undergoing reconstruction in breast cancer. The bolus-shaped region of interests (ROIs) were contoured at the surface of the intensity-modulated radiation therapy (IMRT) thorax phantom with 5 mm thickness, after which the digital imaging and communications in mdicine (DICOM)-RT structure file was acquired. The intensity-modulated radiation therapy (Tomo-IMRT) and direct mode (Tomo-Direct) using the Tomotherapy were established. The 13 point doses were measured by optically stimulated luminescence (OSLD) dosimetry. The measurement data was analyzed to quantitatively evaluate the applicability of 3D bolus. The percentage change of mean measured dose between the commercial bolus and 3D-bolus was 2.3% and 0.7% for the Tomo-direct and Tomo-IMRT, respectively. For air-gap, range of the commercial bolus was from 0.8 cm to 1.5 cm at the periphery of the right breast. In contrast, the 3D-bolus have occurred the air-gap (i.e., 0 cm). The 3D-bolus for radiation therapy reduces the air-gap on irregular body surface that believed to help in accurate and precise radiation therapy due to better property of adhesion.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.462-463
• /
• 2007

SF6 widely used as insulating gas is rising as the environment problem. For decreasing this greenhouse gas, electrical breakdown characteristics of composite insulation composed of epoxy resins with N2, air are studied in non-uniform field. The gap of needle to plane was 3mm, 5mm. The pressure of air, nitrogen was varied within the range of 0.1~0.6MPa. The thickness of a needle is 1mm and the curvature radius of the end of needle is 100um. The diameter of a plane made of the stainless steel is 50mm. As a result of the experiment, the breakdown voltage is increased about 3 times when epoxy resins is composited. The thickness of epoxy resins filled opposite to electrode concentrated electric field weakly influences on breakdown voltage.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 B
• /
• pp.892-894
• /
• 1995

This paper deals with developmeant and application of coating thickness control system in hot dip galvanizing process. According to the line conditions, such as line speed, strip size and target coating weight, a predictive preset model sets the initial oprating conditions. Referring the zine coating informations from the gauge, mean coating value controller adjusts the chamber pressure and horizontal distance between strip and air knife, while coating deviation controller adjusts the lip gap profile of the air knife. All adaptive gains are interactively calculated by numeric models based on the theoretical analysis. The operating result with this system effectively reduces the coating deviation in transverse direction as well as in longitudinal direction.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.1084-1087
• /
• 2002

The guard-ring type 3-terminal parallel plate electrodes proposed by ASTM D 150-81 and IEC 250 have been widely used for measurement of dielectric constants of solid dielectrics. However the method using this electrodes causes many uncertainty associated with the measurement errors of the diameter of the guarded electrode. the gap between guarded and guard-ring electrode. the distance of two active electrodes(the thickness of specimen), the roughness and contamination of surface of electrode and specimen. close adherence grade of electrode and specimen. In this paper. a new electrode system of cross capacitance type based on Thompson-Lampard theorem is designed and is employed for the measurement of dielectric constant. The results of simulation of guard-ring electrode and cross capacitance electrode using FEM program show that distance measurement between two electrodes in guard-ring electrode produces large uncertainty. on the other hand this effect in cross capacitance electrode is negligible. Furthermore. the air gap effects in the cross capacitance electrode is 5.6 times less sensitive than that in guard-ring electrode by assuming air gap of $50{\mu}m$.

• 한국정밀공학회지
• /
• 제18권2호
• /
• pp.119-125
• /
• 2001

This paper presents an experimental study on active control of self-excited vibration for a high speed turbomachinery. In order to suppress the self-excited vibration, it is necessary to actively control the air film pressure or the air film thickness. In this study, active pads are used to control the air film thickness. Active pads are supported by pivots containing piezoelectric actuators and their radial position can be actively controlled by applying voltage to the actuators. The transfer characteristics from actuator inputs to shaft vibration outputs are experimentally investigated. In a tilting-pad gas bearing (TPGB), a shaft is supported by the pressurized air film. Four gap sensors were used to measure the vibration of the shaft and PID was used in the feedback control of the shaft vibration. The experimental results show that the self-excited vibration of the rotor can be effectively suppressed if the PID controller gains are properly chosen. As a result we find that the feedback control is effective for suppressing the self-excited vibration of a rotor system using stack-type PZT actuators.