• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.08a
• /
• pp.35-38
• /
• 2003

In this paper, we investigated the electric and acoustic properties of piezoelectric composites, which were fabricated using polymer and piezoelectric ceramics, when the volume fraction of PZT varies. Practically, the shrinkage rate of polymer is an important factor in ultrasonic transducer fabrication. When 10 wt% filler A was added into polymer(Epofix), the lowest shrinkage was resulted. The electromechanical coupling factor($k_t$) of the fabricated piezoelectric composites showed its highest when the volume fraction PZT was 0.6. It decreased if the volume fraction was higher than the value. The relative permittivity and acoustic impedance of piezoelectric composites decreased linearly when PZT volume fraction was decreased. The lowest acoustic impedance was 3.2 when the volume fraction of PZT was 0.2.

• The Journal of the Acoustical Society of Korea
• /
• v.24 no.7
• /
• pp.379-386
• /
• 2005

Among various kinds of hearing aids which have been developed so far. the conventional air conduction hearing aids have some problems such as the acoustic distortion, an howling effect due to acoustic feedback. Another type of hearing aid. the cochlear implant system can be applied to the profound imparied person. However. it shows the disadvantage that there is no possibility of recovery of the acoustic organ such as ossicle. On the other hand. the implantable middle ear heaving device directly vibratos the ossicular chain and has better sound qualify. good cosmetics for appearance. and wide frequency responses so that it can overcome the defects or the conventional hearing aids. In this paper, a mathematical modeling and a momentum equation derivation of the DET has been performed. For the optimization of the structure dimension generating maximal vibrating force of the DET. the computer simulation using a finite element analysis (FEA) software has been performed. Also. the vibrating transducer has been designed to make the frequency characteristics or the transducer be similar to those of the normal middle ear. Through the experimental results, the measured vibration characteristics of the DET has been evaluated to verify the performance for the application to implantable middle ear hearing devices.

• The Journal of the Acoustical Society of Korea
• /
• v.14 no.2E
• /
• pp.73-86
• /
• 1995

The transducer section of the forward-looking ultrasound imaging catheter (FLUIC) consists of a circular piezoelectric element as a vibrator and a conical acoustic mirror as a perfect reflector. A small diameter piezoelectric transducer element is mounted on the side of a catheter's rotating shaft. The unique design of FLUIC provides the capability to form a two-dimensional image of a cross-section of vessel in front of the catheter, which is lacking in the present generation of intravascular ultrasound (IVUS) transducers, as well as a conventional side view image. The mirror configuration for the transducer section of the FLUIC is designed using an approximated ray tracing techniques. The diffraction transfer function approach [1] developed for the field prediction from primary sources is generalized and extended to predict the secondary diffraction characterstics from an acoustic mirror. The extended model is verified by simulation and experiment through a simple plane reflector and employed to analyzed the field characteristics of a FLUIC.

• The Journal of the Acoustical Society of Korea
• /
• v.25 no.4
• /
• pp.164-171
• /
• 2006

If the velocities of longitudinal, transverse and leaky surface acoustic waves in an isotropic material are given, the elastic constants and density of the material can be deduced analytically. Those velocities have been measured using three ultrasonic transducers with different vibrational modes so far. In this paper a line-focusing PVDF transducer with divided electrodes was newly proposed and designed for measuring approximate velocities of the three waves. The measurement method established in this study for each waves using the transducer was applied to several isotropic materials including fused quartz. The elastic stiffness constants and densities of the materials were calculated using the measured velocities, and the accuracies were discussed. It was shown that the obtained results are in good accord with the reference values.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.5 no.2
• /
• pp.42-48
• /
• 1986

Electromagnetic - Acoustic Transducers for the inspection of tubes were developed using permanent magnets and induction coils. The propagation velocity of ultrasonic waves in a tude wall was measured by the transducers. The position of a flaw in a tube and the relative size of flaws with different size were measured.

• Journal of KSNVE
• /
• v.6 no.5
• /
• pp.645-652
• /
• 1996

In this paper an identification method is presented to obtain the equivalent electric circuit model of a wideband underwater acoustic piezoelectric vibrator. Unknown parameters involved in the equivalent circuit are indentified using the measured electrical admittances in air. The proposed method is applied to an example transducer. The validity of equivalent circuit model is demonstrated by the comparison between the experimental measurements and analytical calculations of TVR(transmitting voltage response) in water.

• The Journal of the Acoustical Society of Korea
• /
• v.39 no.2
• /
• pp.87-97
• /
• 2020

In this paper, the design of piezoelectric Micro-machined Ultrasonic Transducer (pMUT) for wideband ultrasonic radiation in air was investigated. One of the methods to achieve wide frequency bandwidth in single device is modeling the transducer to multi-resonance system. The new pMUT was designed as a multi-resonance system with the addition of a suitable acoustic structure to the front and back of a thin film structure. A new pMUT consisting of thin film parts, radiation parts, and packaging parts is designed with a Lumped Parameter Model (L.P.M). Finally, it was validated as a Finite Element Method (FEM) simulation. The final designed pMUT achieved a frequency band of 102 kHz ~ 132 kHz (-3 dB).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.05a
• /
• pp.22-25
• /
• 1995

In this paper, the physical characteristics of piezoelectric transducer which generates acoustic weve at microwave frequency were theoretically analized. We found that increasing electrode thickness is showed large distorthion on bandwidth. ZnO thin film were desposited by RF magnetron sputtering method. considering the sputtering parameters. Thickness of the desposited ZnO was 3.9 $\mu\textrm{m}$. In this experiment, we get that resistivity is 12.196${\times}$109 [cm$\Omega$], that resonance frequency is 827.47MHz Measuring insertion loss, we ascertained to possibility of transducer application for microwave frequency.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.12
• /
• pp.2349-2351
• /
• 2010

Photo Acoustic Tomography (PAT) is a hybrid imaging modality which combines high contrast of optical imaging and spatial resolution of ultrasound imaging, thus it is suitable to image biological tissue noninvasively. Laser-induced photoacoustic signals were measured from a sample by means of an unfocused ultrasound transducer, then PAT image was reconstructed based on a universal back-projection algorithm. To evaluate the feasibility of our system, phantom test was performed, consequently, the PAT images obtained using our system showed highly analogous shape and volume with those of the phantom. This result demonstrated that our system can provide a powerful tool for imaging the substructure of biological tissue in non-invasive manner.

• The Journal of the Acoustical Society of Korea
• /
• v.18 no.1E
• /
• pp.20-26
• /
• 1999

Although the radiation impedance of a transducer with a regular square surface has been studied by many researchers, the formulas are still very complicated, which results in long computation time and low accuracy. In this paper, we propose a new algorithm for the calculation of acoustic radiation impedance in which the regular square vibrating surface of a transducer is divided into small elements and duplicate calculations are eliminated in the process of calculating mutual effects of the elements. Using this algorithm, shorter computation time and higher accuracy of results can be obtained. As a demonstration, the self and the mutual radiation impedance of transducers with a regular square surface are calculated and the accuracy of the results is evaluated.