• Journal of Sensor Science and Technology
• /
• v.21 no.6
• /
• pp.408-412
• /
• 2012

An in-line dispersive delay line (DDL) demands low and controllable reflectivity of the reflectors, especially if the surface acoustic wave (SAW) propagates all the way along the reflecting structure. The metal reflectors are usually too strong and introduce too much attenuation in such a device. The proposed solution of this problem is to spatially separate the acoustic channels for different frequencies with the help of Fan-shaped Transducers (FIDT) and to use narrow open metal reflectors to reduce reflectivity. Special arrangement of FIDT is performed to use 180-deg. reflection of the SAW. Narrow open metal strips with a metallisation ratio of the order of 20% are used as reflectors with small and controllable reflectivity. Reflectivity of such strips is estimated both theoretically and experimentally. Experimental performance of the proposed DDL is presented.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.625-628
• /
• 2005

Silencers are extensively used for reducing noise in an exhaust system of internal combustion Engine and fluid machineries. The prediction and measurement of the transmission loss as the acoustic performance of silencers are important in early design stage. In the measurement of transmission loss, the semi-anechoic terminations are general used for reducing unwanted effects by reflecting wave. However it is very hard to remove reflecting wave perfectly. So the research about the error made by reflecting wave is important. The analysis about errors made by reflections and modification techniques are proposed. For an application example, the diesel particulate filter (DPF) is chosen. The transmission loss of DPF is measured with and without considerations of reflecting wave.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2001.05a
• /
• pp.363-368
• /
• 2001

Because of rapid damping of light and electromagnetic wave, acoustic wave has been widely used for underwater communication. However, the propagation of the acoustic wave is highly dependent on the environment such as water properties(temperature, pressure, salinity), bottom and surface conditions, etc.. This paper deals with the surface reflection effect on the wave propagation in the underwater anechoic basin in KRISO. Both theortical and experimental approaches are performed and the results are compared.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.5
• /
• pp.738-745
• /
• 2009

Underwater acoustic communication has multipath error because of reflection by sea-level and sea-bottom. The multipath of underwater channel causes receive signal to make error floor. In this paper, we propose the underwater communication system using various channel coding schemes such as RS coding, convolutional code, turbo code and concatenated code for overcoming the multipath effect in underwater channel. As shown in simulation results, characteristic of multipath error is similar to that of random error. So interleaver has not effect on error correcting. For correcting of error floor by multipath, it is necessary to use strong channel codes like turbo code. Turbo code is one of the iterative codes. And the performance of concatenated codes including RS code has better performance than using singular channel codes.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.727-732
• /
• 2014

The goal is to find the position of the sound source with the TRM at reflections and refractions environment. The Fermat's principle applied to the ray tracing method are expected to follow the acoustic path in order to obtain acoustic distance and transmittance to. Utilizing them in the TRM was confirmed rear reflectance affect on estimated position, resolution and side lobe. And the TRM performance were superior to one of the beam forming techniques.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.12
• /
• pp.1039-1044
• /
• 2002

Film Bulk Acoustic Resonator (FBAR) using thin piezoelectric films can be made as monolithic integrated devices with compatibility to semiconductor process, leading to small size, low cost and high Q RF circuit elements with wide applications in communications area. This paper presents an MMIC compatible suspended FBAR using SOI micromachining. It is possible to make a single crystal silicon membrane using a SOI wafer In fabricating active devices, SOI wafer offers advantage which removes the substrate loss. FBAR was made on the 12㎛ silicon membrane. Electrode and Piezoelectric materials were deposited by RF magnetron sputter. The maximum resonance frequency of FBAR was shown at 2.5GHz range. The reflection loss, K$^2$$\_$eff/, Q$\_$serise/ and Q$\_$parallel/ in that frequency were 1.5dB, 2.29%, 220 and 160, respectively.

• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.2
• /
• pp.21-32
• /
• 2004

The non-cavitating noise of underwater propeller is considered numerically in this study. The main purpose is to analyze non-cavitating noise from underwater propellers in various operating conditions with different configurations. Noise is predicted by using time-domain acoustic analogy, boundary element method, and computational hydro-acoustics. The flow field is analyzed with potential-based panel method, and then time-dependant pressure data are used as the input for Focus Williams-Hawkings formulation to predict far field acoustics. Furthermore, boundary element method and computational hydro-acoustics are also considered to investigate duct propeller and ducted multi-stage propeller to consider the reflection and diffraction of sound waves. With this methodology, noise intensity and directivity of each noise sources could be well analyzed.

• The Journal of Information Technology
• /
• v.5 no.2
• /
• pp.69-80
• /
• 2002

Conventionally, we have used an acoustic microscope at single operating frequency. The resolution and quality of the measured images are determined by transducer of the microscope. In this paper, we have studied Vertical Resolution Enhancement with Acoustic Reflection Microscope using combining bases of support for SFR(Spatial Frequency Response). Increased Vertical resolution can be obtained by taking three-dimensional images at more that one frequency and numerically combining the results. As results of the experiment, we could get enhanced images with the rate of contrast in proportion to the changing rate of depth.

• International Journal of Ocean System Engineering
• /
• v.3 no.3
• /
• pp.158-163
• /
• 2013

The acoustic target strength (TS) is one of the most important parameters for a submarine's stealth design. Because modem submarines are larger than their predecessors, TS must be managed at each design stage in order to reduce it. To predict the TS of a submarine, TASTRAN R1 was developed based on a Kirchhoff approximation in a high-frequency range. This program can present TS values that include multi-bounce effect in the exterior and interior of the structure by combining geometric optics (GO) and physical optics (PO) methods, anechoic coating effect by using the reflection coefficient, and response time pattern for a detected target. In this paper, TS calculations for a submarine model with the above effects are simulated by using this developed program, and the TS results are discussed.

• Journal of Sensor Science and Technology
• /
• v.27 no.6
• /
• pp.374-379
• /
• 2018

The piezocomposite transducer is widely used because it is highly efficient in transforming electric energy into mechanical energy, and its frequency range is broader than that of other types of ultrasound transducers. A general piezocomposite transducer is composed of an acoustic lens, impedance matching layers, piezoelectric materials, and backing layers. When an input voltage is applied to a piezoelectric material as an active material, it generates sound waves while vibrating. At that time, an impedance matching layer helps the sound waves to propagate forward while reducing the impedance mismatch that may occur at the interface between the active material and its front material. The impedance mismatch has a negative effect on the signal of an ultrasound transducer; thus, it is important to design a matching layer to overcome the issue. In this study, an optimized feature of a matching layer with gradient properties is studied. An objective function is defined to minimize both the average and the deviation of the reflection coefficients that are functions of the frequencies. As a result, an improvement in the signal characteristics with respect to the sensitivity and bandwidth is reported.