• Transactions of the Korean hydrogen and new energy society
• /
• v.31 no.6
• /
• pp.499-508
• /
• 2020

Whilst vehicle-to-every (V2X) is still at a research and development phase, we are nearing the point when this technology could begin to enter in commercial mass markets. However, this transition is unlikely to happen until a number of issues have been resolved which currently hinder the developing of V2X technology and its capacity to provide value to end-users and other actors. This roadmap has set out plan for how these issues may be overcome, based on eight key goals that the automotive industry, network operators and policy makers should aim to achieve. Suggestions for near-term activities that may be carried out towards meeting these goals have also been identified.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.4
• /
• pp.313-320
• /
• 2011

Multi-axle driving vehicles that are used in special environments require high driving performance, steering performance, and stability. Among these vehicles, 6WS/6WD vehicles with middle wheels have structural safety by distributing the load and reducing the pitch angle during rapid acceleration and braking. 6WS/6WD vehicles are favored for military use in off road operations because of their high maneuverability and mobility on extreme terrains and obstacles. 6WD vehicles that using in-wheel motor can generate the independent wheel torque without other mechanical parts. Conventional vehicles, however, cannot generate an opposite driving force at each side wheel. Using an independent steering and driving system, six-wheel vehicles can show better performance than conventional vehicles. Using of independent steering and driving system, the 6 wheel vehicle can improve a performance better than conventional vehicle. This vehicle enhances the maneuverability under low speed and the stability at high speed. This paper describes an independent 6WS/6WD vehicle, consists of three parts; Vehicle Model, Control Algorithm for 6WS/6WD and Simulation. First, vehicle model is application of TruckSim software for 6WS and 6WD. Second, control algorithm describes the optimum tire force distribution method in view of energy saving. Last is simulation and verification.

• Information and Communications Magazine
• /
• v.34 no.6
• /
• pp.11-19
• /
• 2017

V2X(Vehicle to Everything)는 차량 간 통신(Vehicle-to-Vehicle), 차량과 인프라 간 통신(Vehicle-to-Infrastructure), 차량과 보행자 간의 통신(Vehicle-to-Pedestrians) 등 운전 중 도로 인프라 및 다른 차량과 통신하면서 교통상황 등의 정보를 교환하거나 공유하는 기술을 말한다. V2X는 IT 기술의 발달과 여러 연구기관들의 연구개발 강화로 인해 'Connected/Smart car' 나아가 완전한 자율주행차를 구현하기 위해 빠르게 진화하고 있다. 이러한 V2X 시장이 향후 10년 간 급속한 확대가 전망되면서, 국내외 통신업체와 제조업 및 산학연은 자동차와 정보통신, 에너지, 서비스 산업을 융합한 스마트자동차 산업을 신성장 동력으로 하여 기술개발에 노력을 가속화하고 있다. 이에 본고에서는 V2X 차량 통신 기술의 주요선진국 기술개발 동향과 현 수준을 알아본다.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.2
• /
• pp.79-85
• /
• 2007

The skid-steering method that applied a number of mobile robot currently is very effective in narrow area. But it contains several problems of its natural properties, slip, occurred by different direction between vehicle's driving and wheel's rotary. From this thesis we want to suggest suitable structure of $6{\times}6$ skid steering wheeled vehicle and method of driving by analyzing the behavior of $6{\times}6$ skid-steered wheeled vehicle by engineering analytical method

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.6_spc
• /
• pp.644-650
• /
• 2016

Track maintenance works based on track geometry recordings are essential to enhance the safety and comfort of railway transportation. Usually, the track irregularity has been measured by a special inspection trains which all were imported from abroad. Because the inspection train speed is limited under 160 km/h, it takes a long time to inspect railways and there is difficulty in daytime operation. To solve this problem, we started to develop a track geometry measuring system (TGMS) with measurement speed up to 300 km/h which can be installed in commercial vehicles such as HEMU-430X. In this paper, we introduce a newly developed inertial TGMS and propose two inertial navigation system (INS) algorithms (method A, B) for measuring track geometry. In order to investigate advantage and disadvantage of each algorithm, we performed vibration test of the TGMS, which was simulated by 6-axis shaking table. Through the vibration test, we analyzed the influence of vehicle vibration on the TGMS which will be installed on bogie frame. To the vibration test, two methods satisfied the required accuracy of track geometry measurement under the level of the actual vehicle vibration of HEMU-430X train. Theoretically, method A is sensitive to vehicle vibration than method B. However, HEMU-430X's bogie vibration frequency range is out of interest range of measurement system. Therefore, method A can also apply the HEMU-430X train.

• Journal of Korean Society for Atmospheric Environment
• /
• v.31 no.6
• /
• pp.562-572
• /
• 2015

$NO_x$ emissions from diesel vehicles have been regarded as a main cause of high $NO_2$ concentration in metropolitan area. Recent studies have shown that the on-road $NO_x$ emissions of diesel vehicles are quite higher than the emission limits specified with the pre-defined test method for emission certification. To reduce air pollutants effectively, the discrepancy of emissions in certification and real-driving conditions should be tackled. In this study, the real-driving emissions have been estimated with portable emission measurement system (PEMS). The results of this study have shown that the on-road $NO_x$ emissions from diesel vehicles have been decreased as the introduction of stricter emission regulation, EURO-6, but additional reduction should be still required and robust technologies should be applied to control $NO_x$ in real-driving conditions. RDE-LDV (Real Driving Emission - Light Duty Vehicles) test method being developed in the European Union can represent excessive on-road $NO_x$ emissions of diesel vehicles as applied emission technologies and can be a solution to remove discrepant $NO_x$ emissions between certification and Korean real-driving conditions. Among the $NO_x$ reduction technologies for EURO-6 diesel vehicles, selective catalytic reduction (SCR) system has shown the better performance than lean $NO_x$ trap (LNT) system to control on-road $NO_x$ emissions. Implementing RDE-LDV will require vehicle manufacturers to adopt the more effective $NO_x$ reduction technology in real driving conditions.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.18 no.6
• /
• pp.251-261
• /
• 2019

The importance of autonomous driving systems that utilize V2X services such as V2V(Vehicle to Vehicle) and V2I(Vehicle to Infrastructure) for safer and more comfortable driving is increasing with the recent development of autonomous vehicles. Partly autonomous vehicles based on environmental sensors have limitations for predicting and determining areas beyond the recognition distance of the mounted sensors and in response to atypical objects that are difficult to detect. Therefore, it is important to utilize the V2X service to improve the limit of sensor detection performance and to make driving safer and more comfortable. However, there may be an accident risk of autonomous vehicles due to incorrect information provided by V2X. Thus, the application of technology to prevent this needs to be considered. In this pater, we used the ISO-26262 Part3 Process and performed HARA (Hazard Analysis and Risk Assessment) to derive the risk sources of autonomous vehicles due to V2I malfunctions by using the communication between vehicles and infrastructure among V2X. We also developed ASIL ratings based on the simulations and real vehicle tests of the malfunctions of major cases of usnig V2I.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.7
• /
• pp.599-605
• /
• 2017

For an unmanned vehicle to be driven on the off-road terrain, it is necessary to consider the vehicle's stability. This paper suggests a path tracking controller for simulation of real-time vehicle stability analysis. The path tracking controller uses the preview distance to track the given trajectory. The disturbance moment is estimated using the yaw moment observer, and this information is used for compensation in the yaw moment control. On a curved path, the vehicle's desired velocity is determined from the curvature of the path. Because the vehicle is equipped with six independent motor driven wheels, the driving torques are distributed on all the wheels. The effectiveness of the path tracking controller is verified using ADAMS/MATLAB co-simulation.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.6
• /
• pp.72-86
• /
• 2019

SpaceX is currently leading the global launch market with the successful launch and recovery of Falcon 9 v1.2 Block 5. SpaceX developed Merlin engine, a kerosene gas generator engine, and continuously upgraded the engine from Falcon 1 to Falcon Heavy to increase payload weight. SpaceX suffered a lot of failures early on, but with the help of NASA, it was possible to overcome many crises and develop vehicles. In addition, it successfully developed reusable vehicles, which drastically reduced operating costs. Subsequent launch vehicles in Korea also need to be developed with reference to SpaceX's development strategy.

• Journal of Aerospace System Engineering
• /
• v.13 no.6
• /
• pp.36-42
• /
• 2019

This research illustrates how the simulation environment for operating the simultaneous man/unmanned aerial vehicle teaming is constructed. X-Plane program, HILS for the ducted fan aircraft (unmanned) and CTLS (manned aircraft) with communication devices are interfaced to simulate the basic co-operational flight. The X-plane and HILS can allow operators to experience the maned and unmanned aircraft operation in the airspace on the ground in turn they can perform various simulated missions in advance before the actual flight. For the test purpose, the data link between man/unmanned aircraft and ground control station is examined using C Band and UHF radio channels by the manned aircraft.