• Progress in Medical Physics
• /
• v.20 no.4
• /
• pp.308-316
• /
• 2009

To achieve the accurate evaluation of given absorbed dose from output dose of linear accelerator photon beam through investigate the characteristics of LiF:Mg,Cu,P TLD powder. This experimental TL phosphor is performed with a commercial LiF:Mg,Cu,P powder (Supplied by PTW) and TL reader (LTM, France). The TLD was exposed to 6 MV X rays of linear accelerator photon beam with range 15 to 800 cGy in blind dose at two hospitals. The dose evaluation of TLD was through the experimental algorithms which were dose dependency, dose rate dependency, fading and powder weight dependency. The glow curve has shown the three peaks which are 110, 183 and 232 degrees of heating temperature and the main dosimetric peak showed highest TL response at 232 high temperature. In this experiments, the LiF:Mg,Cu,P phosphor has shown the 2.5 eV of electron trap energy with a second order. This experiments guided the dose evaluation accuracy is within 1% +2.58% of discrepancy. The TLD powder of LiF:Mg,Cu,P was analyzed to dosimetric characterists of electron captured energy and order by glow shape, and dose-TL response curve guided the accuracy within 1.0+2.58% of output dose discrepancy.

• Journal of Sensor Science and Technology
• /
• v.11 no.4
• /
• pp.247-253
• /
• 2002

For fabrication of the pyroelectric IR sensor $(Pb,La)TiO_3(PLT)$/$LiTaO_3$/(LTO)/PLT ferroelectric thin films was deposited by rf magnetron sputtering followed by rapid thermal annealing and the crystallinity as a function of annealing temperature and time was investigated. Permittivity and dielectric loss factor of ferroelectric thin films as a function of c-axis preffered orientation was measured. Also pyroelectric coefficient of ferroelectric thin films with largest c-axis preffered orientation was measured and obtain figure of merit of voltage response($F_V$) and detectivity($F_D$). In this case $F_V$, $F_D$ was $5.63{\times}10^{-10}\;C{\cdot}cm/J$, $1.98{\times}10^{-8}\;C{\cdot}cm/J$, respectively.

• Transactions on Electrical and Electronic Materials
• /
• v.6 no.1
• /
• pp.25-28
• /
• 2005

We have investigated the effects of hole-injection buffer layer in organic light-emitting diodes using poly(3,4-ethylenedioxythiophene):poly(stylenesulfonate)(PEDOT:PSS) in a device structure of $ITO/PEDOT:PSS/TPD/Alq_{3}/cathode$. Polymer PEDOT:PSS buffer layer was made by spin casting method. Current-voltage, luminance-voltage characteristics and efficiency of device were measured at room temperature with a variation of cathode materials; Al, LiF/Al, LiAl, and Ca/Al. The device with LiF/Al cathode shows an improvement of external quantum efficiency approximately by a factor of ten compared to that of Al cathode only device. Our observation shows that cathode is important in improving the efficiency of the organic light-emitting diodes.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.2
• /
• pp.1211-1215
• /
• 2014

We developed a new $Rb_2LiCeCl_6$ scintillator and determined the scintillation and thermoluminescence properties of the scintillator. The emission spectrum of $Rb_2LiCeCl$ is located in the range of 350 ~ 410 nm, peaking at 368 nm and 378 nm, due to the 4f ${\rightarrow}$ 5d transition of $Ce^{3+}$ ions. The fluorescence decay time of the crystal is composed two components. The fast component is 71 ns (85%) and the slow component is 405 ns (15%) of the crystal. The after-glow is caused by the electron and hole traps in the crystal lattice. We determined physical parameters of the traps in the crystal. The determined activation energy(E), kinetic order(m) and frequency factor(s) of the trap are 0.75 eV, 1.48 and $3.0{\times}10^8s^{-1}$, respectively.

• Asian-Australasian Journal of Animal Sciences
• /
• v.26 no.6
• /
• pp.896-904
• /
• 2013

Cattle breeds have a striking effect on milk, including milk composition and technological characteristics. This study aims to compare milk composition, acidification activity, viscosity, milk dispersion system stability and casein molecular weight among three buffalo breeds in China. The technological characteristics of milk produced by three cattle breeds of river buffalo (Murrah), crossbreed 1st generation ($F_1$), crossbreed multiple generation ($F_H$, $H{\geq}3$) buffaloes were investigated. Cattle breeds showed evident effect on milk protein, fat and total solids content, but little effect on most of buffalo casein molecular weight. Milk fat, protein content and the viscosity of buffalo milk from river buffalo were lower than those of $F_1$ and $F_H$, so was the buffer capacity. The viscosity was negatively correlated to temperature and concentration. Results of stability coefficient showed that milk dispersion system had the best dynamic stability characteristics under pH 6.6 and 6 times dilution, while zeta potential of Murrah milk was slightly higher than that of hybrid offspring ($F_1$, $F_H$). SDS-PAGE results showed that buffalo ${\alpha}_s$-casein had a slightly faster mobility than standard ${\alpha}_s$-casein; while buffalo ${\beta}$-casein showed a slightly slower mobility than standard ${\beta}$-casein. There is no clear differences in molecular weight of ${\alpha}_s$-, ${\beta}$-, and ${\kappa}$-casein among Murrah, $F_1$ and $F_H$.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.10
• /
• pp.3303-3310
• /
• 2012

Two single crystals of fully dehydrated partially $Li^+$-exchanged zeolite X were prepared by the exchange of Na-X, $Na_{92}Si_{100}Al_{92}O_{384}$ (Si/Al = 1.09), with $Li^+$ using aqueous 0.1 M $LiNO_3$ at 293 (crystal 1) and 333 K(crystal 2), followed by vacuum dehydration at 623 K and $1{\times}10^{-6}$ Torr for 2 days. Their structures were determined by single-crystal synchrotron X-ray diffraction techniques in the cubic space group $Fd{\overline{3}}$ at 100(1) K. Their structures were refined using all intensities to the final error indices (using the 1281 and 883 reflections for which ($F_o$ > $4{\sigma}(F_o)$) $R_1/R_2$ = 0.075/0.244 and 0.074/0.223 for crystals 1 and 2, respectively. Their compositions are seen to be ${\mid}Li_{86}Na_6{\mid}[Si_{100}Al_{92}O_{384}]$-FAU and ${\mid}Li_{87}Na_5{\mid}[Si_{100}Al_{92}O_{384}]$-FAU, respectively. In crystal 1, 17 $Li^+$ ions per unit cell are at site I', 15 another site I', 30 at site II, and the remaining 16 at site III; 2 $Na^+$ ions are at site II and the remaining 4 at site III'. In crystal 2, 32 and 30 $Li^+$ ions per unit cell fill sites I' and II, respectively, and the remaining 25 at site III'; 2 and 3 $Na^+$ ions are found at sites II and III', respectively. The extent of $Li^+$ exchange increases slightly with increasing ion exchange temperature from 93% to 95%.

• Journal of the Korean Chemical Society
• /
• v.57 no.1
• /
• pp.12-19
• /
• 2013

The single-crystal structure of fully dehydrated partially $Li^+$-exchanged zeolite Y, ${\mid}Li_{50}Na_{25}{\mid}[Si_{117}Al_{75}O_{384}]$-FAU, was determined by single-crystal synchrotron X-ray diffraction techniques in the cubic space group $Fd\bar{3}m$ at 100(1) K. Ion exchange was accomplished by flowing stream of 0.1 M aqueous $LiNO_3$ for 2 days at 293 K, followed by vacuum dehydration at 623 K and $1{\times}10^{-6}$ Torr for 2 days. The structure was refined using all intensities to the final error indices (using only the 801 reflections with ($F_o$ > $4{\sigma}(F_o)$) $R_1/R_2=0.043/0.140$. The 50 $Li^+$ ions per unit cell are found at three different crystallographic sites. The 19 $Li^+$ ions occupy at site I' in the sodalite cavity: the $Li^+$ ions are recessed 0.30 ${\AA}$ into the sodalite cavity from their 3-oxygens plane (Li-O = 1.926(5) ${\AA}$ and $O-Li-O=117.7(3)^{\circ}$). The 20 $Li^+$ ions are found at site II in the supercage, being recessed 0.23 ${\AA}$ into the supercage (Li-O = 2.038(5) ${\AA}$ and $O-Li-O=118.7(3)^{\circ}$). Site III' positions are occupied by 11 $Li^+$ ions: these $Li^+$ ions bind strongly to one oxygen atom (Li-O = 2.00(8) ${\AA}$). About 25 $Na^+$ ions per unit cell are found at four different crystallographic sites: 4 $Na^+$ ions are at site I, 5 at site I', 12 at site II, and the remaining 4 at site III'.

• Journal of the Microelectronics and Packaging Society
• /
• v.3 no.2
• /
• pp.27-38
• /
• 1996

Lithium fluorhectorite 결정상을 함유한 glass ceramics 분말의 형성과 제조된 glass ceramics 분말을 이용한 저온 소결기판의 특성평가를 하였다. Li2O-MgO-MgF2-SiO2 계 유 리로 핵형성 및 결정 성장을 실시하여 lithium fluorhectorite 결정상을 지닌 glass ceramics 를 제조하였다. 유리시편의 핵형성 온도는 46$0^{\circ}C$였고 결정성장온도는 600, 640, 110$0^{\circ}C$에서 나타났다. $600^{\circ}C$에서의 결정상으 Li2.4LiSi4O10F2가 나타났다. Li2.4Mg8LiSi4와 Li2.8Mg0.6SiO4은 lithium fluorhectorite 결정상으로 되기 위한 중간상임을 확인할수 있었다. 64$0^{\circ}C$에서 열처리 후 110$0^{\circ}C$에서 재열처리하여 형성된 결정은 lithium fluorhectorite 와 tridymite가 최종 결정 상으로 나타났다. 이것은 수중에서 water swelling 현상에 의하여 분말화할 수 있었다, 기판 제조용 slurry를 제조하기 위해 glass ceramics 분말에 Al2O3분말을 0,25,50wt%로 혼합한것 과 glass ceramics 분말에 potashborosilica-te glass 분말을 15, 30, 45, 60 wt% 로 배합하 여 doctor blade 법으로 green sheet를 제조하였다. green sheet 는 950~150$0^{\circ}C$로소성하여 기판의 특성을 평가하였다. 겉보기 기공율은 3.06~19,14%이었고, 전기적 특성으로 유전상수 는 3~5(100KHz)를 나타내었다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.11
• /
• pp.717-721
• /
• 2017

We studied the performance enhancement of organic light-emitting diodes (OLEDs) using 2,3,5,6-fluoro-7,7,8,8-tetracyanoquinodimethane ($F_4-TCNQ$) as the hole-transport layer. To investigate how $F_4-TCNQ$ affects the device performance, we fabricated a reference device in an ITO (170 nm)/TPD(40 nm)/$Alq_3$(60 nm)/LiF(0.5 nm)/Al(100 nm) structure. Several types of test devices were manufactured by either doping the $F_4-TCNQ$ in the TPD layer or forming a separate $F_4-TCNQ$ layer between the ITO anode and TPD layer. N,N'-diphenyl-N,N'-di(m-tolyl)-benzidine (TPD), tri(8-hydroxyquinoline) aluminum ($Alq_3$), and $F_4-TCNQ$ layers were formed by thermal evaporation at a pressure of $10_{-6}$ torr. The deposition rate was $1.0-1.5{\AA}/s$ for TPD and $Alq_3$. The LiF was subsequently thermally evaporated at a deposition rate of $0.2{\AA}/s$. The performance of the OLEDs was considered with respect to the turn-on voltage, luminance, and current efficiency. It was found that the use of $F_4-TCNQ$ in OLEDs enhances the performance of the device. In particular, the use of a separate layer of $F_4-TCNQ$ realizes better device performance than other types of OLEDs.

• Polymer(Korea)
• /
• v.31 no.6
• /
• pp.497-504
• /
• 2007

We have prepared the dinuclear half-sandwich CGC(constrained geometry catalyst) with polymethylene bridge $[Zr(({\eta}^5\;:\;{\eta}^1-C_9H_5SiMe_2NCMe_3)Me_2)_2\;[(CH_2)_n]$ [n=6(4), 9(5), 12(6)] by treating 2 equivalents of MeLi with the corresponding dichlorides compounds. To study the catalytic behavior of the dinuclear catalysts we conducted copolymerization of ethylene and 1-hexene in the presence of three kinds of boron cocatalysts, $Ph_3C^+[B(C_6F_5)_4]^-\;(B_1),\;B(C_6F_5)_3\;(B_3)$, and $Ph_3C^+[(C_6F_5)_3B-C_6F_4-B(C_6F_5)_3]^{2-}\;(B_2)$. It turned out that all active species formed by the combination of three dinuclear CGCs with three cocatalyst were very efficient catalysts for the polymerization of olefins. The activities increase as the bridge length of the dinuclear CGCs increases. At the same time the dinuclear cocatalyst exhibited the lowest activity among three cocatalysts. The prime observation is that the dinuclear cocatalyst gave rise to the formation of the copolymers with the least branches on the polyethylene backbone.