• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.6
• /
• pp.666-673
• /
• 2014

Finite Element Method(FEM) is the essential tools for analyzing structural and vibration problem. But common commercial program is high-priced and the usage is not easy. Hereby the authors developed FEM program by using Matlab, whose usage is very simple and whose performance is very high. For the convenience of use and calculating efficiency Component Mode Synthesis Method is adopted, which divides a structure by some sub-structures for easy handling, analyzes them by parts and analyzes the structure with encompassing Degrees of Freedom(DOF). And encompassed DOF could be restored to full DOF. To confirm the accuracy the program was applied to a flat plate, and the results were compared to experiment, and good agreements were achieved. The developed program is going to be opened to public.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1158-1161
• /
• 2004

This paper describes the construction of a half sphere screen driving tilting simulator that can perform six degree-of-freedom (DOF) motions simulator to a tilting train. The mathematical equations of Tilting Train dynamics are first derived from the 6-DOF bicycle model and incorporated with the bogie, carbody, and suspension subsystems. The equations of motion are then programmed by visual C++ code. To achieve the simulator functions, a motion platform that is constructed by six electric-driven actuators is designed, and its kinetics/inverse kinetics analysis is also conducted. Driver operation signals such as carbady angle, accelerator, and tilting positions are measured to trigger the Tilting dynamics calculation and further actuate the cylinders by the motion platform control program. In addition, a digital PID controller is added to achieve the stable and accurate displacements of the motion platform. The experiments prove that the designed simulator is adequate in performing some special rail road driving situations discussed in this paper.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.833-836
• /
• 1998

The propose of this paper is to implement the master slave control with non-actuated Master Arm scheme by using spaceball. The spaceball is a device which can receive all 6-DOF at once and was selected because it isn't dependent to robot type or it's DOF but can be used to produce information about 3D coordiante system The proposed method's main benefit is that one who has no idea about robot structure can control the manipulator with easy. The simulation is supported with 3 modes of control to accomodate unexpected situation. The proposed implementation has probed that a non-trained user can manipulate the slave with intuition without much difficults.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.2
• /
• pp.108-115
• /
• 1999

This paper proposes the robot inverse calibration method using a neural networks. A highorder networks called Pi-Sigma networks has been used. The Pi-Sigma networks uses linear summing units in the hidden layer and product unit in output layer. The inverse calibration model which compensates the difference of joint variables only between measuring value and analytic value about the desired pose(position orientation) of a robot is proposed. The compensated values are determined by using the weights obtained from the learning process of the neural networks previously. To prove the reasonableness the SCARA type direct drive robot(4-DOF) and anthropomorphic robot(6-DOF) are simulated. It shows that the proposed calibration method can reduce the errors of the joint variables from $\pm$3 to $\pm$0.1.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.5
• /
• pp.138-145
• /
• 1998

Recently, TCS(Traction Control System) is attracting attention, because it maintains traction ability and steerability of vehicles on low-$\mu$ surface roads by controlling the slip rate between tire and road surface. The development of TCS control law is difficult due to the highly nonlinearity and uncertainty involved in TCS. A fuzzy logic approach is appealing for TCS. In this paper, fuzzy logic controller for TCS is introduced and evaluated by the computer simulation with 8 DOF vehicle model. The result indicate that the fuzzy logic TCS improves vehicle's stability and steerability.

• Smart Structures and Systems
• /
• v.25 no.4
• /
• pp.393-399
• /
• 2020

In this paper, the design method and experimental validation for the two-degree-of-freedom (2DOF) electromagnetic energy harvester are presented. The harvester consists of the rigid body suspended by four tension springs and electromagnetic transducers. Once the two resonant frequencies and the mass properties are specified, both the constant and the positions for the springs can be determined in the closed form. The designed harvester can locate two resonant peaks close to each other and forms the extended frequency bandwidth for power harvesting. Halbach magnet array is also introduced to enhance the output power. In the experiment, two resonant frequencies are measured at 34.9 and 37.6 Hz and the frequency bandwidth improves to 5 Hz at the voltage level of 207.9 mV. The normalized peak power of 4.587 mW/G² is obtained at the optimal load resistor of 367 Ω.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.24 no.1
• /
• pp.55-61
• /
• 2016

In this work a guidance and control system for an a powered ram air parafoil under wind disturbance is considered. After analyzing a 6 Dof and 9 Dof nonlinear dynamic models of the parafoil, wind effect is added to them. In order to actively respond to the wind acting on the transverse direction of the vehicle a new guidance algorithm is proposed. After a Hardware-In-the-Loop Simulation (HILS) study, flight tests are performed to demonstrate its potential under wind disturbances.

• Korean Journal of Computational Design and Engineering
• /
• v.9 no.3
• /
• pp.212-219
• /
• 2004

This paper presents the visualization method of the KAIST interactive bicycle simulator. The simulator consists of two bicycles of 6 DOF and 4 DOF platforms, force feedback handlebars and pedal resistance systems to generate motion feelings; a real-time visual simulator, a HMD and a beam projection system; and a 3D sound system. The system has an integrating control network with the server-client network structure for multiple simulators. The visual simulator generates dynamic images in real-time while communicating with other modules of the simulator. The operator of the simulator can have realistic visual experience of riding on a velodrome or through the KAIST campus, while being able to watch the other bicycle with an avatar.

• Journal of the Korean Society for Precision Engineering
• /
• v.6 no.3
• /
• pp.32-45
• /
• 1989

The positioning accuracy of robots depends upon a forward kinematics which relates the joint variables to the orientation and position of the robot extremity in the absolute coordinate system. The relationship between two connective joint coordi- nates of a robot, which is the basis of the kinematics, is defined by 4 Denavit-Hartenberg parameters. But manufacturing errors in machining and assembly process of robots lead to disctrepancies between the design parameters and the physical structure. Thus, improving the positioning accuracy of robots reguires the identification of the actual link parameters of each robot. In this study, the least-squares method is used to calibrate the link parameters and off-line parameter calibration software is developed. Computer simulation is done to study the dependence of the calibration performance upon the DOF of the robot and number of acquired data set used in the least-squares method. 3 DOF Robot/Controller and specially designed 3D coordinate measurer is made and experiment is carried out to verify the theoretical and computational analysis.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.131-136
• /
• 1999

This paper proposes the robot inverse calibration method using a neural networks. A highorder networks called Pi-Sigma networks has been used. The Pi-Sigma networks uses linear summing units in the hidden layer and product unit in output layer. The inverse calibration model which compensates the difference of joint variables only between measuring value and analytic value about the desired pose(position, orientation) of a robot is proposed. The compensated values are determined by using the weights obtained from the learning process of the neural networks previously. To prove the reasonableness, the SCARA type direct drive robot(4-DOF) and anthropomorphic robot(6-DOF) are simulated. It shows that the proposed calibration method can reduce the errors of the joint variables from $\pm$2$^{\circ}$to $\pm$ 0.1$^{\circ}$.