• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.12
• /
• pp.120-127
• /
• 2016

This study examined the dynamic characteristics of the gate to identify the optimal gate installation direction according to the installation direction. A 1:31 scale model was constructed for a 47.5m prototype gate using acrylic. The scaled weights were tuned by adding lead weights. The first step was to measure the natural frequencies of the model gates, and compare them with finite-element analysis of the prototypes as a calibration. The scaled model was tested in a 1.6 m wide concrete flume for two orientations to determine the effects of the gate orientation on structural vibrations. Vertical vibrations were measured under a range of operational conditions, including a range of bottom opening heights and different upstream and downstream water levels. For large bottom opening heights in the normal direction, relatively large vibrations were induced by vortices shed at the plate bottom that would strike the horizontal truss member. This phenomenon was avoided in the reverse direction. For small bottom opening heights in the normal direction, these vibrations were caused by a suction force that developed at the gate bottom. The gate model in the reverse direction was preferred because of its low overall vibrational response under general gate opening and flow level combinations.

• Journal of electromagnetic engineering and science
• /
• v.3 no.1
• /
• pp.1-6
• /
• 2003

In this paper, a sub-harmonic dual-gate FET mixer is suggested to improve the isolation characteristic between LO and RF ports of an unbalanced mixer. The mixer was designed by using single-gate FET cascode structure and driven by the second harmonic component of LO signal. A dual-gate FET mixer has good isolation characteristic since RF and LO signals are injected into gatel and gate2, respectively. In addition, the isolation characteristic of a sub-harmonic mixer is better than that of a fundamental mixer due to the large frequency separation between the LO and RF frequencies. As RF power was -30 ㏈m and LO power was 0 ㏈m, the designed mixer yielded the -47.17 ㏈m LO-to-RF leakage power level, 10 ㏈ conversion gain, -2.5 ㏈m OIP3, -12.5 ㏈m IIP3 and -1 ㏈m 1 ㏈ gain compression point. Since the LO-to-RF leakage power level of the designed mixer is as good as that of a double-balanced mixer, the sub-harmonic dual-gate FET mixer can be utilized instead.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.46 no.2
• /
• pp.41-47
• /
• 2004

A model test is carried out to investigate flow-induced vibration of a Tainter gate in estuary sulices. The gate model scaled with the ratio of 1:25 is made of acryl panel dimensioned 0.66 m in width, 0.5 m in height in the concrete test flume. Firstly, natural frequencies of the model gate are measured and the results are compared with the numerical results in order to verify the model. In the flow from the gate inside to the gate outside, the amplitudes of the vibration are measured under the different gate opening and downstream water level conditions. Also revised gate models with 20 mm bottom width are tested under the different gate openings and water levels. The results are analyzed to study the characteristics of the Tainter gate vibration in the sea ward flow. These test results are assessed in comparison with the results in the lake ward flow, as a result, presents the dynamic characteristics of the Tainter gate and a basic data for the guide manuals of gate management.

• The Journal of the Korea Contents Association
• /
• v.13 no.11
• /
• pp.768-777
• /
• 2013

The purpose of this study is to minimize radiation exposure to the workers and public members during CT examination. The objects are seven of the CT rooms in university hospitals and four of the CT rooms in clinics located in Busan and Gyung-nam area. The places of measurement for radiation leakage are 1) 3 m above the ground of shielding wall in the control room 2) particular space in the control room 3) worker's gate in the control room 4) the patient gate. Its values were calculated maximum leakage radiation per week(MLRW). As a result, the worker's gate of M clinic displayed the highest dose. When it was calculated by MLRW in classic method, it showed 1) $5.97{\pm}0.23$, 2) $0.50{\pm}0.02$, 3) $10.00{\pm}0.11$, 4) $2.37{\pm}0.47$ mR/week. All of them did not exceed limit for maximum permissible dose per week(MPDW). However, When MLRW of M clinic was calculated by empirical method, its value displayed $118.31{\pm}17.72$ mR/week.(MPDW>100 mR/week). Radiation leakage influenced in the control room(p<0.05). Therefore, The way of calculating MLRW must be developed and shielding wall in control room is designed 3 m above the ground for reducing dangerous of leakage radiation.

• Korean Journal of Ecology and Environment
• /
• v.47 no.3
• /
• pp.214-218
• /
• 2014

We introduce a technical equipment of GATe (Green (algae)-tide) water combine developed by K-water. The GATe water combine consists of five modules: main body and buoyant, transfer hopper, screen conveyer, sludge remover, and separator of algae and waste. Also a sprinkler, as the pre-treatment step if necessary, is equipped to the device to spread out environmental-friendly algaecide under the circumstance that the level of algal bloom does not reach to the scum-forming condition. The overall module system of this device is very simple. Based on the field test, the device covers surface area of ca. $500,000m^2day^{-1}$ during the period from May to July, and treats water volume as much as $500,000m^3day^{-1}$ in spite of some variation depending on the water quality condition. The removal efficiency of the device appeared to be over 90%. In addition, the operating duration of the device was able to expand to cover the period between March and November. We expect this new technology can be used to solve algal bloom problems in drinking water resource and public water area.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.1A
• /
• pp.47-53
• /
• 2003

This paper describes the design of a 155 Mb/s multiplexer-demultiplexer chip. This device for a 2.5 Gb/s SDH based transmission system is to interleave the parallel data of 51 Mb/s into 155 Mb/s serial data output, and is to deinterleave a serial input bit stream of 155 Mb/s into the parallel output of 51 Mb/s The input and output of the device are TTL compatible at the low-speed end, but 100K ECL compatible at the high-speed end The device has been fabricated with a 0.7${\mu}m$ BiCMOS gate array The fabricated chip shows the typical phase margin of 180 degrees and output data skew less than 470 ps at the high-speed end. And power dissipation is evaluated under 2.0W.

• Journal of the Semiconductor & Display Technology
• /
• v.10 no.4
• /
• pp.107-112
• /
• 2011

This paper is for improving the RF frequency performance of a fabricated 100nm ${\Gamma}$-gate MHEMT, scaling down vertically for the epitaxy-structure layers of the device. Hydrodynamic simulation parameters are calibrated for the fabricated MHEMT with the modulation-doped $In_{0.52}Al_{0.48}As/In_{0.53}Ga_{0.47}$As heterostructure grown on the GaAs substrate. With these calibrated parameters, simulations for the vertically-scaled epitaxial layers of the device are performed and analyzed for DC/RF characteristics, including the quantization effect due to the thickness reduction of InGaAs channel layer. A newly designed epitaxy-structure device shows higher extrinsic transconductance, $g_m$ of 1.556 S/mm, and higher frequency performance, $f_T$ of 222.5 GHz and $f_{max}$ of 849.6 GHz.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.47 no.4
• /
• pp.25-32
• /
• 2005

This study was performed to evaluate the strength properties of polymer concrete using recycled aggre-gate. The compressive strength, splitting tensile strength, flexural strength and pulse velocity of polymer concrete were decreased with increasing the content of recycled aggregate. At the curing age of 7days, the compressive strength was $80.5\~88.3$ MPa, the splitting tensile strength was $9.1\~10.6$ MPa, the flexural strength was $19.2\~21.5$ MPa and the pulse velocity was $3,931\~4,041$ m/s, respectively. Also, the compressive strength, splitting tensile strength, flexural strength and pulse velocity of concrete using recycled fine aggregate were higher than that of the silica sand. Therefore, these recycled aggregate polymer concretes were estimated for high strength concrete without major problem.

• Journal of Korean Society of Rural Planning
• /
• v.13 no.3
• /
• pp.83-90
• /
• 2007

The purpose of main entrance was to protect the house with the wall and working for the house-gate where people come in and go out. On the other hand, the type of main entrance is changed variously depended on the materials for house and method of construction. Eleven villages in the Chungyang-Gun where the environment of rural villages is well maintained was chosen and researched to make data. These data of visual landscape elements were analysed by using the SPSS 12.0 for Windows. Relations of the visual component elements were analysed by the analysis for frequency and analysis for crosstab. From the above research we could conclude below results. Through review of the pre-researching and researching literatures, 11 types of visual component elements were selected such as the types of the gate, the looking through degree of the gate, the material of the gate, the color of the gate, the plan of the house, the material of the roof, a material of the wall, a color of the wall, the form of the penetration, the area to put, the area of a site, the year of the constructing a building. For the types of the gate, the gate from without the roof has been the most popular since it appeared 41.5%. For the looking through degree of the gate, a complete blockade form has been the most popular since it appeared 63.2%. For the material of the gate, the iron plate has been the most popular since it appeared 32.1%. For the color of the gate, color has been the most popular since it appeared 68.4%. For the plan of the house, 'ㄷ' form has beneath most popular since it appeared 38.3%. For the material of the roof. The Zinc has been the most popular since it appeared 51.9%. For a material of the wall, A cement mortar has been the most popular since it appeared 47.7%. For a color of the wall, Without tile color has hem the most popular since it appeared 67.0%. For the form of the penetration. The plain form has been the most popular since it appeared 54.0%. For tile area of a site, $100m^2{\sim}200m^2$ has been the most popular since it appeared 39.0%. The results of this study can provide to use of indicates four rural-housing reform. From now on, the results look forward to offering the meaning directions for the improvement of rural house gates.

• Journal of the Korean Vacuum Society
• /
• v.20 no.5
• /
• pp.345-355
• /
• 2011

GaAs-based metamorphic high electron mobility transistors (MHEMTs) and InP-based high electron mobility transistors (HEMTs) have good microwave and millimeter-wave frequency performance with lower minimum noise figure. MHEMTs have some advantages, especially for cost, compared with InP-based ones. In this paper, InAlAs/InxGa1-xAs/GaAs MHEMTs are simulated for DC/RF small-signal analysis. The hydrodynamic simulation parameters are calibrated to a fabricated 0.1-${\mu}m$ ${\Gamma}$-gate MHEMT device having the modulation-doped $In_{0.52}Al_{0.48}As/In_{0.53}Ga_{0.47}As$ heterostructure on the GaAs substrate, and the simulations for RF small-signal characteristics are performed, compared with the measured data, and analyzed for the devices. In addition, the simulations for the DC/RF characteristics of the MHEMTs with different gate-recess structures are performed, compared and analyzed.