• 대한전자공학회논문지
• /
• 제18권6호
• /
• pp.23-29
• /
• 1981

마이크로스트립선로에 슬롯트선로를 결합시켜 평면형 광변역 balun을 설계, 제작하였다. 특히 C-band(4-8 GHz)에서 완전하게 동작시키기 위하여 슬롯트선로의 특성임피던스를 보상하여 주었으며, 이로써 이론치와 일치되는 결과를 얻을 수 있었다. 즉. 2 : 1의 부하저항에 대하여 Chebyshev 3-section 변환기로 정합회로를 구성한 결과. 3.5GHz∼7.0GHz의 1 -octave 대역에서 1.2 : 1 이하의 V.S.W.R.을 얻었으며 전송손실은 0.9dB까지 측정되었다. 특히 평형출력의 위상차는 180°±5°이내에서 linear 하게 변화하는 특성을 보이고 있다.

• 전기학회논문지
• /
• 제58권10호
• /
• pp.1916-1922
• /
• 2009

Introducing distributed generators(DGs) to utility distribution system can cause malfunction of relay on the grid when ground faults or severe load unbalances are occurred on the system. Because DGs interconnected to the grid can contribute fault currents and make bidirectional power flows on the system, fault currents from DGs can cause an interference of relay operation. A directional over current relay(DOCR) can determine the direction of power flow whether a fault occurs at the source side or load side through detecting the phases of voltage and current simultaneously. However, it is identified in this paper that the contributed fault current(Ifdg) from the ground source when was occurred to contribute single-line-to-ground(SLG) fault current, has various phases according to the distances from the ground source. It means that the directionality of Ifdg may not be determined by simply detecting the phases of voltage and current in some fault conditions. The magnitude of Ifdg can be estimated approximately as high as 3 times of a phase current and its maximum is up to 2,000 A depending on the capacity of generation facilities. In order to prevent malfunction of relay and damage of DG facilities from the contribution of ground fault currents, Ifdg should be limited within a proper range. Installation of neutral ground reactor (NGR) at a primary neutral of interconnection transformer was suggested in the paper. Capacity of the proposed NGR can be adjusted easily by controlling taps of the NGR. An algorithm for unidirectional relay was also proposed to prevent the malfunction of relay due to the fault current, Ifdg. By the algorithm, it is possible to determine the directionality of fault from measuring only the magnitude of fault current. It also implies that the directionality of fault can be detected by unidirectional relay without replacement of relay with the bidirectional relay.

• 전력전자학회논문지
• /
• 제16권3호
• /
• pp.242-249
• /
• 2011

제안하는 컨버터는 부스트 하프브리지-전압 더블러를 각각 병렬-직렬로 연결하여 출력전력 및 출력전압을 증대시키므로 고승압 대전력 응용에서 소자의 선정이 용이하다. 특히 고주파변압기 턴 비를 작게 할 수 있고 DC 오프셋이 제거되어 최적의 변압기 설계가 가능하며, 3개의 코아로 전력이 분배되어 Low Profile 및 열 분산에 유리하다. 제안하는 컨버터는 전 영역(0 ∼ 1)의 듀티 사용으로 스타트업 및 추가의 클램프회로가 필요 없으며 입력전압 변동이 큰 응용에 적합하다. 또한 넓은 듀티영역에서 스위치의 ZVS 턴온과 다이오드의 ZCS 턴온 턴오프가 성취되므로 고효율을 달성할 수 있다. 제안하는 컨버터를 5 kW급 시작품으로 검증하였다.

• 전기학회논문지
• /
• 제61권10호
• /
• pp.1542-1547
• /
• 2012

Asynchronous phenomenon occurs on the synchronous generators under power system when a generator's amplitude of electromagnetic force, phase angle, frequency and waveform etc become different from those of other synchronous generators which can follow instantly varying speed of turbine. Because the amplitude of electromagnetic force, phase frequency and waveform differ from those of other generators with which are to be put into parallel operation due to the change of excitation condition for load sharing and the sharing load change, if reactive current in the internal circuit circulates among generators, the efficiency varies and the stator winding of generators are overheated by resistance loss. When calculation method of protection settings and logic for protection of generator asynchronization will be recommended, a distance relay scheme is commonly used for backup protection. This scheme, called a step distance protection, is comprised of 3 steps for graded zones having different operating time. As for the conventional step distance protection scheme, zone 2 can exceed the ordinary coverage excessively in case of a transformer protection relay especially. In this case, there can be overlapped protection area from a backup protection relay and, therefore, malfunctions can occur when any fault occurs in the overlapped protection area. Distance relays and overcurrent relays are used for backup protection generally, and both relays have normally this problem, the maloperation, caused by a fault in the overlapped protection area. Corresponding to an IEEE standard, this problem can be solved with the modification of the operating time. On the other hand, in Korea, zones are modified to cope with this problem in some specific conditions. These two methods may not be obvious to handle this problem correctly because these methods, modifying the common rules, can cause another coordination problem. To overcome asynchronizing protection, this paper describes an improved backup protection coordination scheme using a new logic that will be suggested.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.2162-2163
• /
• 2011

현재 산업의 발전으로 인해 전기의 사용량이 증가하고 있는 상태이다. 이로 인하여 지락이나 단락과 같은 사고 발생 시 전류가 급격하게 증가하게 된다. 이러한 급격한 사고전류를 제한하기 위하여 본 논문에서는 재폐로 동작을 접목하여 전압 증가 시 사고유형별 3상 변압기형 초전도 한류기에 대해서 분석하였다. 재폐로 주기는 5-10-7-20주기로 설정하였고, 1선지락과 2선지락일 때 3상 변압기형 초전도 한류기의 전류제한에 대해서 분석해보면, 1선지락 일 때 2선지락 사고일 때보다 사고 제한율이 높은걸 확인 할 수 있다. 하지만 2개의 초전도 소자의 동시 ��치가 아닌 불균형 ��치가 일어나서 하나의 소자만이 전류를 제한하였다. 그리고 스위치가 open 되었을 때 초전도체의 회복특성은 전류제한과 마찬가지로 1선지락일 때 보다 빨리 회복되는 것을 확인 할 수 있다. 이처럼 사고 발생 시 사고전류를 낮게 제한하고, 재폐로 동작을 통하여 빠르게 사고 확인을 하여 사고를 차단할 수 있다고 사료된다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제2권1호
• /
• pp.49-55
• /
• 2002

This paper presents high performance MEMS passives using fully CMOS compatible, monolithically integrable 3-D RF MEMS processes for RF and microwave applications. The 3-D RF MEMS technology has been developed and investigated as a viable technological option, which can break the limit of the conventional IC technology. We have demonstrated the versatility of the technology by fabricating various 3-D thick-metal microstructures for RF and microwave applications, such as spiral/solenoid inductors, transformers, and transmission lines, with a vertical dimension of up to $100{\;}\mu\textrm{m}$. To the best of our knowledge, we report that we are the first to construct a fully integrated VCO with MEMS inductors, which has achieved a low phase noise of -124 dBc/Hz at 300 kHz offset from a center frequency of 1 GHz.

• 전기학회논문지
• /
• 제65권3호
• /
• pp.504-510
• /
• 2016

In general, a fault locator is installed in Sub-Station of AT(Auto-transformer) feeding system to estimate the fault location and to protect the Korean AT feeding system. Since the line impedance characteristic is different to normal 3-phase transmission line, we need particular modification factors, which can be calculated using fault location recording data, to estimate the accurate fault location. Up to recently, forcible ground test has been used to calculate the modification factors of the fault locator. However, large amount of current is occurred when the forcible ground test is performed, and this current affects to adjacent equipments. Therefore, we proposed a novel calculation method of modification factors, arbitrary trip test, using boosting current of the operating electric train. Through several field test, we confirmed that modification factors for fault locator can be easily calculated by using proposed method. Moreover, we verified the accuracy and stability of the proposed calculation method.

• 전력전자학회논문지
• /
• 제19권1호
• /
• pp.31-40
• /
• 2014

This paper describes an optimal configuration for multi-central inverters in a medium-voltage (MV) grid, which is suitable for large-scale photovoltaic (PV) power plants. We theoretically analyze a proposed common-mode equivalent model for problems associated with multi-central transformerless-type three-phase full bridge(3-FB) PV inverters employing two-winding MV transformers. We propose a synchronized PWM control strategy to effectively reduce the common-mode voltages that may simultaneously occur. In addition, we propose that the existing 3-FB topology may also have the configuration of a multi-central inverter with a two-winding MV transformer by making a simple circuit modification. Simulation and experimental results of three 350kW PV inverters in a multi-central configuration verify the effectiveness of the proposed synchronization control strategy. The modified transformerless-type 3-FB topology for a multi-central PV inverter configuration is verified using an experimental prototype of a 100kW PV inverter.

• 한국컴퓨터산업학회논문지
• /
• 제7권3호
• /
• pp.245-252
• /
• 2006

양극화로 인한 소외계층이 심화되고 고령화에 따른 사회복지가 대응하는 시간적 간격이 너무나 커지고 있다. 특히, 독거노인 환자의 증가로 인한 무관심이 사회문제로 비화되고 있는 실정이다. 더불어, 재택 골절환자의 비율도 급상승하고 있다. 국내적으로는 BT기술, 의료솔루션 기술은 현대기술의보조적 역할보다는 중추적인 역할을 제공하고 창조적 기술로 활용할 수가 있다. 특히, 초음파를 골절치료에 적용하면, 뼈가 잘 안 붙는 뼈의 골절치료 기간을 40% 가량 줄일 수 있다는 논문자료도 있다. 본 연구에서는 초음파 작동주파수가 1mHz, 1.3mHz, 1.5mHz의Piezo-ceramic crystal tranducer물질을 가지는 초음파 발생원 각각 4개를 한조로 하여 양단에 사용하였고, 임피이던스 및 Phase측정결과에 따라 외부직경이 각각4mm, 5.4mm, 두께0.5mm, 길이 70mm의 트랜스듀스를 사용하였다. 용량 50mW급으로 제작하였고, 초음파분포도를 조사하였다. <중략> 차후 시스템을 보완하면 골다공증 환자에도 적용이 될 것이고, 본 연구에서는 시제품을 직접 설계하고 비정형화 특성을 연구하고 기본적인 형태를 모델링 하여 접근해 보고자 노력해 보았다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제50권11호
• /
• pp.555-561
• /
• 2001

In this paper, the low power (1.5 W) solenoid-type magnetic thin-film transformers utilizing a $Ni_{81}Fe_{19)$ core material were designed and fabricated for 5 MHz-drive DC-DC converter application. The $20\mum$ thick copper films were used as the coils. The transformers fabricated in this work have the sizes of $3.08 mm\times25.5 mm\; and\; 6.15 mm\times12.75 mm.$ The optimum design of solenoid-type magnetic thin film transformers was performed utilizing the conventional equations, a Maxwell computer simulator (Ansoft HFSS V7.0 for PC), and parameters obtained from the magnetic properties of NiFe magnetic core materials. frequency characteristics of inductance, dc resistance (R), coupling factor (k) and gain of developed transformers were measured using HP4194A impedance and gain-phase analyzer. The fabricated transformers with the size of $6.15 mm\time12.75 mm$ exhibit the inductance of $0.83 \muH$, the dc resistance of $2.3\Omega$$\Omega$, the k of 0.91 and the gain of -1 dB at 5 MHz, which show the comparable results to those reported in the recent literatures. The measured high-frequency characteristics for the fabricated transformers agreed well with those obtained by theoretical calculations .