• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.3
• /
• pp.457-465
• /
• 1988

The inside contact characteristics in abrasive belt drives were investigated analytically and experimentally for (1) driver pulley contact wheel and (2) driven pulley contact wheel. The concentrated contact forces in the grinding zone divided the entire belt-pulley contact are by three distinct areas and the tangential friction forces in the active areas caused the normal forces to change, which resulted in the different belt force distribution compared with those of the ordinary flat belt drives. The experimental results for the normal pressure (belt tension) distribution were in good agreement with the theoretical results.

• The Journal of Korean Academy of Prosthodontics
• /
• v.25 no.1
• /
• pp.281-302
• /
• 1987

의치상 재료 종류에 따라 의치, 점막 및 하악골에 발생되는 변위 및 응력을 연구하기 위하여 컴퓨터를 이용한 수치적 해석인 2차원 유한 요소법을 이용하였다. 2차원 유한 요소 모형으로선 표준 크기의 하악골 및 의치를 고려하여 231개의 사변형 요소 및 268개의 절점으로 분할한 후 각 구성 성분의 물리적 성질인 탄성률 및 프와송비를 대입시켰다. 사용된 의치로서는 일반 합성수지의치, 2mm후경의 탄성재를 의치상 하부에 이장한 합성수지의치, 2mm후경의 탄성재를 치아와 의치상 중앙에 삽입한 합성수지의치 및 0.5mm후경의 금속상의치의 4종류였으며, 하중시에 하악의 고정 부위로선 생체와 동일 조건을 부여하기 위하여 교근, 내측익돌근, 측두근등의 하악 폐구근이 부착되는 하악각 부위 및 하악 근돌기 부위의 16절점을 고정점으로 하였다. 하중 조건으로선 하악 제1대구치의 일점에 10kg의 수직 집중하중, 하악 중절치의 일점에 7kg의 수직 집중하중 및 하악 제 1소구치로 부터 하악 제2대구치까지의 교합면에 10kg의 수직 분산하중을 부여하여 분석한 결과는 다음과 같다. 1. 하중이 의치 교합면위의 가해진 부위에 따라 다양한 의치 회전 및 강하 현상을 보였으며, 탄성재를 이장 및 삽입한 합성 수지 의치의 변위가 일반 합성수지의치 및 금속상 의치의 변위보다 더 컸다. 2. 주응력을 고려할때 점막 부위에는 주로 압축 응력이 작용하였으며 치조제 부위는 압축응력과 인장 응력이 함께 작용하였다. 3. 탄성재를 삽입한 합성수지의치에 최고 등가 응력이 집중되었으며 그 다음은 탄성재를 이장한 합성수지의치, 일반 합성수지의치의 순이였으며 금속상의 경우는 금속을 따라서 높은 등가 응력이 넓게 분산되었다. 4. 의치상 종류에 관계없이 동일 하중 조건하에선 점막에 나타나는 등가 응력의 크기 및 분산양태는 유사하였다. 5. 하악골에서 등가 응력은 의치지지 부위에만 국한되지 않고 넓게 분산 되었으며 의치상 종류 및 하중 조건에 관계없이 치조제 후방 및 하악연의 후방 부위에 특히 높은 등가응력이 집중되었다. 6. 하악 중절치의 일점에 수직 하중을 가한 경우가 다른 하중 조건에 비하여 지지점과의 거리차이로 인하여 하악골에 가장 높은 등가 응력을 유발하였다. 7. 의치상 재료에 따른 하악 골에 발생되는 응력의 크기 및 분산에는 큰 차이가 없으나 금속상의 경우가 교합압을 분산하는데는 효과적이었다.

• Journal of Korean Society of Steel Construction
• /
• v.13 no.2
• /
• pp.163-176
• /
• 2001

In this paper, the stress resultants and displacements of simply supported curved girder based on the flexural torsional theory considering torsional warping effects are analyzed. And elastic equations of continuous curved girder are obtained by using energy method. Also, bending moment warping torsional moment diagram, pure torsional moment diagram, shearing force diagram, and deflection diagram of continuos curved girder bridge subjecting to vertical loads and uniform loads are presented.

• Journal of the Korea Convergence Society
• /
• v.4 no.2
• /
• pp.21-27
• /
• 2013

Spot welding is automation of assembly process, without increasing the vehicle weight and economy, there is a fuel economy improvement of motor vehicles and to widely used in the automotive industry. But By irregular load from the road surface while at the vehicle is running, stress concentration occurs in the weld point, fatigue failure occurs frequently. Considering change of stiffness is the essential fatigue life of the evaluation spot weld. In this paper, by performing a linear static analysis was to understand the vulnerable part. Acquire to the fatigue properties of the spot weld, take the load history of the three levels in the time domain, was performed by setting as a condition of quasi-static fatigue analysis. and Fatigue life prediction method of the spot weld was by applying the method according to the fatigue damage accumulation and the conventional method was compared analyzed with the results shown.

• The Journal of Korean Academy of Prosthodontics
• /
• v.48 no.3
• /
• pp.181-188
• /
• 2010

Purpose: The purpose of this study was to compare the stress distribution characteristics of four different abutment connections on SS-$III^{(R)}$ fixture under occlusal loading, using 3-dimensional finite element method. Materials and methods: The fixture of SS-$III^{(R)}$ (Osstem, Korea) with 4 mm diameter and 11.5 mm length and 4 types of abutments were analyzed; Solid, Com-Octa, ComOcta Gold, and Octa abutment. The models were placed in the area of first molar in the mandible. The 4 loading conditions were; (1) the vertical loading of 100 N on the central fossa, (2) the vertical loading of 100 N on the buccal cusp, (3) the $30^{\circ}$ inclined loading of 100 N to lingual side on the central fossa, and (4) the $30^{\circ}$ inclined loading of 100 N to the lingual side on the buccal cusp. The 3G.Author program was used, the von-Mises stress was calculated and the stress contours were plotted on each part of the implant systems and the surrounding bone structures. Results: Regardless of abutment types and loading conditions, higher stress concentration was observed at the cortical bone. In cancellous bone, the highest stress was observed at apical portion and the maximum stress occurred at the implant neck. The higher internal stress was observed in the fixtures than in the bone. The lowest stress was observed at loading condition 1 and the stress concentration was also lower than any other loading conditions. Conclusion: Within the limitation of the result of this study, it seems that the abutment connection type does not affect much on the stress distribution of bone structure.

• Restorative Dentistry and Endodontics
• /
• v.33 no.6
• /
• pp.570-579
• /
• 2008

The purpose of this study was to investigate the distribution of tensile stress of canal obturated maxillary second premolar with access cavity and notch-shaped class V cavity restored with composite resin using a 3D finite element analysis. The tested groups were classified as 8 situations by only access cavity or access cavity with notch-shaped class V cavity (S or N), loading condition (L1 or L2), and with or without glass ionomer cement base (R1 or R2). A static load of 500 N was applied at buccal and palatal cusps. Notch-shaped cavity and access cavity were filled microhybrid composite resin (Z100) with or without GIC base (Fuji II LC). The tensile stresses presented in the buccal cervical area, palatal cervical area and occlusal surface were analyzed using ANSYS. Tensile stress distributions were similar regardless of base. When the load was applied on the buccal cusp, excessive high tensile stress was concentrated around the loading point and along the central groove of occlusal surface. The tensile stress values of the tooth with class Ⅴ cavity were slightly higher than that of the tooth without class V cavity. When the load was applied the palatal cusp, excessive high tensile stress was concentrated around the loading point and along the central groove of occlusal surface. The tensile stress values of the tooth without class V cavity were slightly higher than that of the tooth with class V cavity.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.4
• /
• pp.10-21
• /
• 2014

The joint of prefabricated steel grid composite deck is composed of concrete shear key and high-tension bolts. The flexural and shear strength of the joint were experimentally evaluated only by the bending and push-out test of the joint element. In this study the lateral load transfer behavior of the joint in deck structure system is experimentally evaluated. Several decks connected by the joint are prefabricated and loaded centrically and eccentrically. In the case of centrically loaded specimens, the analysis results show that for the same loading step the rotation angle of the joint with 4 high-tension bolts is larger than the case of the joint with 9 high-tension bolts. Consequently, flexural stiffness of deck and lateral load transfer decrease in the case of specimen with 4 high-tension bolts. But, in the case of eccentrically loaded specimens, it is found that there are no significant differences in the load transfer behavior. The further analysis results about the structural behavior of the joint show that lateral load transfer can be restricted by the load bearing capacity of the joint as well as punching shear strength of the slab. Furthermore, considering that high-tension bolts in the joint didn't reach to the yielding condition until the punching shear failure, increase in the number of high-tension bolts from 4 to 9 has a greater effect on the flexural stiffness of the joint and deck system than the strength of them.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.4
• /
• pp.318-326
• /
• 2013

The effect of finger joint location and distance from joint to joint one another on 3 point mid-concentration bending strength properties was investigated in this experiment. Resorcinol-phenol formaldehyde (RPF) and aqueous vinyl urethane (AVU) was used to domestic Pinus densiflora Sieb. et Zucc and imported Picea sitchensis Carr. that have been cut to different width of 0.15 mm between finger tip and root width and the distance from loading point to finger joint was 0, 30, 40, 50, 60 mm. The effect was not found on the location and distance of finger joint for bending modulus of elasticity, while the efficiency of bending strength property increased proportionally as the location of finger joint from the load point and the distance between finger joint increased. No influence was shown by finger joint location and distance beyond 3 times of specimen thickness, since similar values were shown between the solid wood and no destruction occurred materials.

• Journal of Korean Society of Steel Construction
• /
• v.12 no.6
• /
• pp.701-713
• /
• 2000

In this study, the 4-point bending test been performed in order to estimate effect of grinding on fatigue characteristics quantitatively for as-welded specimen, grinding specimen & TIG-dressing specimen for non load-carrying fillet welded joints subjected to pure bending. As a result of fatigue tests, fatigue strength at $2{\times}106$cycles of grinding specimen and TIG-dressing specimen has been increased compared with as-welded specimen and satisfied the grade of fatigue strength prescribed in specifications of domestics and AASHTO & JSSC. As a result of beachmark test, fatigue cracks on all specimens have occurred at several points where stress

• Journal of Korean Society of Steel Construction
• /
• v.12 no.5 s.48
• /
• pp.617-628
• /
• 2000

In this study, the 4-point bending test has been performed in order to estimate the effect of TIG-dressing on fatigue strength and fatigue characteristics quantitatively for non load-carrying fillet welded joints subjected to pure bending. As a result of fatigue tests, fatigue strength of as-welded specimens has been satisfied the grade of fatigue strength prescribed in specifications of domestics and AASHTO & JSSC, and fatigue strength at $2{\times}106cycles$ of TIG-dressing specimens has been increased compared with as-welded specimens. As the result of beachmark tests, fatigue cracks have been occurred at several points, where the radius of curvature and flank angle in the weld bead toes are low, and grown as semi-elliptical cracks, then approached to fracture. As a result of finite element analysis, stress concentration factor in weld bead toes has been closely related to the flank angel and radius of curvature, and between these, the radius of curvature has more largely affected in stress concentration factor than flank angle. As a result of fracture mechanics approaches, the crack correction factor of test specimens has been largely affected on stress gradient correction factor in case a/t is below 0.4. From the relations between stress intensity factor range estimated from FEM analysis and fatigue crack growth rate, fatigue life has been correctly calculated.