• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.12
• /
• pp.184-193
• /
• 2012

In this paper, a 5-bit 2-GS/s 2-way time interleaved pipeline ADC for high-speed serial link receiver is demonstrated. Implemented as a current-mode amplifier, the stage ADC simultaneously processes the tracking and residue amplification to achieve higher sampling rate. In addition, each stage incorporates a built-in 1-tap FIR equalizer, reducing inter-symbol-interference (ISI）without an extra digital post-processing. The ADC is designed in a 110nm CMOS technology. It comsumes 91mW from a 1.2-V supply. The area excluding the memory block is $0.58{\times}0.42mm^2$. Simulation results show that when equalizer is enabled, the ADC achieves SNDR of 25.2dB and ENOB of 3.9bits at 2.0GS/s sample rate for a Nyquist input signal. When the equalizer is disengaged, SNDR is 26.0dB for 20MHz-1.0GHz input signal, and the ENOB of 4.0bits.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.8
• /
• pp.52-59
• /
• 2007

In this paper, we analyzed and measured implant isolation characteristics for a 1.25 Gbps monolithic integrated hi-directional (M-BiDi) optoelectronic system-on-a-chip, which is a key component to constitute gigabit passive optical networks (PONs) for a fiber-to-the-home (FTTH). Also, we derived an equivalent circuit of the implant structure under various DC bias conditions. The 1.25 Gbps M-BiDi transmit-receive SoC consists of a laser diode with a monitor photodiode as a transmitter and a digital photodiode as a digital data receiver on the same InP wafer According to IEEE 802.3ah and ITU-T G.983.3 standards, a receiver sensitivity of the digital receiver has to satisfy under -24 dBm @ BER=10-12. Therefore, the electrical crosstalk levels have to maintain less than -86 dB from DC to 3 GHz. From analysed and measured results of the implant structure, the M-BiDi SoC with the implant area of 20 mm width and more than 200 mm distance between the laser diode and monitor photodiode, and between the monitor photodiode and digital photodiode, satisfies the electrical crosstalk level. These implant characteristics can be used for the design and fabrication of an optoelectronic SoC design, and expended to a mixed-mode SoC field.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.649-652
• /
• 1992

ECR(Electron Cyclotron Resonance) occure at ${\omega}_c$=${\omega}$, ${\omega}_c$:electron cycltron frequency, ${\omega}$:electromagnetic wave frequency. ECR system have several merit, 1) power transefer efficiency 2) low neutral gas pressure (below 1 mTorr) 3) high plasma density($10^{12}$ $cm^{-3}$). It is applicated variously in the field of semiconductor and new materials as the manufacturing equipment. Magnetic field in ECR system contruct resonance layer (${\omega}$=2.45GHz, $B_z$=875 Gauss) and control plasma. Plasma is almost generated at resonance layer. If the distance between substrate and resonance layer is short, uniformity of plasma is related with profile of resonance layer. Plasma have the property "Cold in Field", so directonality of magnetic field is one of the control factors of anisotropic etching. In this study, we calculate B field and flux line distribution, optimize geometry and submagnet current and improve of magnetic field directionality (99.9%) near substrate. For the purpose of calculation, vector potential A(r,z) and magnetic field B(r,z), green function and numerical integration is used. Object function for submagnet optimization is magnetic field directionality on the substrate and Powell method is used as optimization skim.

• Electrical & Electronic Materials
• /
• v.9 no.5
• /
• pp.439-444
• /
• 1996

0.15(B $a_{0.95}$ S $r_{0.05}$)O-0.15(S $m_{2(1-x}$/N $d_{2x}$) $O_{3}$-0.7Ti $O_{2}$(x=0-10[m/o]) ceramics were fabricated by mixed oxide method. Microwave dielectric properties were investigated with contents of N $d_{2}$ $O_{3}$. In the case of specimen with N $d_{2}$ $O_{3}$(6[m/o]), dielectric constant, quality factor and temperature coefficient of resonant frequency were 78.14, 2938(at 3[GHz]) and +14.19[ppm/.deg. C], respectively. By comparison its properties with undoped specimen, dielectric constant and quality factor were highly improved, but the temperature coefficient of resonant frequency was increased to positive value......

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.58-62
• /
• 1999

We fabricated a new hairpin type HTS 2-pole microstrip Bandpass filter to operate at 5.8GHz. The fabrication method was pulsed laser deposition and YBCO films were deposited on ${\alpha}$-A1$_2O_3$ substrates with a CeO$_2$ thin layer as a buffer layer. We developed a new style hairpin type filter by using interdigitide innerpole. Compared to the saute size regular hairpin type filters, our filter had a lower center frequency, bandwidth and loss by an amount of 14.5%, 29.6%, 0.5488dB, respectively. The size of the filters were 13.7${\times}$3.3mm. We did simulations on the several types of band pass filters by using HFSS and serenade. We measured growth rate and Tc of YBCO films grown on CeO$_2$/ ${\alpha}$-A1$_2O_3$ substrates which were rotated while growing films.

• Journal of the Korean Ceramic Society
• /
• v.36 no.9
• /
• pp.915-922
• /
• 1999

Microwave dielectric properties and far infrared reflectivity spectra of the (Zr0.8Sn0.2)TiO4 ceramics were inves-tigated with the various cooling rate. Dielectric constant was nearly same value while the unloaded Q value was largely affected by cooling rate. The Q.f of 42,140 at 7 GHz was obtained for the specimens with cooling rate of 1$^{\circ}C$/min. The effect of the cooling rate on the change of the ionic the electronic polarization and the intrinsic microwave loss of the specimens were investigated by the infrared reflectivity spectra from 50 to 4000cm-1 which were calculated by Kramers-Kroning analysis and the classical oscillator model. The relative tendency of microwave dielectric properties of the specimens calculated from the relfectivity data were in good agreement with the results by the post resonant method.

• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.8
• /
• pp.901-906
• /
• 2006

In this paper, the power amplifier using active bias circuits for LDMOS(Lateral Diffused Metal Oxide Semiconductor) MRF-21180 is designed and fabricated. According to change the temperature, the gate voltage of LDMOS is controlled by the fabricated active bias circuits which is made of PNP transistor to suppress drain current. The driving amplifier using MRF-21125 and MRF-21060 is made to drive the LDMOS MRF-21180 power amplifier. The variation of current consumption in the fabricated 60 watt power amplifier has an excellent characteristics of less than 0.1 A, whereas a passive biasing circuit dissipates more than 0.5 A. The implemented power amplifier has the gain over 9 dB, the gain flatness of less than $\pm$0.1 dB and input and output return loss of less than -6 dB over the frequency range 2.11 $\sim$ 2.17 GHz. The DC operation point of this power amplifier at temperature variation 0 $^{\circ}C$ to 60 $^{\circ}C$ is fixed by active bias circuit.

• Journal of Magnetics
• /
• v.16 no.2
• /
• pp.108-113
• /
• 2011

The electron spin resonance lineshape (ESRLS) function for the electron spin resonance linewidth (ESRLW) of $Cr^{3+}$ (S = 3/2) in ferroelectric lithium niobate single crystals doped with 0.05 wt% of Cr, is obtained by using the projection operator technique (POT), developed by Argyres and Sigel. The ESRLS function is calculated to be axially symmetric about the c - axis and analyzed by using the spin Hamiltonian $H_{SP}={\mu}_B(B{\cdot}{^\leftrightarrow_{g}}{\cdot}S)+S{\cdot}{^\leftrightarrow_{D}}{\cdot}S$ with the parameters g = 1.972 and D = $0.395\;cm^{-1}$. In the ca plane, the linewidths show a strong angular dependence, whereas in the ab plane, they are independent of the angle. This result implies that the resonance center has an axial symmetry along the c - axis. Further, from the temperature dependence of the linewidths that is shown, it can be seen that the linewidths increase as the temperature increases, at a frequency of v = 9.27GHz. This result implies that the scattering effect increases with increasing temperature. Thus, the POT is considered to be more convenient to explain the scattering mechanism as in the case of other optical resonant systems.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.1
• /
• pp.757-759
• /
• 2005

최근에 낮은 가격과 전력을 내세워 응용서비스를 제공할 수 있는 Bluetooth를 탑재한 많은 무선 제품들이 출시되고 있다. 그러나 1Mbps의 저속, 다른 무선 기기들과의 상호 간섭과 호환성 문제 그리고 보안 문제 등 많은 제약 조건이 따름에도 불구하고 이동전화, 컴퓨터, PDA 등 근거리 무선접속을 사용하고 있는 가정이나 회사의 전화나 컴퓨터들과 어떻게 서로 쉽게 연결될 수 있을까에 대한 꾸준한 연구가 활발히 진행되고 있다. Bluetooth 무선 기술은 음성 및 데이터 전송을 위한 단거리 일대다중 무선 주파수 통신을 위해 제안된 무선통신 기술이다. Bluetooth는 2.4GHz ISM Band에서 동작하며 약 10m 범위의 다양한 이동 장치와 휴대용 장치를 위한 저가격의 기저대역 무선 접속을 제공한다. 본 논문에서 Bluetooth의 기술적 측면을 알아보고 이를 이용해 현재 시장에 출시된 Bluetooth 기기중 하나인 One Phone을 소개하려 한다. 또한 Bluetooth의 발전 가능성에 대하여 알아본다.

• Journal of information and communication convergence engineering
• /
• v.11 no.3
• /
• pp.147-152
• /
• 2013

A novel balun being the structure of a Wilkinson power divider is suggested and fabricated. One of the power dividing paths in the suggested balun uses a conventional ${\lambda}/4$ transmission line for $-90^{\circ}$ phase shifting, and the other path uses a composite right/left-handed -${\lambda}/4$ transmission line for $+90^{\circ}$ phase shifting with four series capacitors and three parallel inductors. In addition, the suggested balun uses two $50-{\Omega}$ resistors and a conventional $50-{\Omega}$ transmission line of ${\lambda}/2$ electrical length between the two output ports, achieving good isolation and reflection values of two balanced ports. The suggested balun is simulated by the advanced design system simulation program and fabricated on TLX-9 20-mil substrate. The fabricated balun has a very good values of $S_{11}$ = -27.46 dB, $S_{21}$ = -3.40 dB, and $S_{31}$ = -3.28 dB, a phase difference of $-179.5^{\circ}$, a magnitude difference of 0.12 dB, and a delay difference of 0.1 ns, with $S_{22}$ = -36.28 dB, $S_{33}$ = -27.19 dB, and $S_{32}$ = -25.2 dB at 1 GHz, respectively.