• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.881-884
• /
• 2000

Recently mobile communication fields need piezoelectric ceramic resonators and filters as possible as small. The length-extensional vibration mode of a rectangular piezoelectric cesamic plate has the advantage of the small size, but the mode has not been studied sufficiently because it was not used extensively until now. In this paper, PZT + x[wt%l $Cr_20_3$ ceramics with rhombohedra1 phase were fabricated. And temperature stability for the mode of the ceramic specimen was investigated. Contrary to our expectations, addition of the stabilizer, $Cr_20_3$ did not promote the temperature stability for the mode in the PZT ceramic specimen with rhombohedra1 phase.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.5
• /
• pp.911-920
• /
• 1989

It this study, beam-type bend specimen is used to evaluate the interlaminar fracture toughness of laminated composite under mixed-mode deformations. The specimen is loaded under three-point bending and hence produced mixed-mode deformations in the vicinity of the crack tip according to the variation of the thickness ratio on delamination plane. Total energy release rate is obtained by elementary beam theory considering the effect of shear deformation. The partitioning of total value into mode-I and mode-II components is also performed. The mixed-mode interlaminar fracture toughness is evaluated by experiments on specimens with several thickness ratios of delamination plane. As the part of delamination plane is thicker, the effect of shear deformation on total energy release rate is increased. Beam-type bend specimen men may be applied to obtain informations on the mixed-mode interlaminar fracture behavior of laminated composites.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.46 no.1
• /
• pp.57-63
• /
• 2019

This study aimed to determine whether the curing times of Xtra Power and High Power modes of high-power light emitting diode (LED) curing light are sufficient for polymerization of resin sealants. The specimens were prepared and their microhardness values were measured and compared with those of specimens polymerized under conventional LED curing light. The filled sealant polymerized for 8 seconds in the High Power mode and for 3 seconds in the Xtra Power mode showed significantly lower microhardness than the control specimen (p = 0.000). The unfilled sealant polymerized for 8, 12 seconds in the High Power mode and for 6 seconds in the Xtra Power mode showed significantly lower microhardness than the control specimen (p = 0.000). The results of this study suggest that the short curing time with the Xtra Power and High Power modes of highpower LED curing light are not sufficient for adequate polymerization of sealants under specific conditions, taking into account the curing times and the type of sealant.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.12
• /
• pp.3638-3644
• /
• 2009

A CMOS multi-channel low-voltage current mode filter circuit is designed. The designed current-mode filter is based on linear cascode current-mode integrator that is newly proposed in this paper. When it is compared with that of the typical current-mirror type current-mode integrator, the proposed linear cascode current-mode integrator achieves high current gain and unity gain frequency. The designed filter is composed with 5th Chebyshev function and converted to active version by signal flow graph method. We verified that the designed filter can be applied to three-channel basedband, bluetooth, DECT and WCDMA with 0.51MHz~7.03MHz frequency tuning range by Hspice simulation using 1.8V-$0.18{\mu}m$ CMOS technology.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.2
• /
• pp.93-97
• /
• 2009

An advantage of a magnetostrictive strip transducer for a long-range guided wave inspection is that the wave patterns are relatively clear and simple when compared to a conventional piezoelectric ultrasonic transducer. Therefore, if we can characterize the evolution of defect signals, it could be a promising tool for a structural health monitoring of pipes for a long period of time as well as an identification of flaws. However, when evaluating a signal during a realistic field examination, it should be careful because of some spurious signals or false indications, such as signals due to a directionality, multiple reflections, mode conversion, geometrical reflections etc. Mode converted signals from a realistic piping mockup were acquired and analysed. We found mode conversions between a torsional guided wave T(0,1) mode and a flexural F(1,3) or longitudinal L(0,2) mode generated by a magnetostrictive strip transducer. Based on the experimental observations, an interpretation of the source of the mode conversion is discussed in a viewpoint of electromagnetic properties and structure of the strip transducer.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.2
• /
• pp.115-124
• /
• 2004

This paper suggested the vibration characteristic improvement by variation mode of ring type ultrasonic motor. Design for the piezoelectric ceramic and elastic body of stator were calculated by the finite element method(FEM) that consider the resonance frequency, vibration mode and coupling efficiency etc. Through the result of vibration analysis from 6 order mode to 8 mode, the 7 order mode was gained very an excellent results that it was the coupling efficient, minimum power loss and bending vibration value. Here over 7 order mode, was acquired that an output current for input voltage was very a large increased results. The result of vibration calculation, from thickness 0.5[mm] to 2[mm], know the fact that the vibration displacement at 0.5[mm] is an high value too. From such analysis result, this paper was manufactured the ultrasonic motor of outer diameter 50[mm], inter 22[mm] having the about 43.86[KHz] resonance frequency. We have gated that a simulation result is 42.2[KHz] and an experiment result is 43.86[KHz]. Then, a propriety of this paper was established the result almost similar to though comparison, investigation of simulation and experiment result.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.4
• /
• pp.793-798
• /
• 2016

In this work, the memory window characteristics of vertical nanowire device with asymmetric source and drain was analyzed using bipolar junction transistor mode for 1T-DRAM application. A gate-all-around (GAA) MOSFET with higher doping concentration in the drain region than in the source region was used. The shape of GAA MOSFET was a tapered vertical structure that the source area is larger than the drain area. From hysteresis curves using bipolar junction mode, the memory windows were 1.08V in the forward mode and 0.16V in the reverse mode, respectively. We observed that the latch-up point was larger in the forward mode than in the reverse mode by 0.34V. To confirm the measurement results, the device simulation has been performed and the simulation results were consistent in the measurement ones. We knew that the device structure with higher doping concentration in the drain region was desirable for the 1T-DRAM using bipolar junction mode.

• ETRI Journal
• /
• v.30 no.2
• /
• pp.290-300
• /
• 2008

We apply IEEE 802.3 frame burst mode (FBM) to the Ethernet passive optical network (EPON) downstream link and compare its performance with non-frame burst mode for various traffic patterns. Although in light traffic loads (p<0.5) the efficiency of the FBM mechanism is not significant, it does feature high throughput, small jitter, low queue occupancy, and short queuing delay in optical line terminals under various traffic loads with various numbers of optical network units (ONUs). The FBM performance always approaches that of full-duplex mode, especially under heavy traffic loads (p>0.5). Moreover, an increase in number of ONUs will decrease the burst performance. Our work shows that FBM scheme is very useful for EPON transmission and has low design complexity.

• Journal of KSNVE
• /
• v.6 no.4
• /
• pp.447-456
• /
• 1996

Dynamic characteristics of the bell-type structure including acoustic effects and transient dynamic problems were analyzed numerically. Natural frequencies, mode shapes and transient dynamic analysis used the finite element method with 3-D general shell element. Mode shapes and stress distributions of transient dynamic analysis were expressed by computer graphics. The method using this study was evaluated by comparision of theoretical results at reference papers(14), (15) and the experimental test using Fast Fourier Transform analyzer. Vibrational modes governing acoustic characteristics of the typical bell-type structure depended on the first flexural mode(4-0 mode) and the second flexural mode(6-0 mode). Asymmetric effects by Dangiwas, acoustic holes gave rise to beat frequencies, and the Dangjwa was found to be most effective. When impact load acted on the bell, stress concentration occured at the rim part of bell. It was found that the bell type structure should be designed thickly at the rim part in order to prevent impact load from stress concentration.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.9 no.2
• /
• pp.104-109
• /
• 2009

At a lower supply voltage, voltage-mode drivers draw less current than current-mode drivers. In this paper, we newly propose a voltage-mode driver with an additional current path that reduces the output voltage swing without the need for complicated additional circuitry, compared to conventional voltage-mode drivers. The prototype driver is fabriccated in a 0.13-$^{\mu}m$ CMOS technology and used to transmit data streams at the rate of 2.5 Gb/s. Deemphasis is also implemented for the compensation of channel attenuation. With a 1.2-V supply, it dissipates 8.0 mA for a 400-mV output voltage swing.