• Journal of Korea Water Resources Association
• /
• v.37 no.12
• /
• pp.1009-1018
• /
• 2004

A systematic method using an optimal estimation algorithm is presented for simultaneous estimation of diffuse pollution distributed along a stream reach and model parameters for a stream water quality model. It was applied with the QVAL2E model to the South Han River for optimal estimation of kinetic constants and diffuse loads along the river. Initial calibration results for kinetic constants selected from a sensitivity analysis reveal that diffuse source inputs for nitrogen and phosphorus are essential to satisfy the system mass balance. Diffuse loads for total nitrogen and total phosphorus were estimated solving the expanded inverse problem. Comparison of kinetic constants estimated simultaneously with diffuse sources to those estimated without diffuse loads, suggests that diffuse sources must be included in the optimization not only for its own estimation but also for adequate estimation of the model parameters. Application of optimization method to river water quality modeling is discussed in terms of the sensitivity coefficient matrix structure.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.5
• /
• pp.145-154
• /
• 2003

In this study, the variation in excess pore pressure during dissipation is estimated by using successive cavity expansion theory and finite difference technique based on axisymmetric uncoupled linear consolidation theory with separate consideration of magnitude and initial distribution $\Delta{u}_{oct}$induced by changes of octahedral normal stress, and $\Delta{u}_{shear}$ induced by changes of octahedral shear stress. The coefficient of consolidation is also estimated by trial and error procedure until the predicted dissipation curve matches the measured curve at a typical degree of dissipation. The proposed method is applied to the results of miniature piezocone tests at Louisiana State University calibration chamber system. Based on the results of interpretation and the comparison with experimental measurements and those from other solutions, the prediction dissipation curves show a good match with those measured during dissipation tests and the values of coefficient of consolidation estimated by proposed method are more close to the range of laboratory measurements than those of other theories.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.36S no.8
• /
• pp.48-54
• /
• 1999

A new method for wavelet embedded image coding is presented extending the bases of the Shapiro's algorithm by incorporating edge detection, zerotree scheme, and classified VQ(CVQ). Generally edges in the image are regarded an visually important components and the previous literatures have proved that significant coefficients in wavelet transform domain correspond to the edges in spatial domain. Hence, by identifying the edge elements, the significant coefficient can be easily detected in wavelet domain without investigating descendant coefficients across layer. Hierarchical trees for the significant components are organized, and then CVQ method is applied to these trees. Since the significant information has higher priority in transmission, the simulation shows that our coder provides a superior performance over the conventional method and can be successfully applied to the application areas that require of progressive transmission.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.12
• /
• pp.87-94
• /
• 2003

In this paper, we propose an IFFT/FFT design method to minimize quantization error in IEEE 802.11a WLAN. In the proposed algorithm, the twiddle coefficient of IFFT/FFT processor is manipulated by the statistics distribution of the input data at each stage. We applies this algorithm to radix-2/$^2$ SDF architecture. Both IFFT and FFT processor shares the circuit blocks cause to the symmetric architecture. The maximum quantization error with the 10 bits length of the input and output data is 0.0021 in IFFT and FFT that has a self-loop structure with the proposed method. As a result, the proposed architecture saves 3bits for the data to keep the same resolution compared with the conventional method.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.25 no.4
• /
• pp.244-254
• /
• 2013

In this study, a method has been developed for estimating the change of nearshore random waves in response to sea-level rise, by extending the method proposed for regular waves by Townend in 1994. The relative changes in wavelength, refraction coefficient, shoaling coefficient, and wave height for random waves are presented as functions of relative change in water depth. The changes in wavelength and refraction coefficient are calculated by using the significant wave period and principal wave direction in the regular-wave formulas. On the other hand, the changes in shoaling coefficient and wave height are calculated by using the formulas proposed for shoaling and transformation of random waves in the nearshore area including surf zone. The results are proposed in the form of both formulas and graphs. In particular, the relative change in wave height is compared with the result for regular waves.

• Geotechnical Engineering
• /
• v.13 no.4
• /
• pp.85-94
• /
• 1997

The design and construction of underground structures contain many substantial mincer dainties. A reasonable estimation of geotechnical parameters is of paramount importance and must be one of the most difficult tasks in designing and constructing underground structures. If the plastic zone exists by tunnel excavation, the ground response may also be dependent on the yield criterion mainly composed of strength parameters. In order to estimate unknown model parameters from the in-situ measurements as well as prior estimates for designing tunnels which have plastic zones, the Extended Bayesian Method(EBM) is adopted : an elasto-plastic finite element program is linked to the EBM as a mathematical model to predict the ground response. Mohr-Coulomb failure criterion is used to represent the plastic behavior. A hypothetical underground site, where the ground behaves elasto-plastically, is adopted to demonstrate the validity of the proposed feedback system.

• Geotechnical Engineering
• /
• v.13 no.4
• /
• pp.95-108
• /
• 1997

For normally consolidated clay, several researchers have developed a number of theoretical time factors to determine the coefficient of consolidation However, depending on the assumptions and analytical techniques, it could considerably vary even for a specific degree of consolidation. In this paper, a method is proposed to determine a consistent coefficient of consolidation over all ranges of degree of consolidation by applying the concept of the Optimum Design Technique. The initial excess pore pressure distribution is assumed to be obtainable by the successive spherical cavity expansion theory. The dissipation of pore pressure is simulated by means of two dimensional linear-uncoupled axisymmetric consolidation analysis. The minimization of the differences between the measured and the predicted excess pore pressures was carried by BFGS unconstrained optimum design algorithm with one dimensional golden section search technique. By analyzing numerical and real field examples, it can be found that the adopted optimum technique gives a consistent and convergent results.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.5
• /
• pp.109-122
• /
• 2002

The water content of soil near the ground subgrade varies seasonally, and dynamic deformational characteristics of soil are affected by the variation of water content. Contrary to previous studies which used various specimens of different compaction moisture contents, the influences of water content and capillary Pressure on dynamic deformational characteristics of soil were investigated using the given specimen controlling the matric suction. RC/TS(resonant column and torsional shear) testing equipment was modified so that it can control water content with changing capillary pressure(matric suction). RC/TS tests were performed on subgrade soil collected in the KHC(Korea Highway Corporation) test road. In the field, the cross-hole tests were performed and the water contents were measured at the same site to verify the feasibility and applicability of RC/TS test results. As water content decreased, the tendency of increasing shear moduli in field was well matched with laboratory test results.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.12
• /
• pp.65-76
• /
• 2012

In this study, probabilistic analysis of seepage through a two-layered soil foundation was performed. The hydraulic conductivity of soil shows significant spatial variations in different layers because of stratification; further, it varies on a smaller scale within each individual layer. Therefore, the deterministic seepage analysis method was extended to develop a probabilistic approach that accounts for the uncertainties and spatial variation of the hydraulic conductivity in a layered soil profile. Two-dimensional random fields were generated on the basis of the Karhunen-Lo$\grave{e}$ve expansion in a manner consistent with a specified marginal distribution function and an autocorrelation function for each layer. A Monte Carlo simulation was then used to determine the statistical response based on the random fields. A series of analyses were performed to verify the application potential of the proposed method and to study the effects of uncertainty due to the spatial heterogeneity on the seepage behavior of two-layered soil foundation beneath water retaining structure. The results showed that the probabilistic framework can be used to efficiently consider the various flow patterns caused by the spatial variability of the hydraulic conductivity in seepage assessment for a layered soil foundation.

• Journal of Energy Engineering
• /
• v.16 no.4
• /
• pp.181-186
• /
• 2007

In order to investigate the heat transfer coefficient and pressure drop during evaporation of $CO_2$, basic experiment on the evaporation heat transfer characteristics in a horizontal smooth tube was performed. The experimental apparatus consisted of a test section, a DC power supply, a heater, a chiller, a mass flow meter, a pump and a measurement system. Experiment was conducted for various mass fluxes ($200{\sim}1200\;kg/m^2s$), heat fluxes ($10{\sim}80\;kW/m^2$) and saturation temperatures ($-5{\sim}5^{\circ}C$). With the increase of quality, the evaporation heat transfer coefficient decreased. With the increase of heat flux, the evaporation heat transfer coefficient increased. Significantly change of the heat transfer coefficient was observed at any heat flux and mass flux. With the increase of saturation temperature, the heat transfer coefficient increased. Pressure drop increased with the increase of mass flux and the decrease of saturation temperature.