• Journal of Cadastre & Land InformatiX
• /
• v.52 no.1
• /
• pp.5-16
• /
• 2022

Based on the general formula for the area error of a polygon and rectangular parcel, the constant term 0.026² × M (scale denominator) of the area error calculation formula prescribed by the Enforcement Decree was analyzed. As a result, it is found that the formula appropriately reflects the characteristics of the graphical surveying as a typical rectangular parcel model, but quantitatively allows a relatively large area error. In addition, it is found that, even if the area is the same, 50% more area error than a square parcel could be calculated depending on the shape of the parcel, and that the allowable area error should be different when dividing a parcel. Based on the analysis, furthermore, this study shows a solution that can solve the problems at once from the point of cadastral surveying. These are, the problem of reflecting the accuracy of the surveying, the problem of reflecting the size and shape of the parcel, and the problem whether a single area error formula can be used without having to distinguish between graphical and numerical surveyings. The new formula that solves these problems will bring about improvements in many related factors and promote the development of digital cadastral system.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.35 no.6
• /
• pp.509-516
• /
• 2017

In cadastral surveying, there are problems that no area error is allowed where numerical surveying is carried out, and allowable area error is specified irrespective of parcel shape where graphic surveying is carried out. In this research, we derived a general formula of parcel area error necessary for grasping these two problems. The calculations using the derived formula showed that where the coordinate error of the boundary point is set to 5cm+10ppm practically, then even a small parcel of $100 m^2$ includes non-negligible area error of $0.71m^2$. And, it is found that the area error specified by the current egulation is based on a rectangular parcel of 1:5 aspect ratio. These results show that the area error of polygon parcel can be determined by a single formula by specifying the coordinate error of the boundary points, and can be used to revise the current regulations that can be applied uniformly regardless of surveying methods.

• Journal of Korean Society for Geospatial Information Science
• /
• v.8 no.1 s.15
• /
• pp.111-120
• /
• 2000

A cadastral map that is base map on Land Information System is divided by two categories, graphical and digital cadastre. And digital cadastre can be displayed with location coordinates of nodes that depict parcel boundary on digital cadastral records. The transformation of digital cadastral records means that imported text data of node coordinate would be transformed into system data. This study was implemented to search reasons of errors resulted from transformation of graphic data and then to analyze the accuracy in terms of Position and area. For this, checking of software used in Geo-Spatial Information System was implemented at first and it was found that the accuracy is up by using double precision in coordinate transformation. On the position accuracy the errors at nodes was erased during making topology and the errors did not effect other nodes. On the area may the area errors because of being in error limit of allowable area had no problems in using of system.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 2008.10a
• /
• pp.350-351
• /
• 2008

현재 우리나라의 측량체계는 크게 측지분야와 지적분야로 이원화되어 있으며 측지분야에서는 2001년도에 측량법을 개정하여 ITRF2000좌표계와 GRS80 타원체를 측량기준으로 사용하는 세계측지계를 도입하였다. 하지만 지적 분야에서는 국민의 재산권과 직접적으로 관련이 있는 필지의 경계와 면적의 변화 연구는 미미한 상태이다. 따라서 본 연구는 2010년 세계측지계 도입 후 지적분야에서 발생할 수 있는 필지별 면적 변동에 따른 사회적 혼란 여부를 판단하기 위하여 서울특별시 종로구 숭인등 숭인4구역주택재개발지구를 연구 대상지로 선정하여 세계측지계 전환에 지적 필지별 면적 변화를 분석하였다. 분석결과 연구대상지는 세계측지계와 지역측지계가 종선(X)축으로 305.87m. 종선(Y)축으로 70.87m 편차로 두 좌표계 간 북동방향으로 313.97m의 차이가 있고, 현행성과와 비교한 결과 종선(X) 방향으로는 평균 +4.0cm, 횡선(Y) 방향으로는 평균 -3.0cm의 차이가 나타났으며, 필지별 면적의 변동량은 $1.0m^2{\sim}3.0m^2$ 차이가 있지만 허용오차 범위 내에 있으므로 세계측지계 전환에는 문제점이 없는 것으로 판단된다. 하지만 본 연구의 결과는 그 대상범위가 한정되어 있고 기 검증된 지적기준점 성과를 사용한 결과이므로, 향후 보다 효율적인 세계측지계 전환과 도입을 위해서는 현 지적기준점체계의 정확한 세계좌표계 변환 성과를 기준으로 한 대단위의 필지별 면적 변동량 및 허용범위 분석과 같은 추가적인 연구가 조속히 이루어져야 할 것으로 판단된다.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.24 no.1
• /
• pp.80-91
• /
• 2021

The purpose of this study is to present the applicability to the effective survey into the actual condition of lands such as analysis of occupied location of government owned lands based on orthoimages created from aerial photographs taken by UAV. The boundary point coordinates and areas of the parcels were observed respectively by VRS-GNSS surveying and orthoimages for each land use of two categories of land, i.e. building site and farmland. As a result of comparing boundary point coordinates and areas extracted from UAV orthoimages with VRS-GNSS surveying data which were used as reference data, the RMS error of the coordinates for the boundary points was ±0.074m for both X and Y in the building site, and ±0.150m and ±0.127m for the X and Y respectively in the farmland. The positional error of the boundary point was 1.7~ 2 times higher in the farmland than in the building site where the boundary points were relatively clear. The RMS error of ±8.964㎡ of areas in the farmland was 4.7 times higher than that of ±1.898㎡ of areas in the building site. The area errors of all 22 parcels measured from the orthoimage were found to be within the allowed error range, indicating that it is feasible to apply the orthoimage generated by UAV to survey of government owned lands in terms of accuracy.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.5
• /
• pp.61-70
• /
• 2017

Robust thrust distribution method of solid DACS is researched. For the case of the system which has higher number of actuation nozzles than the degree of freedom of thrust to be controlled, the robust thrust allocation law which accommodate the abnormal operation is suggested. Assuming the situation that some nozzles are uncontrollable, the error between nozzle throat area command and response can be calculated. The error is used for realtime reshaping of weighting matrix. From the weighting effect, the nozzle which operated abnormally has low responsibility for the command then, the thrust error is reduced. The suggested algorithm is verified by the simulation of abnormal operation condition of DCS and ACS nozzle respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.16 no.11
• /
• pp.1132-1142
• /
• 1991

This paper proposed a method of feature parameter extraction for shape information analysis of moving object. In the 2-D plane, moving object are extracted by the difference method. Feature parameters of moving object are chosen area, perimeter, a/p ratio, vertex, x/y ratio. We changed brightness variation from the range of 600Lux to the 1400Lux and then determined Permissible Error range of feature parameter due to the brightness variation. So as to verify the validity of proposed method, experiment are performed with a toy car and it's results showed that decision error was less than 6%.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 2008.06a
• /
• pp.419-426
• /
• 2008

본 논문에서는, 건설도면의 건물 경계선을 이용하여 기존 지형도의 건물 레이어를 자동 갱신하는 과정에서 건물 객체간 유사를 측정하는 과정에서 Hausdorff 거리 측정 방법을 적용해 보았다. 서로 다른 축척에 의하여 발생하는 형상의 세일도 차이에서 발생하는 오차를 최소화하기 위하여 partial Hausdorff 거리를 적용하였다. 이 때 partial fraction을 정의하기 위한 기준으로 폴리곤 절점, 경계선 길이, 폴리곤 면적을 이용한 세 가지 방법을 적용하였다. 이 기준을 실제 데이터에 적용한 결과, 경계선 기준과 폴리곤 면적 기준 방법이 절점 기준에 비하여 안정적이라는 것과, 적용 기준에 따라 적절한 partial fraction 값을 사용하면 잡음에 의한 영향을 최소화할 수 있다는 것을 확인할 수 있었다.

• Journal of KIISE
• /
• v.42 no.6
• /
• pp.769-780
• /
• 2015

Smoothing a digital curve by averaging its connected points is widely employed to minimize sharp changes of the curve that are generally introduced by noise. An appropriate degree of smoothing is critical since the area or features of the original shape can be distorted at a higher degree while the noise is insufficiently removed at a lower degree. In this paper, we provide a mathematical relationship between the parameters, such as the number of iterations, average distance between neighboring points, weighting factors for averaging and the moving distance of the point on the curve after smoothing. Based on these findings, we propose to control the smoothed curve such that its deviation is bounded particular error level as well as to significantly expedite smoothing for a pixel-based digital curve.

• Journal of Korean Society for Geospatial Information Science
• /
• v.6 no.2 s.12
• /
• pp.119-132
• /
• 1998

Much information on the terrain and the space has been depicted to maps of various form according to the map scale and the application. In Korea the base map system was made by only one projection method(Transvers Mercator projection). This is the reason to study this paper, because I think singular map projection method can't satisfy the various map scales and application. In this paper Meridian Are Length, Parallel Are Length of ellipsoid and the area of ellipsoidal surface-the length, the width and area of the map scale 1/5,000, 1/25,000, 1/5,000, 1/1,000, will be calculated and transformed to the plane length and area by Transvers Mercartor projection and Polyhedrical projection. The projection distortion which came into existence on this occasion was compared and analyzed by this Paper. And Properties on TM and Polyhedrical projection were understood. Lastly this paper intended to present suitable map projections according to the map scales and the purpose of use.