• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.255-258
• /
• 1999

This paper describes a 40-Msample/s 10-bit CMOS folding and interpolating analog-to-digital converter (ADC). A new 2-step architecture is proposed. The proposed architecture is composed of a coarse ADC bloch for the 6bits of MSBs and a fine ADC block for the remaining 4bits. The amplified folding analog signals in the coarse ADC are selectively chosen for the fine ADC. In the fine ADC, the bubble errors of the comparators are corrected by using the BGM(binary-gray-mixed) code[1] and extra two comparators are used to correct underflow and overflow errors. The proposed ADC was simulated using CMOS 0.25${\mu}{\textrm}{m}$ parameters and occupies 1.0mm$\times$1.0mm. The power consumption is 48㎽ at 40MS/s with 2.5-V power supply. The INL is under $\pm$2.0LSB and the DNL. is under $\pm$1.0LSB by Matlab simulations.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.8 s.350
• /
• pp.19-26
• /
• 2006

In this paper, CMOS analog-to-digital converter (ADC) with a 6-bit 100MSPS at 1.8V is described. The architecture of the proposed ADC is based on a folding type ADC using resistive interpolation technique for low power consumption. Further, the number of folding blocks (NFB) is decreased by half of them compared to the conventional ones. A moebius-band averaging technique is adopted at the proposed ADC to improve performance. With the clock speed of 100MSPS, the ADC achieves an effective resolution bandwidth (ERBW) of 50MHz, while consuming only 4.5mW of power. The measured result of figure-of-merit (FoM) is 0.93pJ/convstep. The INL and DNL are within ${\pm}0.5 LSB$, respectively. The active chip occupies an area of $0.28mm^2$ in 0.18um CMOS technology.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.11
• /
• pp.74-81
• /
• 2007

In this paper, CMOS analog-to-digital converter (ADC) with a 6-bit 1GSPS at 1.8V is described. The architecture of the proposed ADC is based on a folding type ADC using resistive interpolation technique for low power consumption. To reduce the power consumption, a folder reduction technique to decrease the number of folding blocks (NFB) by half of the conventional ones is proposed. further, a novel layout technique is introduced for compact area. With the clock speed of 1GSPS, the ADC achieves an effective resolution bandwidth (ERBW) of 500MHz, while consuming only 60mW of power. The measured INL and DNL were within $\pm$0.5 LSB, $\pm$0.7 LSB, respectively. The measured SNR was 34.1dB, when the Fin=100MHz at Fs=300MHz. The active chip occupies an area of 0.27$mm^2$ in 0.18um CMOS technology.

• Journal of Sensor Science and Technology
• /
• v.30 no.2
• /
• pp.88-93
• /
• 2021

In this paper, a folding sensor based on capacitance is proposed. The sensor was developed to sense the length and angle data for the milli-scale actuators without causing any interference to the actuating joints. For the sensing and testing the robotic joint with reducing the cost and complexity aspects of manufacturing, a simple composition was adopted. The sensor comprises a pair of copper tapes, papers, and wires. The complete sensing unit is constructed by bonding the tapes with the papers and soldering the wire to the copper parts. For accuracy, a teensy 4.0 board, which has a 12-bit ADC resolution, is employed. Furthermore, the sensed analog data is not translated into the unit of capacitance for accuracy; however, it is filtered using a low-pass filter and subsequently, a Butter-worth filter. The data obtained demonstrate a periodic waveform, which implies that the data are in good agreement with the hypothesis set prior to the experiments. Compared to other milli-scale sensors, this could be a better option for sensing the length and angle data for milliscale actuators.