• Korean Journal of Optics and Photonics
• /
• v.15 no.3
• /
• pp.263-267
• /
• 2004

We have investigated the characteristics of a Nd:YAG laser pumped by a cw Ti:sapphire laser. When the pumping power of the Ti:sapphire laser was 850 ㎽, the maximum output power of the Nd:YAG laser was 450 ㎽. As a result, the slope efficiency for the output power of the Nd:YAG laser was measured to be 56%. We have also investigated the characteristics of a passively Q-switched Nd:YAG laser by using a Cr$^{4+}$:YAG as saturable absorber with initial transmission of 90%. The maximum average output power of 200 ㎽ was obtained with repetition rate of 23.8 KHz and pulse width of 17.0 ns.

• Korean Journal of Optics and Photonics
• /
• v.4 no.3
• /
• pp.301-308
• /
• 1993

Phenomenological nonlinear gain saturation effect on the modulation characteristics in a multi-electrode DBR laser, when the lasing wavelength changes, continuously is analized theoretically. FM efficiency, 3 dB bandwidth, and resonance frequency decrease with increasing bias current to the passive section, except increasing the flat FM response. It is found that the nonlinear gain saturation effect severely affects the modulation characteristics such as FM/IM response, 3 dB bandwidth, resonance frequency and CPR, but hardly affects the behavior of continuous frequency tuning.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.239-240
• /
• 2007

변압기 코어소재로 사용하는 방향성 규소강판의 가공 방법에 따른 물성을 조사하기 위하여 테이프 와인딩 코어 형태, 곡률반경을 20, 30, 40mm로 하여 토로이달 형태 변압기 시료의 B-H 자성 특성을 조사하였다. 곡률반경이 40mm, 높이는 10mm의 비율에서 보자력은 0.02Oe, 포화자속밀도는 0.98, 1.85T으로 보자력(Hc)은 낮고 포화자속일도(Bs)는 제일 큰 값을 나타내었고, 국내에서 생산되고 있는 방향성 규소강판의 자속밀도값 보다 약간 크게 나타났으며, 본 연구로부터 방향성 규소강판을 이용하여 권자심 코어을 제작할 때 고려해야하는 탄성변형에 대한 중요성과 코어 소재의 가공방법이 자기적 특성에 미치는 영향을 고찰하였다. 또한 토로이달 코어형태의 변압기를 설계 제작시 높이와 곡율반경, 가공 방법에 따라 용량, 효율 등이 다르므로 사전에 소재의 물성을 면밀히 검토 후에 전기기기에 적용해야함을 재확인하였다.

• Applied Chemistry for Engineering
• /
• v.32 no.2
• /
• pp.149-156
• /
• 2021

A kraft recovery boiler produces steam for power generation by the combustion of black liquor from the kraft pulping process. Since saturated steam became superheated in a superheater above the furnace, it is important to increase the heat exchange efficiency for the superheated steam production and power generation. A nose arch at the bottom of the superheater is important for blocking radiation from the furnace which causes corrosion of the superheater. But the nose arch is the main reason for creating a recirculation region and then decreasing the heat exchange efficiency by holding cold flue gas after the heat transfer to saturated steam. In this study, the size of recirculation region and the temperature of flue gas at the outlet were analyzed by the nose arch structure using computational fluid dynamics (CFD). As a result, when the nose arch angle changed from 106.5° (case 1) to 150° (case4), the recirculation region of flue gas decreased and the heat exchange efficiency between the flue gas and the steam increased by 10.3%.

• Journal of Soil and Groundwater Environment
• /
• v.14 no.6
• /
• pp.87-94
• /
• 2009

Surfactant-enhanced air sparging (SEAS) was developed to suppress the surface tension of groundwater prior to air sparging resulting in higher air saturation and larger contact area between NAPL and gas during air sparging. Larger contacting interface between NAPL and gas means faster mass transfer of contaminants from NAPL to gas phase. This new technique, however, is limited to relatively volatile contaminants because vaporization is its basic mechanism of mass transfer. In this study, SEAS was tested at an elevated temperature for a semi-volatile n-decane, which is expected not to be a good candidate of SEAS application due to its low vapor pressure at ambient temperature. Three sparging experiments were conducted using 1-dimensional column (5 cm id, 80 cm length) packed with sand; (1) ambient temperature ($23^{\circ}C$), column saturated with distilled water, (2) SEAS at ambient temperature ($23^{\circ}C$), for n-decane contaminated sand, (3) SEAS at elevated temperature ($73^{\circ}C$), for n-decane contaminated sand. Higher air saturation was achieved by SEAS compared to that by air sparging without surfactant application. The n-decane removal efficiency of SEAS at elevated temperature was significantly higher(> 10 times) than that of ambient SEAS. The n-decane concentrations in the gas effluent from column during SEAS at $73^{\circ}C$ are found to be 10 times of those measured at ambient temperature. Thus, SEAS technique can be applied for removal of semi-volatile contaminants provided that an appropriate technique for elevating aquifer temperature is available.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.3C
• /
• pp.234-240
• /
• 2002

A power amplifier with AlGaAs/InGaAs/GaAs HBT's has been developed for customer premise equipments of the quasi millimeter-wave frequency-band broadband wireless local loop(BWLL) system. Parameters of the linear and nonlinear equivalent circuits for a common base HBT have been extracted by a fitting method. The amplifier has been designed through the linear and nonlinear circuit simulations and fabricated on a ceramic substrate for a hybrid IC. The amplifier has produced a 25.5-dBm output power with 35% power-added efficiency(PAE) at 24.4 GHz and achieved a 7.5-dB linear power gain at 24.8 GHz. In 24.25 ∼24.75 GHz band, the amplifier has exhibited a saturated output over larger than 22 dBm and PAE higher than 25%.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2001.05a
• /
• pp.329-332
• /
• 2001

In this paper, it's shown that the saturable absorber Nd:LSB has a capability as a saturable absorber in Q-switching system. In the passively Q-switched 1.3${\mu}{\textrm}{m}$ Nd:YAG laser with saturable absorber, we theoretically investigated the optimized output mirror, peak power, output power, pulse width and output efficiency. The passively Q-switched Nd:YAG laser with saturable absorber Nd:LSB gives peak power of 30MW and pulse width of 6.23 ps at 30cm resonator length and output mirror reflectivity 98%. Consequently the output energies are 143, 200 and 209 $\mu$J at loss of 2.2%, 2.1% and 1.5%, respectively.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.5
• /
• pp.478-484
• /
• 2004

In this paper, two lossless snubber cells are proposed to generalize high frequency converter with losslless snubber. The selecting of snubber cells, which generalize high frequency converters, are depended on converter topologies. The cells have a saturable inductor, LC resonant tank and two diodes. In the cells, the saturable inductors extremely reduce resonant energy in the LC resonant tank. By minimizing resonant energy, the converter, which applies snubber cells, can operate at high frequency. These cells are applied for Buck, Boost, Buck-Boost, Cuk, ZETA, and SEPIC to generalize converter which have lossless snubber. The boost type converter has been implemented, with 400 kHz switching frequency for 125 W load to verify the converter characteristics.

• Korean Journal of Optics and Photonics
• /
• v.9 no.4
• /
• pp.231-235
• /
• 1998

Passively Q-switched, laser diode(LD) end-pumped Nd:YAG laser was demonstrated by using $Cr^{4+}$:YAG as a saturable absorber. In addition , we could calculate an excitation efficiency, which is an important parameter to evaluate the pumping geometry, directly by measuring the absorbed power in Nd:YAG at threshold condition. We found that output parameters such as average power, pulse duration, and repetition rate strongly depended on the low intensity transmission of $Cr^{4+}$:YAG and driving current of lase diode. The maximum Q-switched output power of 1 W was obtained with 40 kHz repetition rate. The pulse duration was varied from 50 ns to 200 ns.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.1
• /
• pp.231-238
• /
• 2019

In this paper, we have studied how to improve the amplifiers efficiency by minimizing the combining loss when several unit power amplifiers are combined to obtain high output power. Specifically, we have developed Ka-band Spatial Combining Amplifier. The fabricated Spatial Combining Amplifier is a Ka-band 20W class SSPA, which uses a 5W class unit amplifier module 8EA designed using a GaN bare die. We also combined The unit amplifier module using 8-way spatial divider and combiner with a hybrid radial structure. The output combining loss of the fabricated spatial coupler is about 0.334dB, which is about 92.6% efficiency. In this paper, we developed a Spatial Combining Amplifier with a maximum saturation output of 10W and a power addition efficiency of over 15%. As a result, we achieved the maximum saturation output of 30W and the power addition efficiency of 19%.