• The Journal of the Acoustical Society of Korea
• /
• v.34 no.3
• /
• pp.219-226
• /
• 2015

In this paper, derivation of the STL (Sound Transmission Loss) of a square plate installed in an impedance tube is discussed using an analytic method. Coupled motion of the plate vibration and acoustic field is considered. Vibration of the plate and pressure field inside the tube are expressed in terms of the infinite series of modal functions. Under the plane wave assumption, it is shown that consideration of the first few modes yields sufficiently accurate results. When the boundary of the plate is clamped, vibration mode is assumed as a multiplication of the beam modes corresponding to the crosswise directions. The natural frequencies of the clamped plate are calculated using the Rayleigh-Ritz method. It is found that the STL shows a dip at the lowest natural frequency of the plate, and increases as the frequency decreases below the natural frequency. Comparison of the result in this paper with the STL obtained by measurements and FE computations in the reference shows an excellent agreement.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.6
• /
• pp.496-503
• /
• 2009

In this paper, a new three-phase interleaved isolated high efficiency boost dc-dc converter with active clamp is proposed. The converter is capable of increased power transfer due to its three-phase power configuration, and it reduces the rms current per phase, thus reducing conduction losses. Further, interleaved operation of three-phase boost converter reduces overall ripple current, which is imposed into fuel cells and realizes smaller sized filter components, increasing effective operating frequency and leading to higher power density. Each output current of three-phase boost converter is combined by the three-phase transformer and flows in the continuous conduction mode by the proposed three-phase PWM strategy. An efficiency of above 96% is mainly achieved by reducing conduction losses and switching losses are reduced by the action of active clamp branches, as well. The proposed converter and three-phase PWM strategy are analyzed, simulated and implemented in hardware. Experimental results are obtained on a 500 W prototype unit, with all of the design verified and analyzed.

• Journal of the Korean Society for Railway
• /
• v.14 no.3
• /
• pp.222-227
• /
• 2011

The dropper supports the contact wire and is attached using various types of dropper clips on the catenary. Droppers are subject to mechanical stress from buckling during the passage of pantographs. In order to investigate failure causes for the high speed line dropper, theoretical analyses and experiments have been carried out. In this paper, mathematical formulas are derived for the pre-sag of the dropper static load. The measured values in the experiment were similar to the theoretical predictions. To analyze the cause on fracture of dropper wire, we have conducted analysis such as SEM(Scanning Electron Microscope) of fractured specimens in the field and new specimens. Finally, we performed measurement for the variation of dynamic load on the dropper when a pantograph moved at 300km/h under the Korean high speed overhead line. If such mechanical load occur repeatedly with every passing pantograph, it is possible that the dropper wire will break due to fatigue. This results will be used for special management of high speed catenary system maintenance and life estimation of dropper.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.8
• /
• pp.29-39
• /
• 1997

The clamp, as the structure which is used for supporting the pipe in the atomic power plant, is produced with a certain degree of anticlastic curvature in the current manufacturing process. In this study, the structural analysis of the clamp and the pipe was performed using ABAQUS. And the finite element modelling for the analysis was made by an HyperMesh. The contact forces which are transferred between the clamp and the pipe for the external force are changed according to the binding force of bolts and keeps the clamp tightly and protects the slipping between the clamp and the pipe. The clamps with the anticlastic curvature and with the flat curvature are considered in order to invest the anticlastic effect. In this study, another case is suggested. The present case does not have the stiffness ring on the end of the clamp but the suggested case has the ring. For the present case, the results showed that the equivalent stress is higher in the anticlastic curvature case than in the flat curvature case and the equivalent stresses on the pipe are almost the same as the binding force increses. For the suggested case, the result showed that the equivalent stress in the anticlastic curvature case decreases until some binding force and increases as the binding forces increase and is lower in some range than in the flat curvature case. From this study, the clamp with the anticlastic curvature in the suggested method is better than the clamp with the flat curvature and the optimal binding force are given.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.38 no.4
• /
• pp.307-316
• /
• 2002

In order to evaluate the deformation and stiffness of frame structure for fishery, composed of unit platforms which made of two concentric high density polyethylene buoys fixed by clamps and belts and rubber hinge components, under wave, the structural analysis for the square type of the structure was carried out by using finite element methods. The accurate physical properties of rubber hinge components determined by material tests were an important parameter to evaluate more reliable structural stability for the structure. The idealization to beam element with equivalent stiffness and rubber element with linearity for rubber hinges was necessary for the modeling of rubber component which has hyper-elastic characteristics. In addition, it was shown that the structural response of the structure under wave was larger in the hogging condition than that of in the still water or in the sagging condition.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.12
• /
• pp.31-36
• /
• 2011

This paper investigates the ESD robustness of the stacked output driver with a 0.13um CMOS process. To represent an actual I/O system, we implemented stacked output driver circuits with pre-drivers and a rail-based power clamp. We implemented eight kinds of circuits varying pre-driver input connections and stacked driver size. The test circuits are examined with TLP measurements. It is shown that breakdown current and voltage can be increased by connecting the pre-driver input to a power supply and using stacked devices of a similar size. Based on the test results, design guideline is suggested to improve ESD robustness of the stacked output drivers.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.18 no.1
• /
• pp.116-121
• /
• 2009

Thermosonic flip chip bonding is an important technology for the electronic packaging due to its simplicity, cost effectiveness and clean and dry process. Mechanical properties of the horn and the shank, such as the natural frequency and the amplitude, have a great effect on the bonding capability of the transverse flip chip bonding system. In this research, two kinds of study are performed. The first is the new design of the clamp and the second is the effect of tolerance parameters to the performance of the system. The clamp with a bent shape is newly designed to hold the nodal point of the flip chip. The second is the effect of the design parameters on the vibration amplitude and planarity at the end of the shank. The variation of the tolerance parameters changes the amplitude and the frequency of the vibration of the shank. They, in turn, have an effect on the quantity of the plastic deformation of the gold ball bump, which determined the quality of the flip chip bonding. The tolerance parameters that give the great effect on the amplitude of the shank are determined using Taguchi's method. Error of set-up angle, the length and diameter of horn and error of the length of the shank are determined to be the parameters that have peat effect on the amplitude of the system.

• Journal of IKEEE
• /
• v.20 no.3
• /
• pp.295-298
• /
• 2016

In this paper, we analysed the properties of the conventional ESD protection devices such as SCR, MVSCR, LVTSCR. The electrical characteristics and the turn-on time properties are simulated by Synopsys T-CAD simulator. As the results, the devices have the holding voltages between 2V and 3V, and the trigger voltage of about 20V with SCR, of about 12V with MVSCR, of about 9V with LVTSCR. The results of the simulation for the turn-on time properties are 2.8ns of SCR, 2.2ns of MVSCR, 2.0ns of LVTSCR. Thus, we prove that LVTSCR has the shortest turn-on time. However, the second breakdown currents(It2) of the devices are 7.7A of SCR, 5.5A of MVSCR, 4A of LVTSCR. This different properties have to be adapted by the operation voltages for I/O Clamps.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.4
• /
• pp.380-387
• /
• 2005

We report the performance of an open-frame type low-voltage high-current DC-DC converter module developed using an active clamp forward converter circuit and single ended rectifier. The converter module is designed with the specifications of an 3.3V output voltage, 30A output current, 100W output power and 36-75V input voltage. The synchronous rectifier is used to reduce the conduction loss at high current level and constant current control using precision PCB resistance is adapted to enhance the over current protection function in the system configuration. A prototype converter module is successfully implemented within 8mm height and quarter brick size (58x37mm) and recorded an $95W/in^3$ power density, 90.6$\%$ efficiency and 0.07$\%$ voltage regulation for the entire Input voltage range, thereby demonstrating its application potentials to future telecommunication electronics.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.6
• /
• pp.626-633
• /
• 2005

This paper proposes a new 2MVA SSFG(Sag Swell Flicker Generator) injecting voltage by using series inverter. The proposed SSFG composes series inverter, DC capacitor as energy storage, rectifier and voltage clamp circuit. This SSFG is designed to generate typical power disturbances, such as voltage sag/swell, over/under voltage and voltage flicker. Also it is designed to generate unexpected voltage phase jumping waveform by controlling the series inverter. In this paper, three kinds of control methods for the proposed 2MVA SSFG we investigated by PSIM simulation. Also typical voltage sag, swell, flicker waveforms are implemented by adopting effective control method.