• Journal of the korean Society of Automotive Engineers
• /
• v.15 no.4
• /
• pp.14-20
• /
• 1993

비조질강은 1970년대 초반 독일에서 개발된 이래 열처리(Quenching & Tempering)가 필요없는 에너지절약형 강재로서 유럽과 일본의 자동차업계를 중심으로 그 적용량이 지속적으로 증가되고 있다. 열간단조용 비조질강의 물성은 가열온도, 단조온도 및 냉각속도 등 단조공정변수의 영향을 크게 받는다. 본 고에서는 승용차엔진용 크랭크축에의 적용을 위해 SM50C에 V을 0.15% 첨가한 비조질강의 가열온도와 냉각속도에 따른 기계적 성질과 미세조직의 변화를 파악하여 최적단조공정을 정립하고, 크랭크 축시제품을 제작하여 그물성과 내구강도를 평가하고자 한다.

• Journal of the korean Society of Automotive Engineers
• /
• v.10 no.5
• /
• pp.9-16
• /
• 1988

엔진 크랭크축계의 비틀림진동은 엔진설계 및 제작에 있어서 오랜동안 주관심사였다. 크랭크축계의 비틀림진동에서 고려되는 문제는 비틀림진동계의 고유진동수와 이에 따른 차수별 엔진의 공진속도와 엔진의 공진속도에서의 비틀림진동각 및 크랭크축의 비틀림진동에 의한 토오크와 비틀림 응력 등이다. 당사에서는 simulation program을 개발했으며, 비틀림 진동측정 방법도 개발했다. 또한 비틀림진동 측정결과와 simulation결과의 비교로부터 simulation결과 및 측정결과의 정확도를 높여가고 있으며, simulation 방법의 개선을 모색하고 있다. 본 글에서는 이 program에 이용된 기본이론과 실험방법 및 댐퍼 선정 방법을 간단히 소개하고자 한다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.3
• /
• pp.40-49
• /
• 1994

This paper describes the method to investigate combustion pressure in the cylinder without modifications of engine. Assuming engine dynamics as a single degree of freedom cylinder pressure is estimated using the variation of crank shaft speed. For this study pressure, crank shaft sped, and load are sampled by the crank angle. This study suggests the variation of crank shaft speed can be used as parameters of feedback engine control.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.5 no.2
• /
• pp.29-37
• /
• 1996

High speed engines with high power are increasingly on demands and almost engines employ crankshafts Such problems as bending and torsional vibrations become the point at issue in crankshaft analysis and design. In this study to overcome the diffiiculty with the large amount of computation in finite element vibration analysis of a crankshaft, a reduction method based on influence coefficient and lumped parameter is presented. which reduces the computation amount effectively and can be used in vibrational analysis and design of any types of crankshafts Crank journal and pinparts are meodelled as elements with 6degrees of freedom per node. Crank web part is modelled using equivalent mass and stiffness matices . based up on lumped parameter and influence coefficient respectively to reduce total degrees of freedom considerablely. To confirm the scheme of the study the results are compared with the known data and they are coincident. Also a simple crankshaft is designed and manufactured for experiments. The calculated results using reduction method and the experimental results agree well The scheme of this study can be utilized in evaluation results agree well. The calculated result are compared with the known data and they are coincident. Also a simple crankshaft is designed and manufactured for experiments. The calculated results using reduction method and the experimental results agree well. The scheme of this study can be utilized in evaluation and development of high speed engine.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.4
• /
• pp.436-442
• /
• 2011

To obtain the engine output correctly is basically very important factor for estimating a engine performance. But, it has been reported that the IHP measured from electronic indicator such as MIPS(Mean Indication Pressure System) has a deviation compared to mechanical indicator. It was reported by authors that the uncertainty of crank angle for TDC position could be one of the reasons. In this paper, the uncertainty of crank angle for TDC position and its influence to engine output were investigated respectively about M/E and G/E for marine diesel engines. For the purpose, two sampling methods of pressure in cylinder were considered which were 'angle base sampling' and 'time base sampling'. Angle base sampling is real crank angle acquired from angle encoder which is attached to crank shaft and time base sampling is crank angle calculated by detected revolution with Z-pluse of encoder. Time base sampling is same method of MIPS. This paper concluded that time base sampling method is not suitable for obtaining the output of marine diesel engine on board because of instantaneous speed variation and load fluctuation. Also it is verified that the variation of engine speed by load fluctuation should be one of reasons additionally in case of M/E.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.11
• /
• pp.1529-1535
• /
• 2011

Improvement of the thermal efficiency in operation and maintenance of low- and medium-speed engines is a kind of never-ending requirement in the maritime power plant business. For the purpose of improving engine management efficiency, a principal factor that represents the fitness of the engine should be identified. Gas pressure, gas temperature, and vibration have all been used as this factor. However, they have limitations in terms of response speed and diagnosis accuracy. The EFR (engine fitness ratio) is suggested as a new diagnostic factor in this paper. The EFR is defined as the ratio of particular frequencies in the frequency domain and represents the fitness of an engine. It is calculated from the fluctuation pattern of the crankshaft angular speed. The EFR was verified using an experimental method for a low-speed engine and an analytic method for a medium-speed engine.

• Tribology and Lubricants
• /
• v.17 no.6
• /
• pp.426-434
• /
• 2001

The hermetic reciprocating compressor driven by the BLDC motor rotating with variable speeds, is modelled and analyzed for dynamic characteristics. The governing equations of piston, connecting rod and crank-shaft of the reciprocating compression mechanism and characteristics of driving torque of the motor are obtained. Dynamic behavior of the crankshaft supported on 2 journal bearings is analyzed considering compression load and eccentric unbalance for the 4 rotating speeds of crankshaft. And. reaction forces generated from oil film in the journal bearings are analyzed under transient condition using Reynolds' equation. To take into account the dynamic characteristics depending on the variable rotating speeds, comparison on the dynamic behavior of crank-shaft is made for the 4 operating modes of the compressor. Results show that the magnitude of crankshaft locioperating on the lower rotating speeds is more larger than the higher ones due to reduction of inertia force of the reciprocating piston.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.10 no.4
• /
• pp.287-294
• /
• 2016

Based on upper limb torque by different angles of a back, distance between crank axis and chest and angles of hand-grips, this research is to develop variable hand bikes. By doing so, it is to offer guidance for its design. For this research three normal persons took part in the experiment. Results are as follows. First, upper limb torque was found to be the highest at 50 degree of a back and muscle endurance was shown to be the highest at 80 degree of a back. It means that as a back of a chair gets lower the speed and efficiency becomes better, which contradicts the subjective fact that K-type hand bikes would show the highest speed. Second, among types of grips of hand bikes 45 degree ones have been shown to be the ones with the highest torque. This is due to proper distribution of power of joints in arms, elbows, and shoulders. Third, in case of distance of 45cm between crank axis and chest, it has shown the most efficient torque. This is because of the effect of gravity and exhaustion when handling.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.17 no.5
• /
• pp.15-21
• /
• 1980

An engine control system in which the conventional mechanical ignition system is studied. The contact point of the breaker is replaced by the contactless magnetic pick up sensor from which the information of the speed and the position of the crankshaft is extracted , and further an electronic High Energy Ignitim System Is designed, implemented and tested . The High Energy Igniticwl System increases the secondary spark voltage of the ignition coil from the conventional 10000~15000 volts to the 30000~40000 volts resulting in improving the combustion efficiency. Also, instead of the conventional advimce mechanism forigniliontiming control, a microprocessorbased timinng mechanisn is installed to determine the ignition timing data in response to the engine rpm and the intake manifold vacuum.

• Journal of Advanced Marine Engineering and Technology
• /
• v.41 no.1
• /
• pp.21-30
• /
• 2017

Of the marine engine components, the piston crown and exhaust valve are repaired most frequently. These works are conducted through conventional welding processes such as GTAW or SAW, domestically in marine engine repair factories. New high-efficiency welding or overlay processes such as tandem SAW, tandem MAG, hybrid TIG-MIG welding, pulsed-GMAW, CMT welding, and super TIG welding have been developed recently. Moreover, the plasma transfered arc (PTA) process is an efficient spray method for overlaying on the exhaust valve. In this review paper, the new high-efficiency repair welding methods are introduced for marine engine components. The problems due to repair welding for marine engine components are also presented.