• 한국자동차공학회논문집
• /
• 제12권6호
• /
• pp.30-37
• /
• 2004

The combustion and emission characteristics of a direct injection CI engine fuelled with DME(Dimethyl Ether) and diesel fuel were compared at idle engine speed(800 rpm) with various injection parameters. An optical single cylinder diesel engine equipped with a common-rail fuel injection system was constructed to investigate combustion processes of DME and diesel fuel. The combustion images were recorded with a high-speed video camera system. The results demonstrated that the DME-fuelled engine was superior to the conventional diesel engine in terms of engine performance and emissions. The optimal injection timing of DME was located around IDC(Top Dead Center), which was roughly same as that of diesel fuel. As the injection timing was advanced much earlier than TDC, NOx (Nitric Oxides) level increased considerably. NOx emission of DME was equal or a little higher than that for diesel fuel at the same injection pressure and timing because of higher evaporation characteristics of DME. Throughout all experimental conditions, DME did not produce any measurable smoke level.

• 한국자동차공학회논문집
• /
• 제17권5호
• /
• pp.107-114
• /
• 2009

A Common-Rail Direct Injection (CRDI) system for high speed diesel engines was developed to meet reductions of noise and vibration, emission regulations. High pressure in the common rail with electric control allows the fuel quantity and injection timing to be optimized and controlled throughout a wide range of engine velocity and load conditions. In this study, CRDI system analysis model which includes fuel and mechanical systems was developed using commercial software, AMESim in order to predict characteristics for various fuel injection components. The parameter sensitivity analysis such as throttle size, injection rate, plunger displacement, supply pressure of fuel injection for system design are carried out.

• 한국자동차공학회논문집
• /
• 제17권3호
• /
• pp.117-126
• /
• 2009

A Common-Rail Direct Injection(CRDI) system for high speed diesel engines was developed to meet reductions of noise and vibration, and emission regulations. In this study, CRDI system analysis model which includes fuel and mechanical sub-systems was developed using commercial software, AMESim in order to predict characteristics for various fuel injection components. Each component which constructs system was modeled and verified by sub-model of AMESim obtained characteristics curves of each components. The parameter sensitivity analysis such as throttle size, injection rate, plunger displacement, supply pressure of fuel injection for system design were carried out by the analysis.

• 한국분무공학회지
• /
• 제17권4호
• /
• pp.178-184
• /
• 2012

The aim of this study was to compare the spray characteristics of a typical fuel (100% diesel, DME) and diesel-DME blended fuel in a constant volume combustion chamber (CVCC). The typical fuel (100% diesel, DME) and diesel-DME blended fuel spray characteristics were investigated at various ambient pressures (pressurized nitrogen) and fuel injection pressures using a common rail fuel injection system when the fuel mixture ratio was varied. The fuel injection quantity and spray characteristics were measured including spray shape, penetration length, and spray angle. Common types of injectors were used.

• 한국자동차공학회논문집
• /
• 제12권6호
• /
• pp.96-102
• /
• 2004

The diesel particulate filter(DPF) is effective for particulate removal from diesel engine under a variety of conditions, and then the regeneration strategies is very important in the aspects of engine fuel consumption and engine durability. This paper addresses the changes of Peugeot 406 vehicle engine parameters(fuel injection timing, period, rail pressure, emissions exhaust temperature so on) during DPF regeneration. additionally, checked the soot loading mass with mileage and the change of fuel consumption and performance with ash accumulation.

• 한국정밀공학회지
• /
• 제26권2호
• /
• pp.54-62
• /
• 2009

The purpose of this study is to develop a piezo injector driver for common-rail direct injection diesel engines. In this research, we analyzed the electrical and mechanical characteristics of the piezo actuator through experiments. Current flow and charging voltage of the piezo injector are controlled by the PWM signal of variable duty ratio in order to realize both fast response and low peak current. The optimal switching duty ratio was designed by modeling and analyzing of the piezo driver circuit. In order to avoid resonance and unacceptably long settling time, appropriate frequency range of the PWM signal was derived based on the driver circuit model. The developed injector driver was validated by experiments under various fuel rail pressure, injection duration, and charging voltage.

• Journal of Advanced Marine Engineering and Technology
• /
• 제34권4호
• /
• pp.508-514
• /
• 2010

본 논문은 커먼레일 디젤엔진의 정속운전시 배출되는 나노크기의 입자상 물질을 분석하는데 초점을 두었다. 디젤산화촉매 후단에서 나노입자상 물질의 개수농도 저감수준은 크지 않았으나 매연여과장치 후단에서 분석한 결과 1,000배 정도 저감되는 결과를 확인하였다. 고속 고부하 조건에서는 매연여과장치의 자연재생 효과로 인해 입자상 물질은 증가하였다. 연료분사시기를 BTDC $6^{\circ}CA$ 에서 ATDC $4^{\circ}CA$까지 지각시킨 결과 입자상 물질의 개수농도는 감소하였지만 최지각 조건인 ATDC $9^{\circ}CA$에서는 증가하는 결과를 확인하였다. EGR 적용시 핵화모드 입자상 물질은 저감되는 경향을 보였으며 축적모든 입자는 증가하였다.

• 한국자동차공학회논문집
• /
• 제21권4호
• /
• pp.89-95
• /
• 2013

In this work, the evaluation of swirl nozzle injector performance was conducted by investigating effective area ($A_{eff}$), injection mass ($m_{inj}$), injection rate ($Q_{inj}$), and injection delay ($t_{delay}$) under various test conditions. To achieve these, fuel injection analysis system which was composed of fuel supply system, injection system, and control system was installed. At the same time, the swirl nozzle that had 12 orifice hole with $120^{\circ}$ injection angle was used in this work. It was revealed that the difference of injection mass ($m_{inj}$) between base and swirl nozzle injector increased as the injection pressure ($P_{inj}$) and energizing duration ($t_{eng}$) decreased under the same test conditions. The maximum injection rate ($Q_{inj}$) of swirl nozzle injector was higher than base nozzle injector about 2~5%. The injection performance of swirl nozzle was better than base nozzle at low injection pressure ($P_{inj}$) and short energizing duration ($t_{eng}$) conditions.

• Journal of Advanced Marine Engineering and Technology
• /
• 제39권9호
• /
• pp.911-917
• /
• 2015

본 논문에서는 함정용 디젤연료를 단기통 커먼레일 디젤엔진에 적용하여 연료분사압력 변화에 따른 분사율 특성, 거시적 분무 특성 및 연료분사시기와 연료압력변화에 따른 연소 및 배기가스 배출특성을 분석하는데 초점을 두었다. 분사율 특성은 Bosch법을 적용한 분사율 측정 시험 장치를 이용하여 분석하였고, 거시적 분무 특성은 정적용기 및 초고속 카메라를 이용하여 분석하였다. 또한, 연료분사시기 및 연료압력 변화를 정밀하게 제어할 수 있는 단기통 엔진을 이용하여 연소 및 배기가스 배출특성을 분석하였다. 30MPa과 50MPa의 분사조건에서 초기 분사율은 50MPa의 분사조건에서 크게 나타났으며, 분무 발달(투과) 또한 동일시간대에서 큰 것으로 분석되었다. 연료분사시기가 지각될수록 실린더 내부 최대 압력과 최대 열발생량은 떨어지는 경향으로 나타났으며, 고압분사조건에서 실린더 내부 최대압력과 최대 열발생량은 다소 큰 것으로 분석되었다. 고압분사조건에서 도시평균유효압력은 낮은 것으로 분석되었고, 연료분사시기가 TDC 쪽으로 지각될수록 도시평균유효압력 및 토크는 증가하는 것으로 나타났다. 연료분사시기가 $BTDC20^{\circ}$(30MPa)와 $BTDC15^{\circ}$(50MPa)에서 질소산화물 발생수준이 가장 높았으며, 일산화탄소는 $BTDC30^{\circ}$를 기준으로 지각될수록 저감되었다.

• LP가스
• /
• 제20권2호
• /
• pp.59-67
• /
• 2008

지난 4월 2일 GAS KOREA 2008 전시회가 개최된 서울무역전시장에서 '한국DME협회 분과발표회'가 열렸다. 이날 분과발표회에서는 'DME Demo 플랜트 현황소개(한국가스공사 연구 개발원 조원준 박사 "DME 연료실증, 시험연구 사업현황(한국가스공사 연구개발원 백영순 박사)" 커먼레일형 연료공급계를 탑재한 2리터급 DME 차량개발(자동차 부품연구원 정재우 박사) "급속압축장치를 이용한 불균일 예혼합기의 DME HCCI연소 과정에 관한 연구(울산대학교 임옥택 교수) DME의 자착화 측정 및 세탄가의 추정(인하대학교 이대엽교수)" 직접분사식 압축착화기관에서 DME연료의 분무미립화 및 배출물 특성(한양대학교 이창식 교수)' 에 대한 발표도 이뤄졌다.